Reversing gear video
Collapse
This is a sticky topic.
X
X
-
How does Bar connects to the Brake Band (Reversing Gear)
Any still pictures/drawings/web site/etc available that show how the Brake Band Reversing Bar, MMI #161 (OXX Paragon Reversing Gear) connects to the Reversing Gear Brake Band, MMI #253? Same concerning how the Spring connects. I'm in the process of putting it all back together, and I can't remember how it fits. I knew I should have taken better notes.
Emmett
-
-
Emmett,
If you have a copy of our MMI Service and Overhaul Manual, Chapter 6 has pictures showing how the reversing bar is configured. I don't know of any other place where good still pictures exist of this assembly. Basically, the end of the bar with the connecting hook installs into the top of the shifting yoke, and the end of the bar with a ramp slides between the roller in the end of the adjusting bolt and the large ear of the brake band.
Don
Comment
-
-
Which way is clockwise?
This is a silly question and it's probably answered in many places but..
In the 'Forward Mode Adjusting Procedure' in Chapter 6 of the Overhaul Manual, in step 6 it says turning the adjusting collar clockwise will tighten the clutch. Clockwise as you face which direction? I will be looking at the 'transmission' in the same direction as the picture in Fig 7. Will I rotate the adjusting collar to the right or left as seen in that picture to tighten Forward Mode.
And is this the right adjustment if my engine "slips out of gear" when I give it too much throttle? If I just back off the throttle it re-engages and I can accelerate again but it slips out at about 1500-1600 rpm.
Thanks,
Randy
Comment
-
-
Clockwise as if you were behind the engine looking forward at the reversing gear. In the video clip, you would be standing at Don's right looking at the shaft end of the reversing gear. Adjusting the collar by turning it clockwise should reduce and ultimately eliminate all slipping. It's a trial and error process. Let us know how you make out.
Mark S
Comment
-
-
Thanks Mark. I'll check back after I dig into it. I think I must have been cutting it close before but I had to put a new shifter cable on and it probably is ever so slightly different than the old one. I'll go through Don's full procedure including adjusting the reversing gear.
Comment
-
-
I adjusted my Forward and Reverse today as reverse was not engaging. It was a lot easier than I feared it might be but Don's video, like all of them, was excellent and demystifying.
My shifter is (has always been) pretty hard to engage into "forward" so I changed it by one cog and it felt much better. Great I thought. I adjusted the "reverse" one turn of that nut to the next flat and now reverse is great.
My issue is that my engine never got over 1200RPM underway, clean bottom and prop etc. It's just he way it's been since I bought it 14 years ago. With the new "forward" adjustment, I'd get up to about 1000RPM and it would slip out and the RPM would runaway. So I took back that one cog I gave it and decided that I'd just have to live with the very firm engagement on the lever.
Here's my issue, with forward engaged (now back to the original gear cog) and prop pushing, I'm now getting 1800RPM underway. Since I've never been able to get more than 1200RPM it made me wonder if something could be slipping and subsequently overheating? If it's in forward and the prop is driving, is it "in" or "out" with nothing inbetween? Can something slip when engaged if not properly adjusted? I just can't figure out why I'd now have 600 extra RPM since I set it back to the original setting.Rob--
"Who is staring at the sea is already sailing a little."
1968 C&C Invader 36' / Late Model Atomic4
https://www.tumblr.com/sherloch7
sigpic
Comment
-
-
Rob, that is perplexing to say the least. As the reversing gear uses "wet clutches" any slippage when under power will cause over revving of the engine and not a controlled steady RPM issuing power to the prop. Just a note it does take far more force than anticipated to engage the lock in forward on these transmissions.
Was anything cleaned like the prop? Was the engine adjusted in any other way like a tune up at the same time?
Dave Neptune
Comment
-
-
My engaging the transmission has always been really firm, like you say, harder than anticipated. But, it's the only Atomic 4 i've ever driven so I have nothing to compare to. Mine might be absolutely normal. But, I'm used to it, it's been the same for 14 years since I bought it.
I did to a tuneup, but checked the RPM afterwards to see if I gained anything. I might have gained 500RPM or so but it really was close to where it's always been on my RPM meter. So, nothing odd there.
But, after that tuneup, literally two days later, I checked the RPM again before doing the transmission adjustment and it was the same. Then, after the transmission tune up and then, "tune back down", I see the RPM change. That's what had me wondering if it could still be engaged and pushing, but also slipping. I have a friend with a Westerbeke who has has a lot of transmission slippage and overheating.
I know our transmissions are different and from reading all of you guys forum posts, I assumend that either it's "in" in forward or "out" and can't be inbetween and slipping. I think that's what I'm hearing, that in 'forward', it can't slip. I ran it for an hour yesterday under full power and everything was fine, just much higher in RPM than ever before.Rob--
"Who is staring at the sea is already sailing a little."
1968 C&C Invader 36' / Late Model Atomic4
https://www.tumblr.com/sherloch7
sigpic
Comment
-
-
I have a similar boat 1966 Morgan 34 with original A4, owned for 46 yrs. A few years back I had some variable slippage problems sometimes after a long run. One of the causes i believe was that I used some 10w-30 synthetic blend oil during a mid season oil change - perhaps too much lubricity in a warm engine for the reversing gear plates, went back to regular oil. 2nd cause was some surface rust on the cable near the pin end prior to the shift handle. 3rd this helped the cable sheath to slip occasionally in the hold down clamp - had the pre drilled holes for it so I added a second "U" clamp and tightened the first. I too also thought it was the adjustment ring and the one notch adjustment did increase effort required to engage the shift lever. Steps 1,2 & 3 solved issue.
Comment
-
-
Dave, yes, I do. You can feel it drop in and set. If I gave it a name it would be "soft clunk."
Sam, interesting. I use 30W consistently. I think you are mainly talking about "reversing" right? I know it can slip as it's pressure plates. Have you had slipping in forward? Again, I don't think this can happen if I'm understanding the system more. Once those gears lock in, it's like it's one piece of metal from the drive shaft to the propshaft. Don talks about it some.Rob--
"Who is staring at the sea is already sailing a little."
1968 C&C Invader 36' / Late Model Atomic4
https://www.tumblr.com/sherloch7
sigpic
Comment
-
-
I had intermitent slippage in forward and reverse but usually after a long run ie motoring to the yard for haul out etc - needed high rpm just to move slowly. I switched back to regular oil and made sure cable could not slip in clamp. I tested did not need the extra ring adjustment and set it back to the initial setting - still has a nice detent "feel" and not too much shift lever force needed. Sometimes we make things too complicated.
Comment
-
Comment