Shake, Shake, Shake was the thread that started at the very beginning, but now I am in the engine... I've removed the manifold, valve cover, etc. and must decide if there is anything I should actually do in there! My question today is about the two valves that have shiny rings... the photo shows the 3rd (on the left) through 8th (aftmost) exhaust valve on the right. So 8 seems to be stuck up? Number 3 is touching against the tappet (tight, holds it from revolving), is that anything? See anything of interest? Lots of MMO that I put down the plug holes.
Valves revealed.... photos.
Collapse
X
-
Furthest one back, on the right in the pic, is stuck. The spring is still compressed and it's not seated on the lifter. I can't really see the others really close. What you need to do is just remove the coil wire, shut off your raw water, and turn the engine over. Remember, if you have electronic ignition don't leave the key in the on position...always turn if all the way off once you have turned it over. Don't want to burn out your EI.
You want to see all valves and springs move. The lifters, come up, move the valve, all springs compress, as the stroke changes, the springs pull the valves back down onto the lifter. Keep in mind there's a slight gap, I'd have to look that up, but it's done with a feeler gauge. Those valves should be set if the engine was a runner. I'll let Dave Neptune, Al, Ed and a few more chime in on releasing that valve. I've never had any luck doing it from the side plate and always had to remove the head...they were either broken, seized good or both.Last edited by Mo; 03-31-2021, 08:57 PM.Mo
"Odyssey"
1976 C&C 30 MKI
The pessimist complains about the wind.
The optimist expects it to change.
The realist adjusts the sails.
...Sir William Arthur Ward.
-
-
All I see is that one valve stuck. You are there now with the side of the engine. Did you ever try the acetone mixture prior to this? Quite frankly speaking, if that didn't free it you just may have to pop the head off.Mo
"Odyssey"
1976 C&C 30 MKI
The pessimist complains about the wind.
The optimist expects it to change.
The realist adjusts the sails.
...Sir William Arthur Ward.
Comment
-
-
Did you try the allen wrench trick through the spark plug hole now that you know the which valve is the culprit?
Mo and Peter thought are spot on you need an more aggressive penetrating lubricate than WD-40. I've used Seafoam as well, but you will need to way to spray it on the valve so it will run down the stem into value bushing. I've had good luck with PB-blaster and it comes with a nice spray tube (like WD-40).Thanks,
Ron
Portland, OR
Comment
-
-
great pics!
I agree with the previous comment:
- make sure water valve and ignition is off, and slowly turn the engine by hand, watching all the valves: you want to make sure that all valves go up and down; here there is clearly one stuck (as expected).
- spray your favorite lubricant / sprayfoam etc... on the springs, but also through the manifold holes (as you have great access to the lower valve guides).
- on the blocked valve, gently scrap + brush the crude on the spring.
- Moreover, and this is my personal advice only: once you have sprayed a good amount of the right product, set the tapet of the blocked valve on the low position (by rotating the engine manually, in order to have as much room as possible), and with a pair of small vice grip, grab the very bottom of the valve stem (below the spring), and try to gently rotate+shake it (making sure not to bend it). With some luck, that should allow the valve to get loose.
After all valves are freed and moving, best is probably to check the gap. Let's see what the other think, but in my mind, cranking the engine with the starter a few extended times (with water valve closed, fuel pump disconnected, ignition off) may be a good thing to make sure the previously blocked valve moves up and down a few dozens times to hit its seat and break any remaining gunk before you check the gaps. Other Afourians, opinions?
Good luck!
PS: and best pratice any time you work around those valves: put a couple small pieces of rags on the oil drain holes at the bottom of this cavity, just in case something gets loose. And make sure to remove them before closing the hatchLast edited by Surcouf; 04-01-2021, 07:17 AM.Surcouf
A nostalgic PO - Previously "Almost There" - Catalina 27 (1979)
Comment
-
-
Another way
If you can still spin the engine with the starter or even by hand do this, Since the valve is stuck in the up position cranking or spinning the cylinder through the cycles do you see the valve moving up at all? If not get an .030 feeler gage and place it between the stem and the lifter as if you were adjusting the valve and spin her through, the feeler gage should move the valve the additional .030 "up" and if it does you now have it "broken loose" so getting it looser becomes easier.
Have done this before with mostly success.
If you get it moving at all it should free up. Pay attention to the valve if it starts to move any down and then gets pushed back up even a tiny bit working it will free it then keep it lubed through the fuel for a while.
If no starter just roll the engine back and forth with the cam high spot going back and forth contacting the valve with the additional lift of the feeler gage.
Dave Neptune
Comment
-
-
Mr Wizard to the rescue again. I never thought of using a fat feeler gauge and rotating the crank to push the valve up farther to break it free. Genius!
This is the difference of a paid professional vs want-to-be-a-talented amatuer.Thanks,
Ron
Portland, OR
Comment
-
-
Okay, now I'm spending time just spraying and prodding using the suggestions above, a bit each day. I am glad I am practicing spraying with the less severe products before trying acetone mix - 'cause I'm getting stuff all over... there are so many techniques to develop. Now then, I'd still like to know if anyone can tell me what those two shiny bands are under tappet of the two valves?
Comment
-
-
Originally posted by DDO View PostOkay, now I'm spending time just spraying and prodding using the suggestions above, a bit each day. I am glad I am practicing spraying with the less severe products before trying acetone mix - 'cause I'm getting stuff all over... there are so many techniques to develop. Now then, I'd still like to know if anyone can tell me what those two shiny bands are under tappet of the two valves?
Surcouf
A nostalgic PO - Previously "Almost There" - Catalina 27 (1979)
Comment
-
-
Ok, now I'm all caught up on all the suggestions... and no progress on the stuck valve using the various methods. So I pulled the head off. Would have pulled the thermostat for its annual exam anyway and who doesn't want a chance to paint the alternator bracket? Odd, I thought it would be more difficult but all the nuts came off and I easily lifted it straight up after a few screwdriver "wedges" placed and wiggled. Did not expect that! Someone has worked on this engine before me - but I've had it since 2005. The nuts were not all the same size, right side 9/16 but left side smaller and with washers. (I'm so confused...) I took a photo pre-cleanup for you. Black sooty everywhere but not seawater damage etc.
Comment
-
-
Comment