Forum: Overhaul
Today, 06:02 PM
|
|
Replies: 3
Views: 42
|
|
Forum: Tools wanted or offered to rent
Today, 03:42 PM
|
|
Replies: 6
Views: 42
FWIW, I also damaged my tool when trying to...
FWIW, I also damaged my tool when trying to compress the springs. I see in my notes this comment from Don on a possible cause of this problem:
"Over the years, varnish in the oil will...
|
|
Forum: Tools wanted or offered to rent
Today, 02:27 PM
|
|
Replies: 6
Views: 42
Hello denisla.
The spring compression tool...
Hello denisla.
The spring compression tool is available in the MMI catalog. Here is the link to the tool:
https://moyermarine.com/product/valve-spring-compressing-tool-tool_02_165/
...
|
|
Forum: Overhaul
Today, 01:25 PM
|
|
Replies: 3
Views: 42
Hello dplidr.
Here is a comment from Don...
Hello dplidr.
Here is a comment from Don Moyer from a related earlier thread:
"There is a small "0" on the front face of one of the teeth of the small crankshaft gear and a small "0" between...
|
|
Forum: Ignition System
01-18-2021, 04:16 PM
|
|
Replies: 6
Views: 168
|
|
Forum: Overhaul
01-16-2021, 11:06 AM
|
|
Replies: 5
Views: 217
Hello Splashdog.
I'm not sure it will help...
Hello Splashdog.
I'm not sure it will help with your situation, but below is a link to drawings that show the locations of the mounting holes for a late model A4. I've highlighted the hole...
|
|
Forum: Troubleshooting
12-26-2020, 07:46 PM
|
|
Replies: 16
Views: 338
Hello Al and Dave.
I believe your original...
Hello Al and Dave.
I believe your original post noted that starter fluid had no effect. I'm curious what you and others think about the view that this suggests problems with ignition. Did you do...
|
|
Forum: Overhaul
11-20-2020, 02:23 PM
|
|
Replies: 4
Views: 459
|
|
Forum: Troubleshooting
11-14-2020, 06:23 PM
|
|
Replies: 11
Views: 525
Tom,
My first concern would be to deal...
Tom,
My first concern would be to deal with the water in the cylinders before that causes more serious problems. Below is a note from Don Moyer that may be helpful.
Best regards,
Jack. ...
|
|
Forum: Overhaul
11-12-2020, 03:15 PM
|
|
Replies: 34
Views: 1,799
|
|
Forum: Safety
11-06-2020, 03:39 PM
|
|
Replies: 11
Views: 692
|
|
Forum: Safety
11-06-2020, 01:09 PM
|
|
Replies: 11
Views: 692
|
|
Forum: Safety
11-06-2020, 09:48 AM
|
|
Replies: 11
Views: 692
Art: If you or others think of measurements I...
Art: If you or others think of measurements I could take of my head, let me know. Also, I’ve tried before to give my head to someone who could use it, without luck so far. The engine was running...
|
|
Forum: Safety
11-05-2020, 07:17 PM
|
|
Replies: 11
Views: 692
|
|
Forum: Safety
11-05-2020, 06:50 PM
|
|
Replies: 11
Views: 692
|
|
Forum: Safety
11-05-2020, 04:36 PM
|
|
Replies: 11
Views: 692
Your pinhole leak sounds similar to one I had....
Your pinhole leak sounds similar to one I had. IIRC, the leak occurred where wire was attached to the head during casting. I drilled and tapped the hole and filled it with a stainless socket plug. I...
|
|
Forum: Troubleshooting
11-01-2020, 09:48 AM
|
|
Replies: 14
Views: 684
Hello Tbird.
You mention that the fuel pump...
Hello Tbird.
You mention that the fuel pump was tested, but not how. Perhaps you've already checked for fuel pressure downstream of the fuel pump. If not, a fuel pressure gauge is worth...
|
|
Forum: General Maintenance
10-28-2020, 11:42 AM
|
|
Replies: 27
Views: 1,525
|
|
Forum: General Maintenance
10-28-2020, 11:16 AM
|
|
Replies: 27
Views: 1,525
Tim,
I forgot to answer your question about...
Tim,
I forgot to answer your question about the numbers stamped on the piston:
One of the numbers is "2.56055". My average cylinder bore measurement was 2.563. The standard cylinder bore in...
|
|
Forum: General Maintenance
10-28-2020, 10:43 AM
|
|
Replies: 27
Views: 1,525
Tim,
Here are my notes on my overhaul:
...
Tim,
Here are my notes on my overhaul:
https://drive.google.com/file/d/0B869NyQaShwZSFFvRGtUQ0JUWTQ/view?usp=sharing
My notes merely describe what I did, not how it should be done. Some...
|
|
Forum: General Maintenance
10-28-2020, 08:45 AM
|
|
Replies: 27
Views: 1,525
|
|
Forum: Troubleshooting
10-27-2020, 09:20 PM
|
|
Replies: 3
Views: 285
|
|
Forum: Overhaul
10-21-2020, 01:39 PM
|
|
Replies: 46
Views: 2,369
|
|
Forum: Overhaul
10-21-2020, 10:39 AM
|
|
Replies: 46
Views: 2,369
Hello again Greg.
Yes, I was referring to...
Hello again Greg.
Yes, I was referring to the smaller hole, not the one for the stud.
I also checked the parts manual last night. I wasn't able to find the set screws either on the page that...
|
|
Forum: Overhaul
10-21-2020, 09:19 AM
|
|
Replies: 46
Views: 2,369
|
