Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Discussion Topics > General Maintenance

Reply
 
Thread Tools Display Modes
  #26   IP: 173.30.41.140
Old 12-19-2017, 08:05 PM
Ram41662 Ram41662 is offline
Senior Member
 
Join Date: Dec 2017
Location: Moline, IL
Posts: 158
Thanks: 75
Thanked 32 Times in 22 Posts
Neil, if you see the pics from inside my workshop, you should be able to catch a glimpse of my spray booth. It's only 14' x 10' x 8', so I can't get my boat in it, but I can easily fit all the parts I make before installing.
Reply With Quote
  #27   IP: 45.49.35.172
Old 09-09-2020, 08:12 PM
Ando's Avatar
Ando Ando is offline
Senior Member
 
Join Date: Jul 2019
Location: San Pedro, CA
Posts: 185
Thanks: 240
Thanked 41 Times in 28 Posts
What a cool thread

Bump any others?
Reply With Quote
  #28   IP: 137.103.82.227
Old 09-10-2020, 08:17 AM
joe_db's Avatar
joe_db joe_db is online now
 
Join Date: May 2009
Posts: 3,711
Thanks: 49
Thanked 518 Times in 381 Posts
Here you go - how to make a regulator out of a light bulb:
https://www.moyermarineforum.com/for...bulb+regulator

Reply With Quote
The Following User Says Thank You to joe_db For This Useful Post:
Ando (09-10-2020)
  #29   IP: 199.87.181.93
Old 09-10-2020, 10:20 AM
zellerj zellerj is offline
Afourian MVP
 
Join Date: May 2005
Posts: 242
Thanks: 5
Thanked 65 Times in 40 Posts
water pump gasket

To keep the paper thin water pump gasket in place while installing the screws I use small binder clips to hold the gasket on the front plate. Once the screws are started I can remove the clips and finish the job. Saves me from a lot of frustration.
Attached Images
 
__________________
Jim Zeller
1982 Catalina 30
Kelleys Island, Ohio
Reply With Quote
The Following 3 Users Say Thank You to zellerj For This Useful Post:
Ando (09-10-2020), Surcouf (09-10-2020), W2ET (09-11-2020)
  #30   IP: 155.186.124.219
Old 09-10-2020, 11:03 AM
Dave Neptune Dave Neptune is offline
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Lake Arrowhead Ca.
Posts: 4,281
Thanks: 496
Thanked 549 Times in 383 Posts
Jim, good idea with the clips and sometimes a smear of grease will do the same thing.

Dave Neptune
Reply With Quote
The Following User Says Thank You to Dave Neptune For This Useful Post:
Ando (09-10-2020)
  #31   IP: 76.237.153.161
Old 09-16-2020, 05:51 PM
brewgyver brewgyver is offline
Senior Member
 
Join Date: Jun 2014
Posts: 39
Thanks: 3
Thanked 2 Times in 1 Post
If you have to remove a machine screw that's really tight: Carefully seat the driver on the screw heat (always use a drive that fits!), then give the end of the driver a couple of whacks with a mallet or hammer, or field expedient (wrench, channel locks, etc.) This will often do the trick.
Reply With Quote
The Following 2 Users Say Thank You to brewgyver For This Useful Post:
Ando (09-16-2020), W2ET (09-16-2020)
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Please school me about this whole "bypass loop" thing wristwister Cooling System 27 01-24-2017 01:39 PM
Tricks for Propeller removal Sony2000 General Maintenance 12 03-02-2012 10:07 AM
Head nut removal tricks anyone? fvigeant Overhaul 37 06-28-2010 01:22 AM
tricks for cleaning High Hopes Cooling System 4 05-01-2009 11:14 PM
In process of rebuilding carb - Any tips or tricks? dman535 Fuel System 9 04-23-2009 03:26 PM


All times are GMT -4. The time now is 10:17 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2020, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2020 Moyer Marine Inc.

All Rights Reserved