#1
IP: 47.38.39.58
|
||||
|
||||
Can I have Ethyl if she's working?
Down here on the bayou we are about done with hurricane season. I recently bought some gas for my generator. Now I have about 15 gal extra. Due to long lines regular gas was out so I bought premium. Is there any problem with putting premium in the A4? Thanks.
|
#2
IP: 100.36.65.17
|
||||
|
||||
No harm. No benifit either.
Been a long time since I've heard premium referred to as "Ethyl"! These days, when someone refers to Ethyl, they're usually talking about alcohol.
__________________
@(^.^)@ Ed 1977 Pearson P-323 "Dolce Vita" with rebuilt Atomic-4 |
#3
IP: 47.38.39.58
|
||||
|
||||
I remember some movie from the 70's and the guy went to the "Filling Station" and told the attendant "fill'er up with Ethyl if she's working or her sister if she ain't". Don't remember the name of the movie or the actor. Funny how things like that stick with you.
|
The Following User Says Thank You to Bayou Sailor For This Useful Post: | ||
Bob N (11-30-2020) |
#4
IP: 100.36.65.17
|
||||
|
||||
Quote:
__________________
@(^.^)@ Ed 1977 Pearson P-323 "Dolce Vita" with rebuilt Atomic-4 |
The Following 2 Users Say Thank You to edwardc For This Useful Post: | ||
Bayou Sailor (11-18-2020), W2ET (11-17-2020) |
#5
IP: 217.64.127.91
|
|||
|
|||
Hii Don't remember the name of the movie or the actor. Funny how things like that stick with you COPPER SLEEVE-DOUBLE-BLACK - SLEEVECD-XXBK
. Been a long time since I've heard premium referred to as "Ethyl"! These days, when someone refers to Ethyl, they're usually talking about alcohol. Last edited by wakemutant; 11-26-2020 at 07:38 AM. |
#6
IP: 32.211.28.40
|
||||
|
||||
The 'ethyl' refers to tetraethyl lead. Added to petroleum fuels until folks started to worry about it's poisonous qualities. Leaded gas is still sold in countries such as Algeria, Iraq, N Korea.
|
#7
IP: 138.207.177.95
|
||||
|
||||
And at the airport. There was a time when I could buy car gas and stick it in some airplanes, but ethanol-gas put an end to that
|
#8
IP: 24.61.95.61
|
|||
|
|||
I saw a guy today with a spare wheel on his JEEP which
was colorfully painted Shark Removal ( SHARK TEETH LOGO ) Quint Amity Robert Shaw's family would love it!! Last edited by ArtJ; 11-20-2020 at 05:52 PM. |
#9
IP: 32.211.28.40
|
||||
|
||||
Are you sure about airport gas? I thought it was just E-zero - no alcohol. didn't think they still had lead in it.
Used to know Methyl and Ethyl well - the Ketone sisters. |
#10
IP: 47.38.39.58
|
||||
|
||||
Yeah, Ethyl was the popular one. Methyl not so much. In todays world she would need counseling and therapy.
|
#11
IP: 32.211.28.40
|
||||
|
||||
Methyl and Ethyl used to double date a lot with the Polyester boys.
|
The Following User Says Thank You to Al Schober For This Useful Post: | ||
Bayou Sailor (11-24-2020) |
#12
IP: 64.62.192.42
|
|||
|
|||
They say that kids who grew up since the ban have about a 5 point IQ advantage over those of us who grew up breathing the stuff. Dunno... I can't see it in action.
Personally, I don't put anything except ethanol-free premium into my gas cans or any of the small engines (including the A4) that are fed from them. Saves confusion and grief. |
The Following User Says Thank You to toddster For This Useful Post: | ||
sastanley (11-25-2020) |
#13
IP: 47.38.39.58
|
||||
|
||||
I don't know about that IQ thing. In the 60's and 70's we never thought about getting our nose, lip, eyelid or tongue pierced, sniffing household cleaner, eating tide pods, or many other disgusting things I hear about these days. I guess we weren't smart enough to realize how great those things could be!
|
The Following User Says Thank You to Bayou Sailor For This Useful Post: | ||
chapster5 (11-26-2020) |
#14
IP: 138.207.177.95
|
||||
|
||||
Quote:
Airports USED to have 2 grades, 80 and 100. The 80 octane that had little lead or maybe none. That got discontinued and now 100LL is all there is. "Low Lead" is only in contrast to the old 100/130 or 115/145 octane fuel, it has a LOT of lead in it. This really sucks for low compression airplanes designed to run on 80 octane.For a while we could run car gas, but then ethanol killed that off and now we have to use 100LL and then add TCP to the gas to prevent lead fouling of spark plugs and sticky valves. TCP is quite toxic, I am always careful handing it. So the moral of the story is I have to use one toxic chemical to fight the effects of another one because someone had the bright idea to subsidize Big Ag and require corn in gasoline |
#15
IP: 64.62.192.42
|
|||
|
|||
Well... not on purpose, anyway!
|
#16
IP: 24.15.212.17
|
|||
|
|||
Wasn't there talk on the forum years ago about A4's ideally needing leaded gas to protect valves from wear. From my view I have always added a couple of oz of "lead substitute" to every tank for the last 40+ yrs full on my 1966 A4 [MMO in the oil] Still running fine. Admittedly I haven't see it on the auto parts store shelf for a while but still have about quart left.
|
The Following User Says Thank You to Sam For This Useful Post: | ||
TimBSmith (11-25-2020) |
#17
IP: 69.250.111.245
|
||||
|
||||
Quote:
I was always using a little MMO as my 'lead substitute', until this year when I took Dave Neptune's advice and started adding synthetic 2-stroke oil at about 100:1. That is a guess. I bloop a little bit down the tube before I dump in 5 gallons 87-90 octane E-zero (the octane rating depends on the source.)
__________________
-Shawn "Holiday" - '89 Alura 35 #109 "Twice Around" - '77 C-30, #511 with original A-4 & MMI manifold - SOLD! (no longer a two boat owner!!) Last edited by sastanley; 11-25-2020 at 08:01 PM. |
#18
IP: 155.186.122.195
|
|||
|
|||
Any kind of lead substitute is a waste of money on an A-4 or any low compression engine. The lead was mainly to "cushion the valve seats" and was only necessary on higher compression engines. As performance increased and compression was raised the lead was necessary to handle the additional valve loads of more duration and lift. The setting of the valves back down on the seats is greatly (stronger valve springs) increased as performance is gained.
The lead also helped in ring wear however the newer metallurgy applied made this a moot point and again the Hi-nickel A-4 block made it unnecessary. The Hi-nickel block of the A-4 is more than stout enough for this valve seating. Back when the lead was being removed 'Harder valve seats were sold unnecessarily on low compression low HP engines however anything with HP absolutely needed the harder seats and or the lead substitute. Dave Neptune |
The Following User Says Thank You to Dave Neptune For This Useful Post: | ||
Sam (11-28-2020) |
#19
IP: 69.250.111.245
|
||||
|
||||
Thanks, Dave. I never knew why lead was there except that I was told it lubed the valves, and in the 80's when I couldn't buy leaded gas anymore, I tried (as a poor teenager) to remember to put some lead substitute in there when I remembered.
My 1237cc Civic motor made 63HP in 1978. That was probably at 5,500 RPM or so...I don't remember.. With only a 4-speed trans..she spun about 3,300 RPM at 60 MPH. I often drove faster than that trying to beat the gate closing in the high school parking lot in the morning.
__________________
-Shawn "Holiday" - '89 Alura 35 #109 "Twice Around" - '77 C-30, #511 with original A-4 & MMI manifold - SOLD! (no longer a two boat owner!!) Last edited by sastanley; 11-25-2020 at 09:24 PM. |
#20
IP: 71.215.209.38
|
||||
|
||||
Quote:
|
#21
IP: 155.186.122.195
|
|||
|
|||
Most all valves in the past set right down on the cast iron. The seats are replaceable by boring and pressing in a hardened metal seat like on aluminum heads. Once the lead was being eliminated the manufacturers installed them at the factory. There are many "unleaded" engines manufactured today without the hardened seats but not what you would call performance related engines.
I was learning my engine skills during the time lead was being eliminated. We thought it was the end all for "good motors", but how wrong we were. During those times cars were tuned every 5K miles and valve jobs were done at around 50K miles with leaded fuels and this was the norm. Also during that time there were many garages that just said every motor needs the new valve seats and they made a lot of money doing unnecessary valve seat jobs on the low compression type mild engines and they did not last much longer. And if the new seats were not installed correctly they could come loose and/or recede into to deep of a bore. The really big cammed HIPO engines would sometimes literally hammer the valve deeper into the block until a harder seat was inserted or you kept your foot out of the throttle and kept the RPM's down. A lot of the wear on the valves was also due to the lack of good engine breathing management as the technology in carbs and mechanical advance systems just could not handle the mix and timing like a modern engine with a computer doing the controlling. In an A-4 proper valve adjustment will do more for longevity than adding lead a known toxic to humans and all living creatures. Dave Neptune |
The Following 2 Users Say Thank You to Dave Neptune For This Useful Post: | ||
romantic comedy (11-28-2020), Sam (11-28-2020) |
#22
IP: 68.134.226.200
|
||||
|
||||
Quote:
Someone decided the huge amount of lead in 100/130 was bad for the environment and having 2 grades of gas was a pain, so 100LL got invented. They started with 94 octane unleaded and added enough lead to get to 100. In theory, since it had lower lead than 100/130, it would do fine in all engines. In practice some engines suffer lead fouling to varying degrees. A Cessna Cutlass is so bad it gets lead-fouled taxiing from parking to the runway if you don't taxi leaned way out. Last edited by joe_db; 11-26-2020 at 01:39 PM. |
#23
IP: 69.250.111.245
|
||||
|
||||
Interesting Joe, thanks for the info.
Incidentally, my 78 Civic had to have the head rebuilt at about 78K because of burnt valves. I sold it with 165K on it when the daughter came along and needed a four door to get the car seat in more easily.
__________________
-Shawn "Holiday" - '89 Alura 35 #109 "Twice Around" - '77 C-30, #511 with original A-4 & MMI manifold - SOLD! (no longer a two boat owner!!) Last edited by sastanley; 11-26-2020 at 08:21 PM. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
several problems, working on them 1 at a time | dive7mmwet | Troubleshooting | 10 | 08-28-2014 09:02 PM |
Will an A4 run without a working Alternator | Bryanphaas | Electrical | 20 | 04-09-2014 02:34 PM |
what are the symptoms of the advance not working? | KenVoodoo | Troubleshooting | 13 | 07-01-2012 04:53 PM |
A4 not working under load | Phil_E | Troubleshooting | 20 | 10-28-2011 08:46 AM |
Working on my A4 gives me great satisfaction | Baltimore Sailor | General Interest | 6 | 06-05-2008 04:09 PM |