Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Discussion Topics > Exhaust System

Reply
 
Thread Tools Display Modes
  #1   IP: 98.10.17.101
Old 07-18-2022, 08:30 PM
Paul_P30 Paul_P30 is offline
Member
 
Join Date: Jul 2022
Posts: 1
Thanks: 0
Thanked 0 Times in 0 Posts
rebuilding exhaust question

I am rebuilding the hot section of the exhaust from the A4 to the muffler of my P30. The water inlet fitting I bought last week from Moyer has a 1 5/8 inch OD. The fitting on the muffler is 1 1/2 inch OD. It looks like the previous owner stretched a 1 1/2 hose over the (now failed) Onan water inlet. What is a good way to stretch a new hose over the fitting? is there a marine exhaust hose safe 'grease'? Or would hose clamps seal a 1 5/8 inch hose to a 1 1/2 muffler? That doesn't sound like a good idea?
Thanks,
Paul
Reply With Quote
  #2   IP: 209.121.229.215
Old 07-19-2022, 02:12 AM
Marty Levenson Marty Levenson is offline
Senior Member
 
Join Date: Nov 2004
Location: Bowen Island, BC
Posts: 677
Thanks: 86
Thanked 36 Times in 32 Posts
heat

Not sure about your exact situation, but in general heating the hose before pushing it onto a fitting works wonders. Holding the hose in hot water for a minute or two is best: a heat gun is my second choice if that's too awkward.
__________________
Marty
1967 Tartan 27
Bowen Island, BC

Reply With Quote
  #3   IP: 75.118.33.103
Old 07-19-2022, 05:26 AM
msmith10's Avatar
msmith10 msmith10 is offline
Senior Member
 
Join Date: Jun 2006
Location: Columbus, Ohio
Posts: 438
Thanks: 12
Thanked 31 Times in 23 Posts
And to lube the hose use some Dawn. Greases can eat hoses.
__________________
Mark Smith
1977 c&c30 Mk1 hailing from Port Clinton, Ohio
Reply With Quote
  #4   IP: 162.245.50.196
Old 07-19-2022, 08:36 AM
Dave Neptune Dave Neptune is online now
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Grove, Oklahoma
Posts: 4,682
Thanks: 604
Thanked 927 Times in 622 Posts
Exclamation

Paul, not sure if you are trying to reduce an 1 5/8 on to an 1 1/2 or stretch an 1 1/2 on to an 1 5/8 however your right that it's not a good idea. You want the integrity of anything that can leak dangerous gasses or water into the boat to be done correctly so it is safe for you and the crew. IMHO.

You could maybe cobble an adaptor together or find one.

Dave Neptune
Reply With Quote
The Following 3 Users Say Thank You to Dave Neptune For This Useful Post:
Peter (07-19-2022), TimBSmith (07-19-2022), W2ET (07-19-2022)
Reply

Tags
exhaust hose, water inlet

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Exhaust Riser Question bigd14 Exhaust System 8 07-07-2021 01:44 PM
Rebuilding exhaust system for Catalina 30(hot section) ajgaines Exhaust System 18 09-13-2019 05:03 PM
Tartan-30 Exhaust Question TomG Exhaust System 15 11-24-2010 03:29 PM
Exhaust Manifold Question LastLeg Exhaust System 6 10-10-2009 05:23 AM
Believe I have stuck exhaust valves. Still have a question P30_889 Troubleshooting 101 06-11-2009 04:08 PM


All times are GMT -4. The time now is 01:39 PM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2022, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2022 Moyer Marine Inc.

All Rights Reserved