Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Discussion Topics > Cooling System

Reply
 
Thread Tools Display Modes
  #1   IP: 73.93.238.186
Old 06-21-2021, 05:51 PM
ajgaines ajgaines is offline
Senior Member
 
Join Date: Aug 2019
Location: Alameda
Posts: 58
Thanks: 10
Thanked 0 Times in 0 Posts
Water in Oil

The previous owners of my Catalina 30 had backflowed the exhaust water into the cylinders and destroyed the A4 that way.

I bought a rebuilt A4 and installed it and finally have had the chance to use the boat a bunch the last couple of months. I found that I was having issues with my RPMs only going up to about 1300 and after I wasn't even able to fight a breeze to get out of my slip I decided it was finally a problem.

I found water in the oil once again. I have religiously closed the seacock when cranking and really don't know how the water got in there. Perhaps it is just because of the small amount of clearance from where the raw "used" water enters my hot section of the exhaust? With the Catalina 30 there's really no space to put it any higher.

Anyone have any suggestions?
One thing I was thinking was to install the closed fresh water system but the fresh water cooling system that moyer sells would not fit either as there is no clearance behind the flywheel for the 2" required.
I had also changed out the entire exhaust hose portion of the exhaust but it still has the old muffler. Is there something in the muffler itself that could be backing the water up?
Reply With Quote
  #2   IP: 155.186.122.195
Old 06-21-2021, 06:04 PM
Dave Neptune Dave Neptune is offline
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Grove, Oklahoma
Posts: 5,035
Thanks: 711
Thanked 1,289 Times in 839 Posts
The water can also get in through a pin hole in the manifold which luckily is an easy check and a not so cheap fix. An exhaust issue may require some tweaking of the system you have. I doubt your system is still stock and we have a few Cat 30 guru's on this site for excellent guidance.

Dave Neptune
Reply With Quote
  #3   IP: 155.186.122.195
Old 06-21-2021, 06:06 PM
Dave Neptune Dave Neptune is offline
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Grove, Oklahoma
Posts: 5,035
Thanks: 711
Thanked 1,289 Times in 839 Posts
Pt II

Did you check the anti-syphon valve in the cooling loop?

Dave Neptune
Reply With Quote
  #4   IP: 100.36.65.17
Old 06-21-2021, 10:25 PM
edwardc's Avatar
edwardc edwardc is offline
Afourian MVP
 
Join Date: Aug 2009
Location: Laurel, MD
Posts: 2,509
Thanks: 153
Thanked 595 Times in 388 Posts
A fresh water cooling system (FWC) will not help with an exhaust water reflux problem as the FWC system still uses raw water to cool the exhaust.

I know the Catalina's are severely height limited, but every little bit helps. The farther and lower the water injection point is, the better. On my original engine (not in a Catalina), the exhaust elbow had NO riser!! A simple 90 degree turn downwards, with the water injected right in the elbow! Spray and steam could (and did) migrate back into the manifold.

Ideally, you want the water injection point to be at least 4" lower than the bottom edge of the exhaust opening on the manifold, with as much lift (even an inch!) as possible between it and the manifold. And an anti-siphon valve in the water injection path is a must. Put it at the top of a hose loop, placed as high as you can inside the cabinetry.
__________________
@(^.^)@ Ed
1977 Pearson P-323 "Dolce Vita"
with rebuilt Atomic-4

Reply With Quote
The Following User Says Thank You to edwardc For This Useful Post:
ajgaines (06-22-2021)
  #5   IP: 104.174.83.118
Old 06-21-2021, 11:19 PM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
Catalina 30 guys beware

In addition to the latest Moyer Marine Newsletter, An Exhausting Problem, the Catalina 30 has some serious exhaust system design challenges, particularly the style of waterlift muffler combined with the low rise hot section. Using the Centek line of waterlifts as an example, a side inlet muffler (as opposed to a top inlet) introduces a significant backflooding risk while heeled. The attached drawing shows both types on an even keel and under 15° of heel, sloshing under way not included. The blue dashed line represents the typical residual water level inside the waterlift muffler after engine shutdown. As can be seen, the side inlet greatly reduces the usable, backflood preventing volume of the muffler.
Attached Images
 
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others

Last edited by ndutton; 06-21-2021 at 11:25 PM. Reason: Resized drawing
Reply With Quote
  #6   IP: 172.58.91.78
Old 06-22-2021, 02:07 AM
ajgaines ajgaines is offline
Senior Member
 
Join Date: Aug 2019
Location: Alameda
Posts: 58
Thanks: 10
Thanked 0 Times in 0 Posts
Quote:
Originally Posted by Dave Neptune View Post
Did you check the anti-syphon valve in the cooling loop?

Dave Neptune
I know it has one. How do I check that it is working?
Reply With Quote
  #7   IP: 172.58.91.78
Old 06-22-2021, 02:09 AM
ajgaines ajgaines is offline
Senior Member
 
Join Date: Aug 2019
Location: Alameda
Posts: 58
Thanks: 10
Thanked 0 Times in 0 Posts
Quote:
Originally Posted by edwardc View Post
A fresh water cooling system (FWC) will not help with an exhaust water reflux problem as the FWC system still uses raw water to cool the exhaust.

I know the Catalina's are severely height limited, but every little bit helps. The farther and lower the water injection point is, the better. On my original engine (not in a Catalina), the exhaust elbow had NO riser!! A simple 90 degree turn downwards, with the water injected right in the elbow! Spray and steam could (and did) migrate back into the manifold.

Ideally, you want the water injection point to be at least 4" lower than the bottom edge of the exhaust opening on the manifold, with as much lift (even an inch!) as possible between it and the manifold. And an anti-siphon valve in the water injection path is a must. Put it at the top of a hose loop, placed as high as you can inside the cabinetry.
It allows about 1.5" under the cabinet. I guess it would be possible to try to figure out a way to build a higher hot exhaust up into the cabinet and take out the bottom drawer, but maybe that would risk fire? I haven't seen anyone else that's done that
Reply With Quote
  #8   IP: 172.58.91.78
Old 06-22-2021, 02:12 AM
ajgaines ajgaines is offline
Senior Member
 
Join Date: Aug 2019
Location: Alameda
Posts: 58
Thanks: 10
Thanked 0 Times in 0 Posts
Quote:
Originally Posted by ndutton View Post
In addition to the latest Moyer Marine Newsletter, An Exhausting Problem, the Catalina 30 has some serious exhaust system design challenges, particularly the style of waterlift muffler combined with the low rise hot section. Using the Centek line of waterlifts as an example, a side inlet muffler (as opposed to a top inlet) introduces a significant backflooding risk while heeled. The attached drawing shows both types on an even keel and under 15° of heel, sloshing under way not included. The blue dashed line represents the typical residual water level inside the waterlift muffler after engine shutdown. As can be seen, the side inlet greatly reduces the usable, backflood preventing volume of the muffler.
I see. Mine has the fiberglass muffler with the in and out both on the top. I had to refiner glass it a little but it seems to be as big as the mufflers get for retaining water
Reply With Quote
  #9   IP: 104.174.83.118
Old 06-22-2021, 09:04 AM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
Top in - top out is the point I was trying to drive home for the Catalina 30 and other boats with engines similarly situated. Can you provide pictures of your hot section and water injection? Maybe we'll see something. Pictures of mine (also a C30) are attached.

Does your exhaust hose have a check valve inside the port cockpit sail locker? You mentioned your anti-siphon has a valve. You might consider a vented loop instead.
Attached Images
  
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others
Reply With Quote
  #10   IP: 155.186.122.195
Old 06-22-2021, 10:54 AM
Dave Neptune Dave Neptune is offline
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Grove, Oklahoma
Posts: 5,035
Thanks: 711
Thanked 1,289 Times in 839 Posts
I had an E35MKII which has the same style installation. I cut a couple of holes in a shelf that ran under the toe rail inside. Although it was on the port side it was as high as I could get it and not have it outside somewhere. Raising the anti syphon really helped for my installation. Getting it as high and close to centerline is best. I had no problems on starboard tach when it was at it's "lowest" however I did not have it in any extreme weather keeping her really heeled over.

Checking the valve is quite simple. Once the valve and loop are removed the integrity can be checked by simply plugging one end and sucking and blowing on the other. It should hold when you blow and release when you suck on it, not rocket science . It is nothing but a check valve and personally I replaced mine every 4~5 years rather than cleaning because I had so little "rise" available above the engine since we too sat on it inside the boat.

Neil will probably have a good idea of where to mount the valve on your Cat 30 as he has a really nice one, and I do mean really nice!

Dave Neptune
Reply With Quote
  #11   IP: 172.58.38.148
Old 06-22-2021, 04:49 PM
ajgaines ajgaines is offline
Senior Member
 
Join Date: Aug 2019
Location: Alameda
Posts: 58
Thanks: 10
Thanked 0 Times in 0 Posts
Quote:
Originally Posted by ndutton View Post
Top in - top out is the point I was trying to drive home for the Catalina 30 and other boats with engines similarly situated. Can you provide pictures of your hot section and water injection? Maybe we'll see something. Pictures of mine (also a C30) are attached.

Does your exhaust hose have a check valve inside the port cockpit sail locker? You mentioned your anti-siphon has a valve. You might consider a vented loop instead.
Name:  IMG_20210622_134322.jpg
Views: 329
Size:  91.0 KB
Name:  IMG_20210622_134234.jpg
Views: 346
Size:  45.3 KB

This is the setup. Looks similar to yours. I couldn't get more clearance without going up out of the engine area, and I'm not sure how I would do that.

What did you use to seal your hot exhaust portion? I would smell a lot of exhaust when running the engine and I believe it was leaking somewhere out of there. I found it hard to set it up quickly so I had to unscrew a few times while screwing it all together
Reply With Quote
  #12   IP: 104.174.83.118
Old 06-22-2021, 08:27 PM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
Quote:
Originally Posted by ajgaines View Post
What did you use to seal your hot exhaust portion?
This is the sealant I used, available at McMaster-Carr. It's rated to 750°
Attached Images
  
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others
Reply With Quote
  #13   IP: 199.87.176.85
Old 06-23-2021, 09:23 AM
zellerj zellerj is offline
Afourian MVP
 
Join Date: May 2005
Posts: 304
Thanks: 5
Thanked 115 Times in 69 Posts
Water can also get into the engine via the exhaust when large waves hit the stern pushing water back through the exhaust. This happened to me when I was stuck on a sand bar and boat wake slapped the stern on my CAT30. If your slip exposes your stern to wakes or chop this could be the issue. Many exhaust systems have an exhaust flapper on the stern, but they are prone to falling off.

Check to see if your exhaust hose is high in the port lazerette. It should have the high spot close to the bottom of the port cockpit seat.
__________________
Jim Zeller
1982 Catalina 30
Kelleys Island, Ohio

Last edited by zellerj; 06-23-2021 at 09:28 AM.
Reply With Quote
  #14   IP: 172.58.159.87
Old 07-03-2021, 04:10 PM
ajgaines ajgaines is offline
Senior Member
 
Join Date: Aug 2019
Location: Alameda
Posts: 58
Thanks: 10
Thanked 0 Times in 0 Posts
It seems the antisiphon valve isn't working but how would that flood the muffler?
Reply With Quote
  #15   IP: 47.142.131.74
Old 07-03-2021, 09:00 PM
JOHN COOKSON JOHN COOKSON is offline
Afourian MVP, Professor Emeritus
 
Join Date: Nov 2008
Posts: 3,500
Thanks: 54
Thanked 855 Times in 629 Posts
Quote:
Originally Posted by ajgaines View Post
It seems the antisiphon valve isn't working but how would that flood the muffler?
It's the other way. Water in the muffler gets siphoned into the engine. The antisiphon valve breaks the siphon.
As a warm engine cools it can, in some cases, create enough of a vacuum to start a siphon from the exhaust system into the engine.

ex TRUE GRIT
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Winterizing A4 and General Boat Preparation Mo General Maintenance 85 11-05-2021 06:26 AM
atomic 4 - 6 months of salt water - lost cause? taylor Overhaul 35 01-30-2021 10:32 PM
Head Removal rabbit hole Hiker_00 Overhaul 49 12-04-2012 11:33 PM
acid flush of Fresh water cooled engine skhorleb Cooling System 1 01-16-2007 10:07 AM
Much much water in Atomic 4 seators Cooling System 3 08-10-2006 03:31 PM


All times are GMT -4. The time now is 07:14 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2024 Moyer Marine Inc.

All Rights Reserved