Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Discussion Topics > Fuel System

Reply
 
Thread Tools Display Modes
  #1   IP: 161.216.164.202
Old 08-11-2022, 05:26 PM
julienrobi3 julienrobi3 is offline
Senior Member
 
Join Date: Feb 2021
Posts: 13
Thanks: 16
Thanked 2 Times in 2 Posts
Unable to unscrew screw for oil pressure safety switch

Hello! I've just switched from a mechanical fuel pump to an electrical one (works like a charm). However, I want to install a oil pressure safety switch where it is recommended to do so (where the arrow points on the picture: https://www.moyermarineforum.com/for...1&d=1660252652 ).

The problem is that this screw is completely jammed! I've tried adding wd-40, but it won't turn one bit. So l, I thought I had two options: drill the screw or install the switch somewhere else.
Since I really don't want to take the chance of damaging the hole's thread, Im looking for another place to install it. Is this possible at all?
Thanks a lot for your inputs!
Julien
Attached Images
 
Reply With Quote
The Following User Says Thank You to julienrobi3 For This Useful Post:
TimBSmith (08-11-2022)
  #2   IP: 32.211.38.220
Old 08-11-2022, 06:15 PM
Al Schober's Avatar
Al Schober Al Schober is offline
Afourian MVP
 
Join Date: Jul 2009
Location: Uncasville, CT
Posts: 2,002
Thanks: 16
Thanked 578 Times in 405 Posts
I ended up with an oil pressure sender, a mechanical gauge, and the OPSS all mounted on a manifold off engine. The manifold was connected to the fwd port (where the oil pressure sender usually mounts) by an 18" length of grease gun hose (from Home Depot).
Those slotted brass plugs are always a problem. Whenever I went through an engine I replaced them all with plugs with a hex socket. More better!
Reply With Quote
The Following 3 Users Say Thank You to Al Schober For This Useful Post:
julienrobi3 (08-17-2022), TimBSmith (08-11-2022), W2ET (08-11-2022)
  #3   IP: 104.174.83.118
Old 08-12-2022, 12:30 PM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
My array of oil pressure sensors (OPSS, gauge sender and EWDS switch) are installed the same as Al's, remotely on a bulkhead and connected to the same port behind the flywheel with a pressure rated hose. For the gauge sender and EWDS switch to work the array must have a ground wire connected.

As for the stuck plug, an impact driver will make quick work of it.
Attached Images
 
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others
Reply With Quote
The Following 2 Users Say Thank You to ndutton For This Useful Post:
julienrobi3 (08-17-2022), TimBSmith (08-12-2022)
  #4   IP: 64.246.99.67
Old 08-14-2022, 08:52 PM
zellerj zellerj is offline
Afourian MVP
 
Join Date: May 2005
Posts: 304
Thanks: 5
Thanked 115 Times in 69 Posts
I have had good luck with an impact screwdriver, one that you hit with a hammer and it turns the screwdriver at the same time.

https://www.amazon.com/TEKTON-2910-2...24752796&psc=1
__________________
Jim Zeller
1982 Catalina 30
Kelleys Island, Ohio
Reply With Quote
The Following 2 Users Say Thank You to zellerj For This Useful Post:
julienrobi3 (08-17-2022), TimBSmith (08-15-2022)
  #5   IP: 66.131.247.127
Old 08-17-2022, 08:50 AM
julienrobi3 julienrobi3 is offline
Senior Member
 
Join Date: Feb 2021
Posts: 13
Thanks: 16
Thanked 2 Times in 2 Posts
Tbanks everyone for your answers. I followed your advices and installed it where the oil sender is. And eventually I will try using an impact screwdriver to remove the screw if I have an issue with where the switch is now.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Oil Pressure Safety Switch questions??? southcoasting Troubleshooting 29 05-26-2023 02:48 PM
oil pressure safety switch morgan_out_island Fuel System 5 05-25-2023 10:53 AM
oil pressure safety switch JimHo Troubleshooting 7 09-21-2016 11:02 AM
oil pressure safety switch ramon Safety 7 05-18-2010 10:34 AM
wiring question- oil pressure safety switch? msmith10 Electrical 2 09-10-2006 08:03 AM


All times are GMT -4. The time now is 09:57 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2024 Moyer Marine Inc.

All Rights Reserved