Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Discussion Topics > Ignition System

Reply
 
Thread Tools Display Modes
  #1   IP: 159.108.102.206
Old 06-07-2017, 04:53 PM
JimF JimF is offline
Senior Member
 
Join Date: Jun 2007
Posts: 19
Thanks: 9
Thanked 3 Times in 3 Posts
There was a reference to "lubing the advance" - how & where

Hi,

I thought I finally knew pretty much everything needed to maintain the lump of rusty iron (A4) in my boat but in another thread about EI ( I do have EI) I saw a reference to still needing to lube the advance weights or they rust. What is the procedure for that, does the distrubutor need to e removed to do it? Where are the advance weights? How often does it need to be done?

Thanks in advance

Jim
Reply With Quote
  #2   IP: 24.152.132.65
Old 06-07-2017, 05:05 PM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
The distributor can stay in the engine which is preferred to conserve the timing. Remove the distributor cap, remove the rotor, remove the magnetic EI collar, remove the round flat plate that holds the EI module. You'll find the centrifugal advance weights underneath the flat plate with small springs on them. Make sure they move freely by hand and lubricate.

How often? It varies from boat to boat, climate to climate but the more often, the better. I'd guess annually would be a place to start. Next year if they're still moving well, still rust free and oily you can extend the interval. Over time you'll establish the proper interval for your conditions.
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others
Reply With Quote
The Following 3 Users Say Thank You to ndutton For This Useful Post:
Administrator (06-07-2017), Ando (04-12-2020), JimF (06-08-2017)
  #3   IP: 159.108.102.206
Old 06-08-2017, 08:47 AM
JimF JimF is offline
Senior Member
 
Join Date: Jun 2007
Posts: 19
Thanks: 9
Thanked 3 Times in 3 Posts
further question - what to lube advance weights with

I have sili Kroil, or regular kroil, 3 in 1 oil, or should it be some kind of grease?
Reply With Quote
  #4   IP: 99.30.185.198
Old 06-08-2017, 10:01 AM
thatch thatch is offline
Afourian MVP
 
Join Date: Dec 2009
Location: Santa clarita, Ca.
Posts: 1,079
Thanks: 235
Thanked 257 Times in 138 Posts
A quick check on the operation of the advance weights and springs can be made by removing the distributor cap and then by rotating the rotor "clockwise". If things are freed-up, the rotor will move and then return to it's original position when released. This movement will be about 17 degrees, or about 1/2 hour on a clock face.
Tom
Reply With Quote
The Following 3 Users Say Thank You to thatch For This Useful Post:
Ando (04-12-2020), ArtJ (04-28-2022), Peter (06-08-2017)
  #5   IP: 98.171.161.182
Old 06-08-2017, 01:03 PM
JOHN COOKSON JOHN COOKSON is offline
Afourian MVP, Professor Emeritus
 
Join Date: Nov 2008
Posts: 3,500
Thanks: 54
Thanked 855 Times in 629 Posts
Any light machine oil works fine. I use 3in1 oil on the fly weights. The weights need to move freely so grease on them will not result in optimal operation.
You can check their operation for free movment if you have a feel for it. It is possible to sort of brut strength the rotor and have the rotor pop back to no advance and think everything is OK.
In my pre forum days I would check the advance operation yearly by twisting the rotor. Everything seemed to be OK for years. One year I took the breaker plate off. What a mess. One spring was gone due to rust. There was rust between the weights and the distributor. After I got new springs and cleaned up the rust the engine ran much much better. It was like a major tune up.

TRUE GRIT
Reply With Quote
The Following 4 Users Say Thank You to JOHN COOKSON For This Useful Post:
Ando (04-12-2020), GregH (01-19-2018), JimF (06-08-2017), tmcdonagh (05-21-2019)
  #6   IP: 99.30.185.198
Old 06-08-2017, 01:26 PM
thatch thatch is offline
Afourian MVP
 
Join Date: Dec 2009
Location: Santa clarita, Ca.
Posts: 1,079
Thanks: 235
Thanked 257 Times in 138 Posts
John is completely correct in stating that bad things could be going on under the breaker plate, despite being able to move the rotor. This test is meant to determine if the distributor is frozen or not. I have a feeling that there are many A4 distributors out there that are basically "not advancing" and whose owners have "power tuned" their engines and assummed that all was well. A well tuned A4 will idle smoothly and put out good power through the entire RPM range, much like a sewing machine.
Tom
Reply With Quote
The Following 4 Users Say Thank You to thatch For This Useful Post:
Administrator (06-08-2017), Bratina (06-08-2017), Dave Neptune (06-08-2017), JimF (06-08-2017)
  #7   IP: 12.42.137.2
Old 06-08-2017, 10:51 PM
roadnsky's Avatar
roadnsky roadnsky is offline
Afourian MVP
 
Join Date: Dec 2008
Location: Lake Mead, NV
Posts: 3,104
Thanks: 24
Thanked 467 Times in 309 Posts
Quote:
Originally Posted by thatch View Post
A quick check on the operation of the advance weights and springs can be made by removing the distributor cap and then by rotating the rotor "clockwise". If things are freed-up, the rotor will move and then return to it's original position when released. This movement will be about 17 degrees, or about 1/2 hour on a clock face.
Tom
Pic of what Tom is talking about...
Attached Images
  
__________________
-Jerry

'Lone Ranger'

1978 RANGER 30
Reply With Quote
The Following 3 Users Say Thank You to roadnsky For This Useful Post:
GregH (01-19-2018), Marty Levenson (06-09-2017), zialater (06-12-2017)
  #8   IP: 99.30.185.198
Old 06-08-2017, 11:39 PM
thatch thatch is offline
Afourian MVP
 
Join Date: Dec 2009
Location: Santa clarita, Ca.
Posts: 1,079
Thanks: 235
Thanked 257 Times in 138 Posts
Although Jerry's excellent photos show the innards of a distributor that is considerably different from a Delco or a Prestolite, the principals still apply.
Okay Jerry, I'll bite, what brand of dist is it, a Pertronix?
Tom
Reply With Quote
  #9   IP: 174.227.7.191
Old 06-10-2017, 12:33 PM
roadnsky's Avatar
roadnsky roadnsky is offline
Afourian MVP
 
Join Date: Dec 2008
Location: Lake Mead, NV
Posts: 3,104
Thanks: 24
Thanked 467 Times in 309 Posts
Talking BINGO!

Quote:
Originally Posted by thatch View Post
Although Jerry's excellent photos show the innards of a distributor that is considerably different from a Delco or a Prestolite, the principals still apply.
Okay Jerry, I'll bite, what brand of dist is it, a Pertronix?
Yep. Pertronix.
Sorry didn't realize we were discussing the Delco or Prestolite.
But yeah, same principle...
Attached Images
   
__________________
-Jerry

'Lone Ranger'

1978 RANGER 30
Reply With Quote
  #10   IP: 206.125.176.3
Old 06-12-2017, 10:54 AM
sastanley's Avatar
sastanley sastanley is offline
Afourian MVP
 
Join Date: Sep 2008
Location: Solomons, MD
Posts: 7,016
Thanks: 1,134
Thanked 600 Times in 442 Posts
Exclamation Delco Dizzy

Oh good..a topical thread for me.

This winter I lubed up the weights with MMO and put on new springs. Everything seemed to be operating as expected.

But now, I think my Delco dizzy shaft is getting stuck "advanced". The engine starts running like crap after about 30-40 minutes and I pulled the cap & plate to find a weight stuck out extended, and I can't rotate the rotor the 17° clockwise being discussed here..like it is already in that position. I thought I'd freed it up by adding a little oil under the felt thingie, but a subsequent test run the next day revealed the same problem 30 minutes later.

I think I understand the basic concept, and I assume there are two shafts at work here..one spins inside the other up to 17°. An education would be appreciated.

Is the lubing of the weights and the lubing of the shaft itself two separate things, as I think it is? What are some tips to get the two shafts to stop freezing up on each other?

Help..the engine is almost unusable in this state.
__________________
-Shawn
"Holiday" - '89 Alura 35 #109
"Twice Around" - '77 C-30, #511 with original A-4 & MMI manifold - SOLD! (no longer a two boat owner!!)
http://www.moyermarine.com/forums/signaturepics/sigpic3231_6.gif

Last edited by sastanley; 06-12-2017 at 10:58 AM.
Reply With Quote
  #11   IP: 24.145.95.201
Old 06-12-2017, 11:02 AM
Administrator's Avatar
Administrator Administrator is offline
MMI Webmaster
 
Join Date: Oct 2004
Location: Chestertown, MD (Langford Creek)
Posts: 2,198
Thanks: 1,335
Thanked 365 Times in 182 Posts
New springs....

Another "It can't be..."?

Bill
Reply With Quote
  #12   IP: 206.125.176.3
Old 06-12-2017, 11:25 AM
sastanley's Avatar
sastanley sastanley is offline
Afourian MVP
 
Join Date: Sep 2008
Location: Solomons, MD
Posts: 7,016
Thanks: 1,134
Thanked 600 Times in 442 Posts
Bill, I know..but if you area alluding to the old thing we've been 'round and 'round about, I do not think it is the coil, & the springs were MMI issue earlier this spring.

It does not quit, but last evening I was literally sitting there with my hand on the distributor adjusting the timing on the fly as the engine missed and surged and carried on to keep it running while Laura was at the helm. I could generally keep it running at a high idle (1,500 RPM) while coasting out of gear to slow down for slip entry. Sometimes it would occasionally stall at lower RPM, but fired right back up..and, once I 'politely' force the rotor/shaft/weights back to their normal positions, she'll idle just fine. But, when I throttled up enough to swing those weights out (and I don't know exactly where that point is), that's when I seem to get into trouble. I also wonder if it is heat related..when the parts are cold they seem to be free, but when they get hot and expand, maybe they are getting stuck.

I am pretty sure the advance mechanism is the issue, and that is what I am focusing on. The same buddy that used to own/ride Harley's and helped me free the weights up on the sea wall in Cambridge a couple years ago, came down and drank all my beer.....I mean helped me with it this weekend and he agrees with my theory. We thought we'd fixed it with the lubing exercise in post #10.

My step-dad is pretty smart on this stuff too, he's offered to come by and poke his nose in it..but it is like eleventy-billion degrees this week.

edit - so, while sitting in my office and I am not staring at this thing, I guess my question is what is the relationship between the weights and shaft(s) and springs..can someone explain how they all work in more detail, so I know what I am trying to 'free up'?
__________________
-Shawn
"Holiday" - '89 Alura 35 #109
"Twice Around" - '77 C-30, #511 with original A-4 & MMI manifold - SOLD! (no longer a two boat owner!!)
http://www.moyermarine.com/forums/signaturepics/sigpic3231_6.gif

Last edited by sastanley; 06-12-2017 at 11:42 AM.
Reply With Quote
  #13   IP: 99.30.185.198
Old 06-12-2017, 11:48 AM
thatch thatch is offline
Afourian MVP
 
Join Date: Dec 2009
Location: Santa clarita, Ca.
Posts: 1,079
Thanks: 235
Thanked 257 Times in 138 Posts
Hi Shawn, You are correct in assumming that there are inner and outer parts that are rotating against each other. The inner shaft goes from the gear at the bottom of the dist to the top where the rotor sits. The other is a plate that holds the cage containing the weights and springs. At the point where these parts rub together it is assummed that there will be enough engine oil working it's way up to that area to keep things rotating. First I would try, after removing the rotor, magnetic ring and the EI mounting plate, dripping some light weight (3 in one) oil along the center shaft which should work it's way to the friction point. If this does not do the trick, then the next step would be to remove the entire unit for a proper "bench" cleaning and lubing. Before removing my distributors, I rotate the engine so that the rotor is pointing at a "known" point and then I put marks at on the base of the dist and on the block so that I can put things back in their original positions.
Tom
Reply With Quote
  #14   IP: 206.125.176.3
Old 06-12-2017, 12:11 PM
sastanley's Avatar
sastanley sastanley is offline
Afourian MVP
 
Join Date: Sep 2008
Location: Solomons, MD
Posts: 7,016
Thanks: 1,134
Thanked 600 Times in 442 Posts
Tom, thanks for the explanation.

I think the plan will be to take the whole thing off the motor and work on it in the air conditioned garage. Thanks for the tip too, I always hand crank it to TDC before removing the distributor.

I'll report back...the biggest issue will be getting enough time to run it for 30-45 minutes again.
__________________
-Shawn
"Holiday" - '89 Alura 35 #109
"Twice Around" - '77 C-30, #511 with original A-4 & MMI manifold - SOLD! (no longer a two boat owner!!)
http://www.moyermarine.com/forums/signaturepics/sigpic3231_6.gif
Reply With Quote
  #15   IP: 99.30.185.198
Old 06-12-2017, 12:49 PM
thatch thatch is offline
Afourian MVP
 
Join Date: Dec 2009
Location: Santa clarita, Ca.
Posts: 1,079
Thanks: 235
Thanked 257 Times in 138 Posts
Since you're going to pull the entire unit, I'd go the rest of the way and remove the drive gear and the center shaft. It'll be interesting seeing what you find.
Tom
Reply With Quote
  #16   IP: 206.125.176.3
Old 06-12-2017, 12:56 PM
sastanley's Avatar
sastanley sastanley is offline
Afourian MVP
 
Join Date: Sep 2008
Location: Solomons, MD
Posts: 7,016
Thanks: 1,134
Thanked 600 Times in 442 Posts
Yes, that is what my step-father recommended. He said we should find a couple roll pins holding all the parts togther. I recall one down on bottom of the shaft holding the gear on, but am not sure exactly how the rest of it separates, but that is what the experts like him are for...gotta surround yourself with smart people!

I'll be sure to take some pics as I've never seen the distributor disassembled farther than the removing the weights.

And, I get another chance to use my punch set!
__________________
-Shawn
"Holiday" - '89 Alura 35 #109
"Twice Around" - '77 C-30, #511 with original A-4 & MMI manifold - SOLD! (no longer a two boat owner!!)
http://www.moyermarine.com/forums/signaturepics/sigpic3231_6.gif
Reply With Quote
  #17   IP: 99.30.185.198
Old 06-12-2017, 01:15 PM
thatch thatch is offline
Afourian MVP
 
Join Date: Dec 2009
Location: Santa clarita, Ca.
Posts: 1,079
Thanks: 235
Thanked 257 Times in 138 Posts
One rolled pin through the gear is what holds things together. There are washers/spacers between the gear and housing, just make sure that they go back in the same order.
Tom
Reply With Quote
The Following User Says Thank You to thatch For This Useful Post:
sastanley (06-12-2017)
  #18   IP: 98.171.161.182
Old 06-12-2017, 01:56 PM
JOHN COOKSON JOHN COOKSON is offline
Afourian MVP, Professor Emeritus
 
Join Date: Nov 2008
Posts: 3,500
Thanks: 54
Thanked 855 Times in 629 Posts
Quote:
Originally Posted by sastanley View Post
But now, I think my Delco dizzy shaft is getting stuck "advanced". The engine starts running like crap after about 30-40 minutes and I pulled the cap & plate to find a weight stuck out extended, and I can't rotate the rotor the 17° clockwise being discussed here..like it is already in that position. I thought I'd freed it up by adding a little oil under the felt thingie, but a subsequent test run the next day revealed the same problem 30 minutes later.
If you figure out why the engine "started running like crap after 30-45 minutes" also "the same problem 30 minutes later" let us know.
As I recall you reported problems with the advance a few months ago.
Agree that it is time to remove the dizzy and get to the root of the problem. If you could get some pictures of the problem once you get it apart it would be helpful for a distributor green horn like me.

TRUE GRIT
Reply With Quote
  #19   IP: 206.125.176.3
Old 06-12-2017, 03:19 PM
sastanley's Avatar
sastanley sastanley is offline
Afourian MVP
 
Join Date: Sep 2008
Location: Solomons, MD
Posts: 7,016
Thanks: 1,134
Thanked 600 Times in 442 Posts
Sure thing John...as mentioned, I thought you really only need to lube the weights (which I did over the winter with new springs), but now I am learning the two shafts can also bind up on each other, which I think is what is happening here. I'll be sure to snap some fotos!
__________________
-Shawn
"Holiday" - '89 Alura 35 #109
"Twice Around" - '77 C-30, #511 with original A-4 & MMI manifold - SOLD! (no longer a two boat owner!!)
http://www.moyermarine.com/forums/signaturepics/sigpic3231_6.gif
Reply With Quote
  #20   IP: 24.145.95.201
Old 06-12-2017, 04:19 PM
Administrator's Avatar
Administrator Administrator is offline
MMI Webmaster
 
Join Date: Oct 2004
Location: Chestertown, MD (Langford Creek)
Posts: 2,198
Thanks: 1,335
Thanked 365 Times in 182 Posts
Quote:
Bill, I know..but if you area alluding to the old thing we've been 'round and 'round about, I do not think it is the coil, & the springs were MMI issue earlier this spring.
I was alluding to something having to do with changing the springs.

Bill
Reply With Quote
  #21   IP: 71.178.84.173
Old 06-12-2017, 10:31 PM
sastanley's Avatar
sastanley sastanley is offline
Afourian MVP
 
Join Date: Sep 2008
Location: Solomons, MD
Posts: 7,016
Thanks: 1,134
Thanked 600 Times in 442 Posts
Oh, OK, Bill..well then I was confused. I had full confidence in the springs.

Anyway, so my step-father came over and we futzed with the dizzy. He is pretty confident the issue was some foreign matter in between the two shafts binding it up. We found some scoring on the outer shaft that we cleaned up with some 600 grit wrapped around a pencil. We also used the 600 grit to polish the inner shaft, which showed rust and brown contamination.
Tom, we ended up not needing to remove the gear and inner shaft from the housing..all the problems appeared to be where the two shafts hang out together inside the cam lobes.

All re-assembled, and as soon as I reinstall the dizzy, it will be ready for a test drive on Wednesday evening.

Thanks to my step-father, Pete, for being the hand model
Attached Images
  
__________________
-Shawn
"Holiday" - '89 Alura 35 #109
"Twice Around" - '77 C-30, #511 with original A-4 & MMI manifold - SOLD! (no longer a two boat owner!!)
http://www.moyermarine.com/forums/signaturepics/sigpic3231_6.gif
Reply With Quote
The Following User Says Thank You to sastanley For This Useful Post:
chapster5 (06-13-2017)
  #22   IP: 99.30.185.198
Old 06-13-2017, 11:20 AM
thatch thatch is offline
Afourian MVP
 
Join Date: Dec 2009
Location: Santa clarita, Ca.
Posts: 1,079
Thanks: 235
Thanked 257 Times in 138 Posts
Oops

After looking at Shawn's clean-up of his distributor, I had concerns about how the Delco unit was arranged. In my Universal parts book dated 8/79, the assembly diagram shows the drive shaft and top spring mount plate as being one piece, just like other V8 types of Delco units, thus reguiring removal of the bottom gear for cleaning and lubing. Apparantly, at some point the design changed to what Shawn has. I also took apart my spare distributor and found it to be just like Shawn's. I guess my next question would be to Don, asking if he knows about when there was a design change, if there was one.
Tom
Reply With Quote
  #23   IP: 74.99.165.52
Old 06-13-2017, 12:22 PM
Don Moyer's Avatar
Don Moyer Don Moyer is offline
 
Join Date: Oct 2004
Posts: 2,811
Thanks: 0
Thanked 183 Times in 124 Posts
Oops

Tom, relying on a Delco distributor in my lower desk drawer, the shaft does connect to a plate on top onto which the flyweight assembly attaches, so you would have to remove the drive gear to remove the shaft. I don't know of any other variations of this particular distributor.

Many years ago, in hoping to find some other application for our distributor, I called Delco customer service with our Delco part number (1110-546-8-B16) and asked what applications used this particular distributor (not telling her I was working on an Atomic 4). The nice lady on the other end of the line came back in a few minutes saying she was confused because there was only one line in her part numbering document for that part number and it was for a Universal Atomic 4. She suspected a misprint of some kind. I thanked her and told her that her information was unfortunately correct.

One more point for Shawn in passing; since you're removing the entire flyweight assembly, notice that it's possible to get the upper shaft (with the two arms on the bottom which attach to the springs) installed backwards. This will have the advance mechanism retarding the ignition on increasing RPM instead of advancing it. Just be sure to check that the rotor spring loads in a clockwise direction before you complete the assembly. If not, simply turn the upper shaft 180 degrees so that the indexing pins in the bottom of the arm go into the holes in the plate again but rotated 180 degrees. Don
Reply With Quote
The Following 3 Users Say Thank You to Don Moyer For This Useful Post:
Ando (04-12-2020), ArtJ (04-28-2022), sastanley (06-13-2017)
  #24   IP: 206.125.176.3
Old 06-13-2017, 02:13 PM
sastanley's Avatar
sastanley sastanley is offline
Afourian MVP
 
Join Date: Sep 2008
Location: Solomons, MD
Posts: 7,016
Thanks: 1,134
Thanked 600 Times in 442 Posts
Thumbs up

Don thanks for the explanation. My stepfather worked for VW for 50+ years before retiring, which is why I called him in for reinforcements after my failed attempt to fix this issue in situ this weekend. Stuff like this is right up his alley!

I mentioned to him that some part of the assembly related to the advance weights could be put in backwards, but I wasn't quite sure which part, and it always seemed to be correct, but I wasn't 100% sure. After he examined it for about 30 seconds, he suddenly smiled and spun the shaft and showed me exactly what you explained..if you put the upper shaft in wrong, the indexing pin on the bottom side is in the wrong hole and doesn't work correctly.

Thanks again for the heads up.
__________________
-Shawn
"Holiday" - '89 Alura 35 #109
"Twice Around" - '77 C-30, #511 with original A-4 & MMI manifold - SOLD! (no longer a two boat owner!!)
http://www.moyermarine.com/forums/signaturepics/sigpic3231_6.gif
Reply With Quote
The Following User Says Thank You to sastanley For This Useful Post:
Ando (04-12-2020)
  #25   IP: 99.30.185.198
Old 06-13-2017, 03:24 PM
thatch thatch is offline
Afourian MVP
 
Join Date: Dec 2009
Location: Santa clarita, Ca.
Posts: 1,079
Thanks: 235
Thanked 257 Times in 138 Posts
Don and Shawn, Thanks for helping to sort out the confusion I had over these distributors. Also, I wonder how many people have reversed the top plate and gone nuts trying to figure out what they've done. I'll be careful putting mine back together.
Tom
Reply With Quote
The Following User Says Thank You to thatch For This Useful Post:
Ando (04-12-2020)
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
HX Cross reference Ajax Cooling System 20 11-23-2015 03:29 PM
Champion J8C Spark Plug cross reference southcoasting Ignition System 20 04-04-2012 12:49 PM
Clogged Water Intake; future reference charles@pricefarrington.c General Interest 1 05-26-2009 05:22 PM


All times are GMT -4. The time now is 07:43 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2024 Moyer Marine Inc.

All Rights Reserved