Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Discussion Topics > Overhaul

Reply
 
Thread Tools Display Modes
  #1   IP: 99.55.124.54
Old 04-26-2020, 12:41 AM
rkohl44 rkohl44 is offline
Senior Member
 
Join Date: Feb 2017
Location: Northern California
Posts: 56
Thanks: 16
Thanked 7 Times in 5 Posts
Low compression - next steps?

Hi All,

My engine has never been "peppy" and it usually hesitates as I increase throttle. I finally completed the 2 stage compression test with the following results. Both were with a cold engine. Test 2 was done after a Tbsp of motor oil was inserted into each cylinder.

Test 1: Cylinder 1: 65 2: 50 3: 60 4: 25
Test 2: Cylinder 1: 90 2: 90 3: 80 4: 50

Remarkably higher results, which indicates "worn rings or valve guides."

More info:

I completed the block pressure test and it held 15 psi for 30 minutes. It dropped to 14 psi after about 45 minutes. I'm not convinced my test equipment (the HD pressure gauge, hose barb and plug) wasn't the source of the leak.

Spark is pale yellow, but the coil checks out fine. I do have an ammeter on the original wiring. The boat is a 1982 Catalina 30, so you know how nasty the wiring is. Batteries are new, EI and a new alternator were installed 3 years ago. Carburetor was rebuilt a month ago. Exhaust was rebuilt 2 years ago. It usually starts without too much difficulty when cold. When hot, it often needs starter fluid to convince it to go.

Here is a clip of the mighty beast running (and dying): Engine running

Since I have owned the boat (4 years now), I have been religious about 1. MMO in the fuel, 2. Running the engine for 10-15 minutes at least monthly.



Questions:
Should I repeat the block pressure test?

Would removing the ammeter get me to the desired "snappy blue spark"? (and would this have any influence on the lack of peppiness?)

How does the engine sound? Is the air sucking sound normal as throttle increases? (My A-4 is the only one I've heard run in person.)

Next steps? (Call Ken and order a short block? Pull it out and fix it? Fix it in place?)

How much overhaul can I do on a Catalina 30 in place? I've seen a lot done, but not sure if rings would be possible with the boat in the water.

I feel like I'm stepping up to the big leagues. Thanks for any/all guidance!

Last edited by rkohl44; 04-26-2020 at 12:45 AM. Reason: add more details
Reply With Quote
  #2   IP: 174.255.136.76
Old 04-26-2020, 01:21 AM
Ando's Avatar
Ando Ando is offline
Senior Member
 
Join Date: Jul 2019
Location: San Pedro, CA
Posts: 247
Thanks: 333
Thanked 58 Times in 38 Posts
Did you get the correct carb rebuild kit? I ask bc I ordered the rebuild kit for an early model carb when I should’ve ordered the rebuild kit for the late model carb. The valves are very different (as well as the gasket) but thankfully the threads are the same for all the valves. My two cents. How long since you replaced the fuel filter, btw?
Reply With Quote
  #3   IP: 67.169.215.221
Old 04-26-2020, 01:56 AM
ronstory's Avatar
ronstory ronstory is offline
Afourian MVP
 
Join Date: Feb 2016
Posts: 404
Thanks: 106
Thanked 208 Times in 152 Posts
IMO, not great but not horrible either... and some questions.

Q1: how often a year do you get out and drive the motor pretty hard?

Q2: Any blue smoke do you get out the exhaust?

Q3: Do you have any blowby in the engine compartment after running for 20-30 mins while cruising.

That said, we need to figure out why your spark is not a good blue spark.
__________________
Thanks,
Ron
Portland, OR

Last edited by ronstory; 04-26-2020 at 01:56 AM. Reason: dup signature
Reply With Quote
  #4   IP: 96.228.36.217
Old 04-26-2020, 06:43 AM
Dreadnaughty13 Dreadnaughty13 is offline
Frequent Contributor
 
Join Date: Aug 2019
Posts: 6
Thanks: 0
Thanked 0 Times in 0 Posts
Sounds like a couple of problems

Lack of throttle response may be due to one of the carburetor jets being plugged. They have released a good video of this on youtube. I would definately start here before chasing down something else

https://youtu.be/kHuemGC_PHA

As for the compression, if it's running I'm not sure I'd mess with it but there are a couple of things you could do:

1) If you've already removed the carburetor, you can pull off the valve cover on the side. Check the clearances on you valves to make sure the valves on #4 is seating all the way.
2) If there is access, you can pull the head. If the motor hasn't been broken down for several years this is going to be really hard to get off but is possible. You will need new head gaskets if you pull this off.
Reply With Quote
  #5   IP: 47.142.141.4
Old 04-26-2020, 11:44 AM
JOHN COOKSON JOHN COOKSON is offline
Afourian MVP, Professor Emeritus
 
Join Date: Nov 2008
Posts: 3,500
Thanks: 54
Thanked 855 Times in 629 Posts
Quote:
Originally Posted by ronstory View Post
That said, we need to figure out why your spark is not a good blue spark.
The first thing I would do is take a voltage reading at coil +.

ex TRUE GRIT
Reply With Quote
  #6   IP: 72.69.36.126
Old 04-26-2020, 06:57 PM
tenders tenders is offline
Afourian MVP
 
Join Date: May 2007
Location: Harlem YC, City Island, NY
Posts: 1,439
Thanks: 46
Thanked 259 Times in 170 Posts
The engine doesn't sound horrible in the video. Well, except for the dying part. Which could be due to a less-than-optimal air/fuel mixture, an idle speed that's too low, or a clog/dirty jets in the carb - basically the FUEL part of the FUEL/COMPRESSION/SPARK triad of necessity.

On the COMPRESSION part, when it's running, put some rubber gloves on and pull off one spark plug boot at a time. The engine's RPMs should diminish in an obvious way, indicating that each cylinder is firing more or less correctly. (Then put the boot back on and pull off the next one.) If #4 doesn't change, you have a pretty good indication that cylinder's low compression is problematic.

Re: SPARK, agree, get us some voltage readings across that coil. This isn't a great time to surgically remove the ammeter, but once this gets cured I would do that. It just doesn't give you enough useful information to justify the long path it makes all the juice follow.
Reply With Quote
The Following User Says Thank You to tenders For This Useful Post:
ronstory (04-27-2020)
  #7   IP: 67.169.215.221
Old 04-27-2020, 12:57 AM
ronstory's Avatar
ronstory ronstory is offline
Afourian MVP
 
Join Date: Feb 2016
Posts: 404
Thanks: 106
Thanked 208 Times in 152 Posts
Quote:
Originally Posted by tenders View Post
The engine doesn't sound horrible in the video. Well, except for the dying part.
This made me smile. Thank-you.
__________________
Thanks,
Ron
Portland, OR
Reply With Quote
  #8   IP: 99.55.124.54
Old 04-27-2020, 09:16 AM
rkohl44 rkohl44 is offline
Senior Member
 
Join Date: Feb 2017
Location: Northern California
Posts: 56
Thanks: 16
Thanked 7 Times in 5 Posts
Ando: Yes, correct carb kit was installed. New fuel filter this year.

ronstory: Q1: motor not not frequently driven hard for extended periods. New marina only takes 10-15 minutes to get to sailing conditions.
Q2: no blue smoke
Q3: haven't noticed any blowby in engine compartment

Dreadnaughty13: carb was just rebuilt. looks like there are other steps before checking valves

John Cookson: I took a voltage reading at the coil within the last 2 months and wrote it down in my logbook. Unfortunately, it's on the boat. Will report back next time I'm there. As I recall, it was what it was supposed to be but can't be 100% certain.

tenders: carb was just rebuilt and I have a polishing filter. I'll perform the rubber glove spark plug boot removal test next time I'm at the boat. I don't have a tachometer installed, but I'd imagine you would suggest I at least get a handheld one. I'll leave the ammeter in place.

Thanks all. More testing to be done and will report back when complete.
Reply With Quote
The Following User Says Thank You to rkohl44 For This Useful Post:
Ando (04-27-2020)
  #9   IP: 67.169.215.221
Old 04-27-2020, 05:28 PM
ronstory's Avatar
ronstory ronstory is offline
Afourian MVP
 
Join Date: Feb 2016
Posts: 404
Thanks: 106
Thanked 208 Times in 152 Posts
Points for closing out the homework, in a home schooling environment.

As for the compression, you would need to preform a leakdown test to try and discern the cause or causes. But the fact that adding oil substantially increased the compression likely means your rings that are not doing their job effectively.

IMO, if engine is not run much you can get a lot gunk on rings over time. My 2nd A4 was from from a fresh water lake that was only run for very short periods to and from the slip. It needed several MMO treatments of an ounce or so in each cylinder when I left the boat to unstick the rings so it soaked the couple of weeks we were away from the boat.

It's *much* better now. When I first ran it under load high load to test the repitch of the prop... I complete filled the cabin with blowby. Now with MMO treatment and running the motor, very little blowby. Now if it only had oil consistent oil pressure when hot, the motor would be great.

Give the MMO treatment a try and then retest compression in a month or two.
__________________
Thanks,
Ron
Portland, OR
Reply With Quote
The Following 3 Users Say Thank You to ronstory For This Useful Post:
Ando (04-27-2020), edwardc (04-28-2020), Surcouf (04-27-2020)
  #10   IP: 99.55.124.54
Old 04-28-2020, 12:13 AM
rkohl44 rkohl44 is offline
Senior Member
 
Join Date: Feb 2017
Location: Northern California
Posts: 56
Thanks: 16
Thanked 7 Times in 5 Posts
ronstory: in this case, the MMO treatment is exactly what? I believe it to be squirt MMO into each low compression cylinder(s) and let it soak. Repeat. Repeat. Repeat...

correct?
Reply With Quote
  #11   IP: 172.58.19.221
Old 05-02-2020, 02:55 PM
rkohl44 rkohl44 is offline
Senior Member
 
Join Date: Feb 2017
Location: Northern California
Posts: 56
Thanks: 16
Thanked 7 Times in 5 Posts
Quote:
Originally Posted by JOHN COOKSON View Post
The first thing I would do is take a voltage reading at coil +.

ex TRUE GRIT
coil + reads 13.8
Reply With Quote
  #12   IP: 172.58.75.136
Old 05-02-2020, 03:32 PM
rkohl44 rkohl44 is offline
Senior Member
 
Join Date: Feb 2017
Location: Northern California
Posts: 56
Thanks: 16
Thanked 7 Times in 5 Posts
Quote:
Originally Posted by tenders View Post
On the COMPRESSION part, when it's running, put some rubber gloves on and pull off one spark plug boot at a time. The engine's RPMs should diminish in an obvious way, indicating that each cylinder is firing more or less correctly. (Then put the boot back on and pull off the next one.) If #4 doesn't change, you have a pretty good indication that cylinder's low compression is problematic.
RPM decreased dramatically when #1 #2 and #3 were removed.
RPM did not change at all when #4 was removed.
Reply With Quote
  #13   IP: 67.169.215.221
Old 05-02-2020, 05:25 PM
ronstory's Avatar
ronstory ronstory is offline
Afourian MVP
 
Join Date: Feb 2016
Posts: 404
Thanks: 106
Thanked 208 Times in 152 Posts
Quote:
Originally Posted by rkohl44 View Post
ronstory: in this case, the MMO treatment is exactly what? I believe it to be squirt MMO into each low compression cylinder(s) and let it soak. Repeat. Repeat. Repeat...

correct?
Correct. Just let it sit and longer is better.
__________________
Thanks,
Ron
Portland, OR
Reply With Quote
  #14   IP: 99.55.124.54
Old 05-03-2020, 01:30 PM
rkohl44 rkohl44 is offline
Senior Member
 
Join Date: Feb 2017
Location: Northern California
Posts: 56
Thanks: 16
Thanked 7 Times in 5 Posts
more info: sometimes oil pools around the top of #4 spark plug

does this indicate worn rings, or valve issues? both? neither?
Reply With Quote
  #15   IP: 47.142.128.25
Old 05-03-2020, 08:59 PM
JOHN COOKSON JOHN COOKSON is offline
Afourian MVP, Professor Emeritus
 
Join Date: Nov 2008
Posts: 3,500
Thanks: 54
Thanked 855 Times in 629 Posts
Quote:
Originally Posted by rkohl44 View Post
RPM decreased dramatically when #1 #2 and #3 were removed.
RPM did not change at all when #4 was removed.
How does #4 plug look? Is it not firing because it is oil fouled or because no electricity is getting to it?
Could always try a new plug in #4 and see if it fires.

ex TRUE GRIT
Reply With Quote
The Following User Says Thank You to JOHN COOKSON For This Useful Post:
Dave Neptune (05-06-2020)
  #16   IP: 72.69.36.126
Old 05-03-2020, 10:59 PM
tenders tenders is offline
Afourian MVP
 
Join Date: May 2007
Location: Harlem YC, City Island, NY
Posts: 1,439
Thanks: 46
Thanked 259 Times in 170 Posts
Quote:
Originally Posted by rkohl44 View Post
more info: sometimes oil pools around the top of #4 spark plug

does this indicate worn rings, or valve issues? both? neither?
This has happened to me. Cause: loose plug.
Reply With Quote
  #17   IP: 67.169.215.221
Old 05-04-2020, 12:23 AM
ronstory's Avatar
ronstory ronstory is offline
Afourian MVP
 
Join Date: Feb 2016
Posts: 404
Thanks: 106
Thanked 208 Times in 152 Posts
Quote:
Originally Posted by tenders View Post
This has happened to me. Cause: loose plug.
Agree, if the plug is tight... check the plug itself for crack. Otherwise, swap plugs and see if the problem follow the plug or stays with the cylinder #4.
__________________
Thanks,
Ron
Portland, OR
Reply With Quote
  #18   IP: 99.55.124.54
Old 05-06-2020, 12:01 AM
rkohl44 rkohl44 is offline
Senior Member
 
Join Date: Feb 2017
Location: Northern California
Posts: 56
Thanks: 16
Thanked 7 Times in 5 Posts
Quote:
Originally Posted by tenders View Post
This has happened to me. Cause: loose plug.
The Manual says (page 1-8): torque value on spark plugs is 30 Ft-lbs.

My junior high metal shop class told me to put in spark plugs hand tight and then a little bit more.

I've been waaaayyy loose on my plugs if 30 is what I'm aiming for. I don't even have a torque wrench. Could this be why I have oil around the top of #4?

Last edited by rkohl44; 05-06-2020 at 12:02 AM. Reason: splngz
Reply With Quote
  #19   IP: 72.69.36.126
Old 05-06-2020, 04:47 AM
tenders tenders is offline
Afourian MVP
 
Join Date: May 2007
Location: Harlem YC, City Island, NY
Posts: 1,439
Thanks: 46
Thanked 259 Times in 170 Posts
Agree, 30 ft-lbs is too tight for our old heads. But if the plug is in fact sufficiently tight as you mention, where is the oil coming from?
Reply With Quote
  #20   IP: 99.55.124.54
Old 05-06-2020, 09:34 AM
rkohl44 rkohl44 is offline
Senior Member
 
Join Date: Feb 2017
Location: Northern California
Posts: 56
Thanks: 16
Thanked 7 Times in 5 Posts
You're right, tenders. It's coming from inside the cylinder. I'll tighten the plugs more than I have in the past and see how that changes things.

#3 sometimes has a little oil. #1 and #2 have no evidence of oil around the plugs and much better compression. All plugs have been tightened to the same degree.

I guess the underlying question is whether the low compression on #4 is related to the oil pooling around that plug. Worn rings AND loose plug combo?
Reply With Quote
  #21   IP: 155.186.124.219
Old 05-06-2020, 09:35 AM
Dave Neptune Dave Neptune is offline
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Grove, Oklahoma
Posts: 5,035
Thanks: 711
Thanked 1,289 Times in 839 Posts
Seats & metal seals

The sparkplugs the A-4 uses have a "metal crush gasket", that collapses and seals. First be sure the seat where the plug seals is clean and free of debris. Common practice with these seals is finger tight to get the seal in contact and then about a 1/4 turn. This is OK but about 20 lbs of torque should be sufficient.

Tapered type seats are much different to seal.

There should be no leaking of oil past the plug. Install a new set with proper gap and torque. You should feel the metal gasket collapse and then tighten firmly or use a torque wrench if you are unsure of your arm rating.

Also note that a loose plug won't seal very well and it won't conduct the firing of the spark to a good ground IE a weak spark. Spark needs to be blue and snappy crisp sounding.

Dave Neptune
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Valid Compression Test jkenan Troubleshooting 11 12-18-2013 09:14 PM
Another Low Compression Issue Triton106 Troubleshooting 19 09-19-2011 09:27 AM
Compression: How high is to high? Aaron B General Maintenance 8 04-21-2011 04:18 AM
High Compression? Kurt General Maintenance 4 06-17-2008 03:42 PM
Compression - Good enough, or Not High Hopes Overhaul 2 06-06-2008 10:29 PM


All times are GMT -4. The time now is 05:46 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2024 Moyer Marine Inc.

All Rights Reserved