Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Discussion Topics > Troubleshooting

Reply
 
Thread Tools Display Modes
  #1   IP: 173.19.42.86
Old 10-27-2020, 07:45 PM
sailhog sailhog is offline
Senior Member
 
Join Date: Apr 2009
Posts: 289
Thanks: 25
Thanked 13 Times in 9 Posts
Variable oil pressure...

Ahoy all... MY engine has about 15 hours on it since the last oil change. Until recently, the oil pressure registered right around 45 psi at start, and then slowly ticked down to around 30 psi after an hour or so of run time. On the last couple of outings, the oil pressure registers at 60 psi at start and then slowly settles down to about 20 psi after an hour or so of run time.

I'm not sure if I'm remembering this correctly, but it seems that I had read on the forum that this wildly varying oil pressure could be caused by sludge in the crankcase. To remove much of it, you could add a quart of MMO to the crankcase during an oil change, followed by running the engine for a period of time, followed by a standard oil change (without MMO).

So three questions: Is this a legitimate remedy? If not, is there a remedy out there? Or is it really not a problem?

Any comments would be much appreciated.

Thanks to you all...
Reply With Quote
  #2   IP: 100.40.58.241
Old 10-27-2020, 08:20 PM
jcwright jcwright is offline
Afourian MVP
 
Join Date: Jul 2012
Posts: 158
Thanks: 5
Thanked 99 Times in 75 Posts
When trying to figure out variable oil pressure after a rebuild I found a mechanical gauge helpful. Here is the description of the gauge in the MMI catalog:

Mechanical oil pressure gauge kit

This kit is intended to be used in the engine compartment to verify a cockpit gauge reading anytime there is a serious concern over oil pressure. The kit includes a mechanical oil pressure gauge, copper tubing and fittings to connect the gauge directly to the oil pressure port behind the flywheel housing. There is also a small needle valve in the kit to provide “snubbing” for very stable readings.
Reply With Quote
  #3   IP: 32.211.28.40
Old 10-27-2020, 09:25 PM
Al Schober's Avatar
Al Schober Al Schober is offline
Afourian MVP
 
Join Date: Jul 2009
Location: Uncasville, CT
Posts: 2,002
Thanks: 16
Thanked 578 Times in 405 Posts
Agree to check things with a mechanical gauge. Electrical senders DO wear out, and guess what - they wear most in the spot on the sender where the pressure is most of the time. Most of these senders are carbon film units and the film wears down where the wiper spends time rubbing.
Reply With Quote
  #4   IP: 138.207.177.95
Old 10-28-2020, 10:37 AM
joe_db's Avatar
joe_db joe_db is online now
Afourian MVP
 
Join Date: May 2009
Posts: 4,474
Thanks: 49
Thanked 1,026 Times in 721 Posts
FYI - I found Shell Rotella 15W40 to have less variation between hot and cold than the other oils I have tried. If you are changing oil anyway, give it a shot.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Gradually falling oil pressure clark800 Troubleshooting 91 05-18-2018 05:17 PM
Oil Pressure Adjustment Jesse Delanoy General Maintenance 59 07-24-2010 09:14 PM
Information about information and oil pressure issues Don Moyer Announcements 0 04-14-2009 08:30 AM
Oil Pressure / Rear oil seal - Next step Mark Harrington Drive Train / Propellers 6 11-24-2008 08:51 AM
Carburetor Internal Pressure Regulation Don Moyer Fuel System 2 04-12-2005 09:30 AM


All times are GMT -4. The time now is 07:57 PM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2024 Moyer Marine Inc.

All Rights Reserved