Originally posted by jcwright
View Post
Trouble starting engine - valve open?
Collapse
X
-
Originally posted by JOHN COOKSON View PostThat valve will have to be open so fuel can get to the engine.
The raw water cooling valve should be closed when cranking a no start engine.
A fully charged battery does not guarantee that you have spark. Have you confirmed that you have spark? Have you tried shooting starting fluid into the carburetor while cranking the engine? We will be able to help further if you could supply details. The first step is to figure out if the no start is due to a problem with fuel, spark or compression since all three are needed for the engine to start.
ex TRUE GRIT
Hi John, where might I find my raw water cooling valve?
Comment
-
-
Originally posted by wetbirks View Post...where might I find my raw water cooling valve?
(See PIC #1)
Follow the hose attached to it to where it connects to a THRU HULL.
(See PIC #2)
Your valve may look a little different but basically you're looking for something with a valve attached to the hull.
(More reading on this HERE)
That valve feeds your cooling system and is commonly referred to as the Raw Water Cooling Valve.
On that note, Forum Crew...
We should maybe re-think how we refer to closing that "valve" for clarity to newbies? Just a thought.-Jerry
'Lone Ranger'
sigpic
1978 RANGER 30
Comment
-
-
The inner wire for the choke is not connected to the dohicky on the choke; it appears to be resting on the part itself. The engine will not start unless it is choked, especially when cold.
To review: To start the engine needs fuel, spark, compression
in the cylinders. Also the choke must be working and the spark needs to be at the right time (timing).
The raw cooling water intake valve in located on the hull of the boat at the other end of the water pump inlet hose. When you crank the engine the water pump is turning and pumping water. Exhaust pressure will blow this water out when the engine is running. When the engine isn't running water can accumulate in the exhaust system and flood back into the engine if the engine is no start cranked for to long of a period of time.
A BELATED WELCOME TO THE FORUM. We'll get your engine running. Hang in there.
ex TRUE GRIT
Edit: Jerry beat me to it with some excellent picturesLast edited by JOHN COOKSON; 07-03-2021, 10:31 AM.
Comment
-
-
[QUOTE=JOHN COOKSON;126028]The inner wire for the choke is not connected to the dohicky on the choke; it appears to be resting on the part itself. The engine will not start unless it is choked, especially when cold.
Is this what you're referring to? I'm heading down to the boat in about an hour and I will give it a closer inspection to make sure it is attached.
Thank you for the warm welcome! I so much appreciate the help I received.
Comment
-
-
Originally posted by wetbirks View PostThank you for helping me locate that valve. I will turn it off when I try to start the engine again. At what point would I reopen it?
That circled area (choke arm) is indeed what John was referring to.
In the below pics you can see how is is supposed to be attached.-Jerry
'Lone Ranger'
sigpic
1978 RANGER 30
Comment
-
-
Originally posted by roadnsky View PostLook at the REAR (StarBoard) side of your engine and locate the WATER PUMP.
(See PIC #1)
Follow the hose attached to it to where it connects to a THRU HULL.
(See PIC #2)
Your valve may look a little different but basically you're looking for something with a valve attached to the hull.
(More reading on this HERE)
That valve feeds your cooling system and is commonly referred to as the Raw
On that note, Forum Crew...
We should maybe re-think how we refer to closing that "valve" for clarity to newbies? Just a thought.
Located the wrong water cooling valve. It was in the off position already.
Comment
-
-
Originally posted by JOHN COOKSON View PostThe fuel pump itself may need to be primed depending on your boat's fuel system is set up. The A4 fuel pump can have problems with dead lift.
ex TRUE GRIT
After eliminating a few other issues, I've moved on to priming the fuel pump. It just emits a dry squeaky sound after pumping it for many minutes. I'm convinced that the fuel is not being drawn through the system. When I disconnect the hose clamps throughout the system I just find dry fuel line starting at the tank all the way down to the fuel pump.
Any suggestions on why the fuel is not leaving the tank?
Comment
-
-
After doing a few things mentioned in this form, I'm convinced that my next step is to figure out an issue with fuel delivery. The manual fuel pump makes a continuous squeaky noise that doesn't seem to be drawing fuel into the engine. When I remove the clamps and pull the fuel lines in various locations between the tank and the fuel pump, the lines are all dry. So I am certain that there is no fuel passing through the fuel lines.
I added 20 L of fuel last week.
Any suggestions on my next steps to troubleshoot this?
Please recall that I did run the fuel tank empty prior to adding the new fuel.
Comment
-
-
Originally posted by wetbirks View PostAny suggestions on why the fuel is not leaving the tank?
There is a blockage between the tank and the fuel pump such as a blocked filter.
The end of the outlet tube in the tank may be blocked.* Especially if there is some sort of a filter on the end of the outlet tube in the tank.
ex TRUE GRIT
*Edit: Did you try blowing into the tank and listening for bubbles?Last edited by JOHN COOKSON; 07-03-2021, 08:35 PM.
Comment
-
Comment