Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Discussion Topics > Troubleshooting

Reply
 
Thread Tools Display Modes
  #1   IP: 45.49.35.172
Old 06-09-2021, 09:28 PM
Ando's Avatar
Ando Ando is offline
Senior Member
 
Join Date: Jul 2019
Location: San Pedro, CA
Posts: 247
Thanks: 333
Thanked 58 Times in 38 Posts
Heat increasing, oil pressure decreasing

Recently went from raw water cooling to fresh water cooling, but the heating issue was there before the change. Not sure about the oil pressure bc in the 2.5 years of ownership, I never paid attention to it until now (ignorance is bliss).

Overheating:
Goes from less than 100 to over 180 in 15min (at idle). I’ve acid washed and dismantled and visually inspected the whole cooling system twice and see no blockages. I did remove the thermostat before each flush. Original gauges, newer senders. I have a new in box Faria gauge that I will test with the sender. I will also adjust the valve to the thermostat a quarter turn and see what happens and then a full half turn to see what happens. And I’ll report back. I also ordered a Groco 3/4” thru hull and coated it with Barnicle Barrier by Petit that I will be installing in place of the original 1/2” thru hull which I assume is calcified. Note: The fresh water cooling system does have a steel wool filter prior to the return to the hx.

Oil pressure:
Never have I ever adjusted the oil pressure valve so I’ll be doing that and reporting back.

Any other ideas, comments, suggestions are invited and appreciated

Here are pics of initial start up and 15 thereafter
Name:  1E492FE5-EE54-4BD9-AC9C-B70498A4A329.jpg
Views: 1090
Size:  143.0 KB

Name:  3E017FBB-9024-42EA-BD8F-DB122BDC364C.jpg
Views: 1010
Size:  112.2 KB
Reply With Quote
  #2   IP: 165.225.20.156
Old 06-10-2021, 03:11 AM
Surcouf's Avatar
Surcouf Surcouf is offline
Afourian MVP, Professor Emeritus
 
Join Date: May 2018
Posts: 361
Thanks: 328
Thanked 163 Times in 123 Posts
not sure I would call 180 as overheating.

See the poll, and the comments. Several owners are running at 180 especially with fresh water cooling. A4 will be happy @ 180
https://www.moyermarineforum.com/for...ead.php?t=3323

Would also depends if you sail in Maine, or in Florida
__________________
Surcouf
A nostalgic PO - Previously "Almost There" - Catalina 27 (1979)
Reply With Quote
The Following 3 Users Say Thank You to Surcouf For This Useful Post:
Ando (06-13-2021), ArtJ (09-18-2021), TimBSmith (06-29-2021)
  #3   IP: 40.140.239.18
Old 06-10-2021, 08:00 PM
Al Schober's Avatar
Al Schober Al Schober is offline
Afourian MVP
 
Join Date: Jul 2009
Location: Uncasville, CT
Posts: 2,002
Thanks: 16
Thanked 578 Times in 405 Posts
I'd remove the thermostat and see what happens.
Steel wool filter? First I've heard of such a thing. Is this a commercial item? I'd appreciate more info on it before giving judgment.
Reply With Quote
The Following User Says Thank You to Al Schober For This Useful Post:
Ando (06-13-2021)
  #4   IP: 100.36.65.17
Old 06-11-2021, 09:01 AM
edwardc's Avatar
edwardc edwardc is offline
Afourian MVP
 
Join Date: Aug 2009
Location: Laurel, MD
Posts: 2,509
Thanks: 153
Thanked 595 Times in 388 Posts
Quote:
Note: The fresh water cooling system does have a steel wool filter prior to the return to the hx.

I assume this means it is in the coolant side, not the raw water side. If so, I would remove it. There is no need for a filter in the coolant loop, and it will provide some additional obstruction. My experience with Moyer's FWC conversion kit is that it runs at 180 because it is reaching steady-state with the maximum cooling that the HX can handle. The thermostat is open all the time and is not really doing much about regulating. Any additional obstruction in the
cooling quickly results in higher temps at cruise RPM.
__________________
@(^.^)@ Ed
1977 Pearson P-323 "Dolce Vita"
with rebuilt Atomic-4

Reply With Quote
The Following 2 Users Say Thank You to edwardc For This Useful Post:
Ando (06-13-2021), ArtJ (09-18-2021)
  #5   IP: 104.174.83.118
Old 06-11-2021, 01:42 PM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
Guys, remember that the gauge temperature is with the engine at idle, out of gear (no load whatsoever) and in 61° water.
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others
Reply With Quote
The Following User Says Thank You to ndutton For This Useful Post:
Ando (06-13-2021)
  #6   IP: 73.35.200.244
Old 06-11-2021, 07:51 PM
Boat Boat is offline
Senior Member
 
Join Date: Aug 2014
Location: Kirkland, WA
Posts: 172
Thanks: 1
Thanked 14 Times in 13 Posts
180 is normal. mine takes a considerable amount of time to get up to temp. mine would never lift the needle off the peg unless i run at load for awhile. i am PNW puget sound though 54 degree water. the oil pressure on yours looks low to me though
__________________
'69 Newport 30 MKI Hull #20
Reply With Quote
The Following User Says Thank You to Boat For This Useful Post:
Ando (06-13-2021)
  #7   IP: 174.255.132.88
Old 06-13-2021, 03:51 PM
Ando's Avatar
Ando Ando is offline
Senior Member
 
Join Date: Jul 2019
Location: San Pedro, CA
Posts: 247
Thanks: 333
Thanked 58 Times in 38 Posts
Hi guys. Thanks for all the discourse. It’s comforting to hear that 180 is ok, but more comforting that running at ~150 is also reported & that’s what I’m shooting for. To that end, I will first adjust the valve at the thermostat and report back. Then, I will reopen it and remove the steel wool (yes, it’s on the fresh water side…before the hx return port) and report. Based on those readings I’ll evaluate the next steps (thermostat removal, gauge/sender issue, thermal readings of various areas of the engine etc.)

I still have to adjust the oil pressure valve.

Just gotta get back to the marina first
Reply With Quote
  #8   IP: 174.255.130.237
Old 06-15-2021, 01:31 PM
Ando's Avatar
Ando Ando is offline
Senior Member
 
Join Date: Jul 2019
Location: San Pedro, CA
Posts: 247
Thanks: 333
Thanked 58 Times in 38 Posts
Update

Overheating issue:
I adjusted the valve going to the thermostat by a quarter turn and the heat hasn’t gone above 150 for about an hour of running time. What does this tell you all? Btw, the first 15 minutes of running time were constant running and the other 45 minutes were of on and off testing of the oil pressure). Which brings me to the second part, which also has me perplexed…

Oil pressure:
No matter how I adjust the oil pressure valve (almost all the way out, half way in or all the way in), the gauge starts and stays at ~0 unless I rev the engine and then it only goes up to a bit less than 20. Any ideas?
Notes:
1. Before starting the first time, I saw that the oil valve was way way out so I turned it clockwise about two turns;
2. Then, for the next hour or so, I turned the engine off then adjusted the valve and started again to check if there was any difference for a few minutes and then off again, adjusted, check a few minutes and off again; and finally
3. when I turn the engine off, the oil pressure gauge shoots to a reading of ~30

Last edited by Ando; 06-15-2021 at 01:43 PM.
Reply With Quote
  #9   IP: 172.58.75.93
Old 06-15-2021, 01:41 PM
roadnsky's Avatar
roadnsky roadnsky is offline
Afourian MVP
 
Join Date: Dec 2008
Location: Lake Mead, NV
Posts: 3,104
Thanks: 24
Thanked 467 Times in 309 Posts
Not sure if you've already read this?

From Don in the TECH TIPS...

"In the event that you might be facing oil pressure issues that do not respond to normal adjustment (35 to 40 psi fully warmed up at normal cruise, and 20 psi or so at idle), you might want to consider the regulating valve found in the overhaul section of our online catalog before taking on any heavier maintenance on your engine. Many overhauls have been headed off by the installation of this “early model” style of valve.

Another significant aspect to the problem of regulation relates to the fact that the orifice in the block is not always perfectly centered with the centerline of the threaded shaft.

The effect of this misalignment sometimes causes oil pressure to take a nose dive during an adjustment, as the threaded shaft nears the end of its travel and forces the ball (or even the pointed shaft of early model valves) off to the side of the orifice in the block. In these cases, it’s usually necessary to use the regulating valve seatdressing tool shown in the specialty tools section of our online catalog to bevel the orifice slightly, bringing it into alignment with the shaft or ball."


You can read the entire posting HERE
__________________
-Jerry

'Lone Ranger'

1978 RANGER 30
Reply With Quote
The Following User Says Thank You to roadnsky For This Useful Post:
Ando (06-15-2021)
  #10   IP: 67.169.215.221
Old 06-15-2021, 02:09 PM
ronstory's Avatar
ronstory ronstory is offline
Afourian MVP
 
Join Date: Feb 2016
Posts: 404
Thanks: 106
Thanked 208 Times in 152 Posts
Ando--

Following Jerry's update above, when I swapped from the "modern" (eg. more cost effective, cheap) version with the ball bearing, spring and bolt/washer/nut to the original integrated cone/pin assembly, it got a few more lbs PSI. Most of it I think was due to a build-up of gunk on the pressure relief mating surface. I used one of Don's tools, but a hardwood dowel and some creative hammering/tapping will clean it up as well.

Also, I got a touch more oil pressure & stability using Indigo's external oil filter. Indigo's solution blocks the original oil regulator port and has an external oil pressure regulator built into the filter holder which make for much more convenient adjustment.

IMO, either is an improvement over the "modern" version.
__________________
Thanks,
Ron
Portland, OR
Reply With Quote
The Following User Says Thank You to ronstory For This Useful Post:
Ando (06-15-2021)
  #11   IP: 45.49.35.172
Old 06-16-2021, 11:36 PM
Ando's Avatar
Ando Ando is offline
Senior Member
 
Join Date: Jul 2019
Location: San Pedro, CA
Posts: 247
Thanks: 333
Thanked 58 Times in 38 Posts
Parts Are Ordered

Waiting the arrival of the bevel tool and the regulator. I'll keep you posted.
Reply With Quote
  #12   IP: 155.186.122.195
Old 06-17-2021, 11:25 AM
Dave Neptune Dave Neptune is online now
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Grove, Oklahoma
Posts: 5,035
Thanks: 711
Thanked 1,289 Times in 839 Posts
Ando, I'd try a mechanical gage to confirm the electric. Oil pressure would be somewhat constant and not just drop off as you state, perhaps a sender or wiring glitch.

I have never seen a filter on a cooling system only a strainer on the intake water line. I also feel "steel wool" would be a very poor choice of material and would only cause flow restrictions.

I'd really like to see a pic of this so called "filter" assembly.

Dave Neptune
Reply With Quote
The Following 2 Users Say Thank You to Dave Neptune For This Useful Post:
Ando (06-17-2021), Sam (06-29-2021)
  #13   IP: 108.185.228.107
Old 06-17-2021, 12:11 PM
Ando's Avatar
Ando Ando is offline
Senior Member
 
Join Date: Jul 2019
Location: San Pedro, CA
Posts: 247
Thanks: 333
Thanked 58 Times in 38 Posts
Quote:
Originally Posted by Dave Neptune View Post
Ando, I'd try a mechanical gage to confirm the electric. Oil pressure would be somewhat constant and not just drop off as you state, perhaps a sender or wiring glitch.

I have never seen a filter on a cooling system only a strainer on the intake water line. I also feel "steel wool" would be a very poor choice of material and would only cause flow restrictions.

I'd really like to see a pic of this so called "filter" assembly.

Dave Neptune
Awesome idea, Dave. Thx. Can you give me details on the mechanical gauge (type, cost, where to purchase one, and how to use it)? I have a gauge to test compression…will that work or is this something different?

The manual for the indigo hx calls for the placement of a temporary filter between the manifold and the hx return port. I’ll send pics of that part of the manual and the one I installed. I too was worried that it would restrict flow so I tested the unit prior to installing (using a garden hose) and I was surprised to find out that the flow was not restricted at all. I was expecting some back flow (overflow) at the connection between the unit and the hose and there was none. The connection between the two was by hand (not screwed together or anything of the like). A primitive test, but it provided enough piece of mind to put it into action.
Reply With Quote
  #14   IP: 155.186.122.195
Old 06-17-2021, 01:11 PM
Dave Neptune Dave Neptune is online now
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Grove, Oklahoma
Posts: 5,035
Thanks: 711
Thanked 1,289 Times in 839 Posts
A std oil pressure gage and a cheap one is just fine. Just like the fuel pressure gages only for higher pressure. You can mount a tee at the "sender port" or the aft port near the oil pressure adjustment.

I had both an electric on the gage panel and a mechanical one mounted on the engine so I could see it with the cover off. I cold started my engine with the cover off using a permanent remote start switch so I could see both fuel and oil readings.

Dave Neptune
Reply With Quote
The Following User Says Thank You to Dave Neptune For This Useful Post:
Ando (06-17-2021)
  #15   IP: 172.58.75.93
Old 06-17-2021, 08:11 PM
roadnsky's Avatar
roadnsky roadnsky is offline
Afourian MVP
 
Join Date: Dec 2008
Location: Lake Mead, NV
Posts: 3,104
Thanks: 24
Thanked 467 Times in 309 Posts
Quote:
Originally Posted by Ando View Post
Can you give me details on the mechanical gauge (type, cost, where to purchase one, and how to use it)?
Our host sells one HERE.
It comes with instructions and is very easy to install.
I have it and it is great for comparing to my cockpit "electric" gauge.
Attached Images
 
__________________
-Jerry

'Lone Ranger'

1978 RANGER 30
Reply With Quote
The Following User Says Thank You to roadnsky For This Useful Post:
Ando (06-18-2021)
  #16   IP: 174.255.5.109
Old 06-29-2021, 02:37 AM
Ando's Avatar
Ando Ando is offline
Senior Member
 
Join Date: Jul 2019
Location: San Pedro, CA
Posts: 247
Thanks: 333
Thanked 58 Times in 38 Posts
Quote:
Originally Posted by Dave Neptune View Post
I'd really like to see a pic of this so called "filter" assembly.

Dave Neptune
Here it is. The instructions call for PVC but I just couldn’t do it and went with brass

Name:  1BF24760-1365-4EB1-9685-906AEEDF8C46.jpg
Views: 645
Size:  107.8 KB

Name:  1C0854F1-FF46-49B7-B4E4-F9DB7273A759.jpg
Views: 653
Size:  128.4 KB

Name:  7AB8A7F4-2394-4044-9FBB-8C12B550D4AA.jpg
Views: 623
Size:  69.9 KB
Reply With Quote
The Following 2 Users Say Thank You to Ando For This Useful Post:
Dave Neptune (06-29-2021), thatch (06-29-2021)
  #17   IP: 174.255.2.201
Old 07-02-2021, 09:18 PM
Ando's Avatar
Ando Ando is offline
Senior Member
 
Join Date: Jul 2019
Location: San Pedro, CA
Posts: 247
Thanks: 333
Thanked 58 Times in 38 Posts
Question about the new parts

I received the new MMI oil pressure regulating valve and the seat dressing tool. I dressed the seat with ease and my question is whether the metal ball that came out with the old oil pressure regulating valve goes back in when using the new valve?
Reply With Quote
  #18   IP: 174.255.2.201
Old 07-02-2021, 10:28 PM
Ando's Avatar
Ando Ando is offline
Senior Member
 
Join Date: Jul 2019
Location: San Pedro, CA
Posts: 247
Thanks: 333
Thanked 58 Times in 38 Posts
Ok nevermind, I think. I put in the new one (without the metal ball) in the following order: pin, spring behind pin, washer on the bolt (between the nut and motor), and bolt (screw). I tightened it as far as I could. Upon first start (cold start), oil pressure read 30 then up to ~39 in the first minute or two and then slowly decreased to ~10 after about 30 min.

I stopped the engine, adjusted the valve by unscrewing it about a quarter of the way out and started again (hot start). It’s been ten minutes and the gauge is at a steady 8 or 9 the whole time.

Should I unscrew it more or screw it in more?

Last edited by Ando; 07-02-2021 at 10:31 PM.
Reply With Quote
  #19   IP: 108.12.235.34
Old 07-02-2021, 10:46 PM
jcwright jcwright is offline
Afourian MVP
 
Join Date: Jul 2012
Posts: 158
Thanks: 5
Thanked 99 Times in 75 Posts
Hello Ando.

You probably already have this, but if not, check this FAQ from Moyer:

https://moyermarine.com/nl12-1-17/

To increase the oil pressure, turn the adjusting screw clockwise.

Jack.
Reply With Quote
The Following User Says Thank You to jcwright For This Useful Post:
Ando (07-02-2021)
  #20   IP: 174.255.2.201
Old 07-03-2021, 12:06 AM
Ando's Avatar
Ando Ando is offline
Senior Member
 
Join Date: Jul 2019
Location: San Pedro, CA
Posts: 247
Thanks: 333
Thanked 58 Times in 38 Posts
Quote:
Originally Posted by jcwright View Post
Hello Ando.

You probably already have this, but if not, check this FAQ from Moyer:

https://moyermarine.com/nl12-1-17/

To increase the oil pressure, turn the adjusting screw clockwise.

Jack.
Great read! Thx, I hadn’t seen it before. Much appreciated.
Reply With Quote
  #21   IP: 174.255.2.201
Old 07-03-2021, 01:16 AM
Ando's Avatar
Ando Ando is offline
Senior Member
 
Join Date: Jul 2019
Location: San Pedro, CA
Posts: 247
Thanks: 333
Thanked 58 Times in 38 Posts
Ok, so based on the chart listed in the link above, my oil pressure is about 10 at idle. And it does go up when I increase the throttle. My problem now is that I don’t have an rpm gauge. So what is the relative rpm at idle? Half way engaged throttle? Full throttle? How to I find rpm??? I assume I would need that info prior to needlessly adjusting the valve right…for no reason?

Last edited by Ando; 07-03-2021 at 01:19 AM.
Reply With Quote
  #22   IP: 108.12.235.34
Old 07-03-2021, 09:33 AM
jcwright jcwright is offline
Afourian MVP
 
Join Date: Jul 2012
Posts: 158
Thanks: 5
Thanked 99 Times in 75 Posts
Hello ando.

At idle, you are probably somewhere in the 600-1000 rpm range.

A guideline from Moyer and others is to run the engine at your normal cruising speed, then aim for oil pressure of 40 psi. This would be for a fully warmed up engine.

Like others on this forum, I ran the A4 for years without a tachometer. But I don't regret installing one (see Moyer's catalog). Other options include a multimeter or timing light with a built-in rpm function. These don't require any additional boat wiring and you get the added benefit of checking timing with the strobe light.

Hope this helps some.

Jack.
Reply With Quote
The Following User Says Thank You to jcwright For This Useful Post:
Ando (07-03-2021)
  #23   IP: 174.255.2.201
Old 07-03-2021, 03:05 PM
Ando's Avatar
Ando Ando is offline
Senior Member
 
Join Date: Jul 2019
Location: San Pedro, CA
Posts: 247
Thanks: 333
Thanked 58 Times in 38 Posts
Seating Tool

I took the new regulator out and rebeveled. Why? bc I had the regulator turned clockwise as far as it would go and the reading was near 0 with the engine warm. I’m going to go get an oil pressure gauge right now from the auto parts store to verify bc this is causing too much [insert any common negative sentiment here].

In the meantime, since there’s probably no way for me to peer into the port itself to see if it is beveled correctly as per the instructions, the question is: Does the seating tool need to be rotated until the face of it is flush with the face of the port to which it slides into? I ask because I have applied pressure and turned and turned and turned (all the while cleaning the bit and reapplying lithium paste to the bit) and come to a place where it doesn’t seem to be meeting resistance and the rotator is about a quarter to one half inch away from the face of the port. Should I keep beveling until it is flush?

Last edited by Ando; 07-03-2021 at 03:23 PM.
Reply With Quote
  #24   IP: 47.142.131.74
Old 07-03-2021, 09:04 PM
JOHN COOKSON JOHN COOKSON is offline
Afourian MVP, Professor Emeritus
 
Join Date: Nov 2008
Posts: 3,500
Thanks: 54
Thanked 855 Times in 629 Posts
Quote:
Originally Posted by Ando View Post

In the meantime, since there’s probably no way for me to peer into the port itself to see if it is beveled correctly as per the instructions, the question is: Does the seating tool need to be rotated until the face of it is flush with the face of the port to which it slides into? I ask because I have applied pressure and turned and turned and turned (all the while cleaning the bit and reapplying lithium paste to the bit) and come to a place where it doesn’t seem to be meeting resistance and the rotator is about a quarter to one half inch away from the face of the port. Should I keep beveling until it is flush?
If you don't get an answer from a forum member R\E this, call Ken at MMI.

ex TRUE GRIT
Reply With Quote
The Following User Says Thank You to JOHN COOKSON For This Useful Post:
Ando (07-03-2021)
  #25   IP: 174.255.132.208
Old 07-03-2021, 09:36 PM
Ando's Avatar
Ando Ando is offline
Senior Member
 
Join Date: Jul 2019
Location: San Pedro, CA
Posts: 247
Thanks: 333
Thanked 58 Times in 38 Posts
The turning knob thrashed my hands so bad that I’m thinking to cut it off and put the remaining shaft (that the drill bit is attached to) to a power tool and making quick work of it. That is, if it is supposed to sit flush. Monday, Monday.

I just now drilled more and more by hand and reassembled and started and it started at ~20 went up to 35 with throttle and then dropped off again to close to zero when I eased it back to idle. Still haven’t got the oil pressure gauge…taking advantage of the sun bc it’s too beautiful a day today. I’ll get to it. Yes have faith in myself
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Increasing Oil Pressure dvd Troubleshooting 14 12-04-2013 01:38 PM
Oil Pressure Adjustment Jesse Delanoy General Maintenance 59 07-24-2010 09:14 PM
Information about information and oil pressure issues Don Moyer Announcements 0 04-14-2009 08:30 AM
Oil Pressure / Rear oil seal - Next step Mark Harrington Drive Train / Propellers 6 11-24-2008 08:51 AM
Carburetor Internal Pressure Regulation Don Moyer Fuel System 2 04-12-2005 09:30 AM


All times are GMT -4. The time now is 04:16 PM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2024 Moyer Marine Inc.

All Rights Reserved