Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Discussion Topics > Overhaul

Reply
 
Thread Tools Display Modes
  #1   IP: 138.16.128.0
Old 04-27-2017, 10:23 PM
jcwright jcwright is offline
Afourian MVP
 
Join Date: Jul 2012
Posts: 158
Thanks: 5
Thanked 98 Times in 75 Posts
Notes on Overhauling an Atomic 4

Hello Afourians.

I am writing to thank Don Moyer, MMI, and all of you for your contributions to the forum, which made it possible for me to overhaul my engine. Without the advice you have assembled here, I would never have attempted this job.

Below is a link to my notes on the overhaul, which I hope expresses my appreciation for your help.

Best regards,

Jack Wright

Note on overhauling an Atomic 4: http://bit.ly/2prGuks
Reply With Quote
The Following 4 Users Say Thank You to jcwright For This Useful Post:
Administrator (04-28-2017), Easy Rider (04-30-2017), southcoasting (04-28-2017), tenders (04-29-2017)
  #2   IP: 166.216.157.125
Old 04-28-2017, 01:51 PM
lat 64's Avatar
lat 64 lat 64 is offline
Afourian MVP
 
Join Date: Oct 2008
Location: Fairbanks, Alaska
Posts: 1,963
Thanks: 38
Thanked 240 Times in 157 Posts
Hey, great document.
It should be a good example to others.

I ran through it fairly quickly and noticed you were not sure about piston measurements.
Pistons are not round at all, but often have complicated shapes to allow for different rates thermal expansion in hotter areas during running.

The only real critical measurement for determining piston wear is the widest dimension of the piston skirt. That is at the bottom of the skirt, 90-degrees from the wrist pin axis. This is where typical(normal) wear occurs most and clearance* is smallest. This area is the bearing surface when the piston is pushed down the cylinder. This skirt-size measurement, plus clearance, is what a machinist will use to determine the size of the cylinder when fitting new pistons in a newly-bored cylinder or determining acceptable wear in an "overhaul".
Sometimes measuring at the top of the same area will get you different measurements even on a new piston.




*piston-to-cylinder wall clearance, Measured by subtracting piston diameter from cylinder diameter.

Cheers and salutations,

Russ
__________________
Whiskeyjack a '68 Columbia 36 rebuilt A-4 with 2:1

"Since when is napping doing nothing?"
Reply With Quote
The Following 2 Users Say Thank You to lat 64 For This Useful Post:
Dave Neptune (04-30-2017), jcwright (04-30-2017)
  #3   IP: 76.179.119.203
Old 04-28-2017, 04:06 PM
BunnyPlanet169's Avatar
BunnyPlanet169 BunnyPlanet169 is offline
Afourian MVP, Professor Emeritus
 
Join Date: May 2010
Location: York, ME
Posts: 952
Thanks: 25
Thanked 93 Times in 66 Posts
Quote:
Originally Posted by jcwright View Post
From the Document: "The overhaul was a case of mission creep."
Jack: Welcome to the forum, and what an epic first post!!!

Absolutely beautiful job on the engine. Nice work.

Stick around - won't you?!
__________________
Jeff


S/V Bunny Planet
1971 Bristol 29 #169
Reply With Quote
The Following User Says Thank You to BunnyPlanet169 For This Useful Post:
jcwright (04-30-2017)
  #4   IP: 72.92.234.8
Old 04-30-2017, 12:08 PM
jcwright jcwright is offline
Afourian MVP
 
Join Date: Jul 2012
Posts: 158
Thanks: 5
Thanked 98 Times in 75 Posts
Russ @Lat 64:

Thanks for the details on piston measurements. There are so many things I wished I'd known during the overhaul. In hindsight bringing my questions to the forum as they came up would have been smarter. And more fun.

Your note helps me interpret Hess' comments on this:

"Piston skirt diameter (bottom of skirt near expansion slot at right angles to pin). Note: pistons are not round when at room temperature because they are cam ground oval so they expand to round when at engine running temperature. Std: 2.560 in."

I wasn't sure how to interpret them at the time, but my (average) measurements for skirt diameter at that location were: 2.553, 2.554, 2.559, and 2.560. Hopefully I didn't make a major mistake in not getting new pistons.

Jeff @BunnyPlanet169:

Thanks for your comment.

Yes, there was a lot of mission creep here. And I had some explaining to do when the family's CFO started asking questions about rising mission cost.

Best regards,

Jack
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
For sale. Atomic 4 engine plus many parts nhoj4782 For Sale - Engines and Engine Parts 9 12-12-2014 05:36 PM
Atomic 4 without dipstick hole in block boydwest@gmail.com General Interest 15 09-11-2014 11:23 PM
Catalina Atomic 4 No Crank Problem Resolved Don Moyer Catalina 27 01-10-2013 12:20 PM
Steel frozen Atomic 4 rscaej Pearson 17 06-07-2012 02:09 PM
Evaluating Atomic 4(Newbie)?? dick auge General Interest 8 01-25-2008 05:10 PM


All times are GMT -4. The time now is 08:46 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2022, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2022 Moyer Marine Inc.

All Rights Reserved