Hello all
I hope to gather some wisdom from the all the salty experience around here. I am having that common problem where the A4 in our 1982 Catalina 30 runs, idles, and revs smoothly like a top when neutral, but stalls within seconds when put into gear. I have read dozens and dozens of discussion threads so I have a lengthy list of troubleshooting items. However, due to my inexperience, I am running into some issues in the first step -- checking to see if my prop shaft will turn by hand in neutral.
1) With 2 of us boat partners gripping the prop shaft, while in neutral, we were unable to budget the prop shaft at all, not even a fraction of a mil, using our bare hands. However -- we do not have a standard stuffing tube, instead we have one of those PSS Shaft Seal systems, where the stainless steel collar is pressed against a graphite puck under pressure from the rubber bellows. Should the shaft still be turning freely by hand even with the PSS shaft seal system?
2) Would it be a worthwhile test, if I de-coupled the prop shaft from the coupling flange at the engine shaft output, and then tried again to turn the shaft by hand? (And if I understand correctly, I should carefully use my feeler gauges when slowly re-tighten the bolts connecting my prop shaft to the coupling flange - correct?)
We're already planning to hire a diver to check for lines or other debris fouling the prop or shaft outside the boat, but I want to check for excess shaft binding this weekend. Was just hoping that #1 above -- was already good enough indicator that my shaft binding is the issue.
BACKGROUND: New (to us) boat had an extremely well maintained A4, and motored everywhere with no problems. At end of March, we motored 2 hours to get to a shipyard where, for the next 4 weeks, we got all standing rigging replaced. Boat was never lifted out of the water. After 4 weeks, we start the engine, put into gear, and stalled after a few minutes.
After more attempts, the engine now stalls almost immediately (prop shaft turns 4-5 times) and then it stops). With all of this, I believe the issue is shaft binding, so was hoping to confirm.
Would appreciate if someone could confirm if in neutral, with PSS seal, prop shaft could be easily turned.
thanks
I hope to gather some wisdom from the all the salty experience around here. I am having that common problem where the A4 in our 1982 Catalina 30 runs, idles, and revs smoothly like a top when neutral, but stalls within seconds when put into gear. I have read dozens and dozens of discussion threads so I have a lengthy list of troubleshooting items. However, due to my inexperience, I am running into some issues in the first step -- checking to see if my prop shaft will turn by hand in neutral.
1) With 2 of us boat partners gripping the prop shaft, while in neutral, we were unable to budget the prop shaft at all, not even a fraction of a mil, using our bare hands. However -- we do not have a standard stuffing tube, instead we have one of those PSS Shaft Seal systems, where the stainless steel collar is pressed against a graphite puck under pressure from the rubber bellows. Should the shaft still be turning freely by hand even with the PSS shaft seal system?
2) Would it be a worthwhile test, if I de-coupled the prop shaft from the coupling flange at the engine shaft output, and then tried again to turn the shaft by hand? (And if I understand correctly, I should carefully use my feeler gauges when slowly re-tighten the bolts connecting my prop shaft to the coupling flange - correct?)
We're already planning to hire a diver to check for lines or other debris fouling the prop or shaft outside the boat, but I want to check for excess shaft binding this weekend. Was just hoping that #1 above -- was already good enough indicator that my shaft binding is the issue.
BACKGROUND: New (to us) boat had an extremely well maintained A4, and motored everywhere with no problems. At end of March, we motored 2 hours to get to a shipyard where, for the next 4 weeks, we got all standing rigging replaced. Boat was never lifted out of the water. After 4 weeks, we start the engine, put into gear, and stalled after a few minutes.
After more attempts, the engine now stalls almost immediately (prop shaft turns 4-5 times) and then it stops). With all of this, I believe the issue is shaft binding, so was hoping to confirm.
Would appreciate if someone could confirm if in neutral, with PSS seal, prop shaft could be easily turned.
thanks
Comment