Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Discussion Topics > Troubleshooting

Reply
 
Thread Tools Display Modes
  #1   IP: 66.131.242.231
Old 03-14-2021, 02:04 PM
julienrobi3 julienrobi3 is offline
Senior Member
 
Join Date: Feb 2021
Posts: 13
Thanks: 16
Thanked 2 Times in 2 Posts
Reverse gear seems to work, but actually doesn't!

Hello,
I have an atomic 4 on my C&C 30. I have been sailing it for one year.
The motor works perfectly when it goes forward. The issue is when I need to go backward. It doesnt do anything, or almost anything. When there is no wind and no current, I can move really slowly, less than 1knot. So it doesnt take a lot to lose complete control of the boat!
By reading the manual, I thought that it might have been the reverse gear that needed some adjustment. But it didnt seem to be the problem. The shaft was turning quite fast in reverse, and accelerating when increasing RPM.
So I thought there was a problem with my propeller. When I got it out of the water for the winter, I did some tests and the propeller seemed to turn normally.
So the only thing that I think might be the issue is the type of propeller I have. I know the engine was replaced by an atomic 4 in the past, so could it be that I dot have the right propeller for the type of engine?
Here is the image of my propeller. It is about about 20 cm (8 inches) in diameter.

https://ibb.co/HpBy0Vm (link to image)


This is my first boat, and I even more newbie in the field of mechanics, so I might have missed important things to check in order to find the real problem. So if you have any idea of what could be the issue, I would be really happy to hear your advice!

Thanks a lot !
Reply With Quote
  #2   IP: 134.41.100.227
Old 03-14-2021, 02:10 PM
Mo's Avatar
Mo Mo is offline
Afourian MVP
 
Join Date: Jun 2007
Location: Halifax NS,
Posts: 4,470
Thanks: 292
Thanked 411 Times in 272 Posts
I have a 12 / 9 on my C&C 30 and it does everything well. It's an old design michigan prop. A 12 /7 would also be a decent prop for that boat. If you were looking around for either I double check the size of the shaft (usually 7/8 inch) unless someone changed it. Check on-line, ebay etc. If buying a new prop buy a 12 inch. The other option is 2 blade props but they don't reverse as well.

With that small prop diameter you have I'd think you'd be doing some higher rpms in forward gear as well and sucking a bit more fuel than you need to be.
__________________
Mo

"Odyssey"
1976 C&C 30 MKI

The pessimist complains about the wind.
The optimist expects it to change.
The realist adjusts the sails.
...Sir William Arthur Ward.

Last edited by Mo; 03-14-2021 at 02:13 PM.
Reply With Quote
The Following User Says Thank You to Mo For This Useful Post:
julienrobi3 (03-15-2021)
  #3   IP: 104.174.83.118
Old 03-14-2021, 02:19 PM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
The prop appears to be an Indigo, designed, manufactured and sold by a member of this forum by the same name. I suggest you contact him for the best analysis of your symptom.

Another thought:
Is the engine a direct drive or reduction gear?
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others
Reply With Quote
The Following User Says Thank You to ndutton For This Useful Post:
julienrobi3 (03-15-2021)
  #4   IP: 67.169.215.221
Old 03-14-2021, 04:09 PM
ronstory's Avatar
ronstory ronstory is offline
Afourian MVP
 
Join Date: Feb 2016
Posts: 404
Thanks: 106
Thanked 208 Times in 152 Posts
Are you sure the prop is only 8" in diameter? The indigo prop is 10" and I agree with Neil it does look like Tom's prop... but the size would be wrong

Just do a google search for Indigo Electronics.

... and welcome to the forum.
__________________
Thanks,
Ron
Portland, OR
Reply With Quote
The Following User Says Thank You to ronstory For This Useful Post:
julienrobi3 (03-15-2021)
  #5   IP: 108.79.1.46
Old 03-14-2021, 05:16 PM
jbsoukup's Avatar
jbsoukup jbsoukup is offline
Afourian MVP
 
Join Date: Jan 2012
Location: chicago
Posts: 148
Thanks: 0
Thanked 12 Times in 9 Posts
there's no detent in reverse so if you're giving it a lot of throttle you might have to ride the reverse lever (put pressure on it). it makes a distinct sound when engaged and reversing.
__________________
john
'77 catalina 30 #783
the only way to be sure is to make sure
Reply With Quote
The Following 2 Users Say Thank You to jbsoukup For This Useful Post:
julienrobi3 (03-15-2021), Sam (03-15-2021)
  #6   IP: 68.134.226.200
Old 03-14-2021, 05:29 PM
joe_db's Avatar
joe_db joe_db is offline
Afourian MVP
 
Join Date: May 2009
Posts: 4,474
Thanks: 49
Thanked 1,026 Times in 721 Posts
That is an Indigo 10" prop. You are not going all the way into reverse.
Reply With Quote
The Following User Says Thank You to joe_db For This Useful Post:
julienrobi3 (03-15-2021)
  #7   IP: 134.41.100.227
Old 03-14-2021, 06:23 PM
Mo's Avatar
Mo Mo is offline
Afourian MVP
 
Join Date: Jun 2007
Location: Halifax NS,
Posts: 4,470
Thanks: 292
Thanked 411 Times in 272 Posts
Quote:
Originally Posted by jbsoukup View Post
there's no detent in reverse so if you're giving it a lot of throttle you might have to ride the reverse lever (put pressure on it). it makes a distinct sound when engaged and reversing.
Agree completely, a video with audio of the boat going into reverse would certainly help.
__________________
Mo

"Odyssey"
1976 C&C 30 MKI

The pessimist complains about the wind.
The optimist expects it to change.
The realist adjusts the sails.
...Sir William Arthur Ward.

Last edited by Mo; 03-14-2021 at 06:26 PM.
Reply With Quote
The Following User Says Thank You to Mo For This Useful Post:
julienrobi3 (03-15-2021)
  #8   IP: 155.186.122.195
Old 03-14-2021, 06:24 PM
Dave Neptune Dave Neptune is offline
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Grove, Oklahoma
Posts: 5,035
Thanks: 711
Thanked 1,289 Times in 839 Posts
To engage reverse you need to hold the clutches in place manually, if you are just moving the handle back and not holding it it will slip.

That's an Indigo prop for sure. I ran one for many many years on my old E-35MKII that I have since sold.

Dave Neptune
Reply With Quote
The Following User Says Thank You to Dave Neptune For This Useful Post:
julienrobi3 (03-15-2021)
  #9   IP: 134.41.100.227
Old 03-14-2021, 06:25 PM
Mo's Avatar
Mo Mo is offline
Afourian MVP
 
Join Date: Jun 2007
Location: Halifax NS,
Posts: 4,470
Thanks: 292
Thanked 411 Times in 272 Posts
C&C 30 is direct drive normally. It wouldn't have a reduction gear unless the engine and step were moved forward with considerable modification to the step in the galley area.
__________________
Mo

"Odyssey"
1976 C&C 30 MKI

The pessimist complains about the wind.
The optimist expects it to change.
The realist adjusts the sails.
...Sir William Arthur Ward.
Reply With Quote
The Following User Says Thank You to Mo For This Useful Post:
julienrobi3 (03-15-2021)
  #10   IP: 47.142.136.120
Old 03-14-2021, 08:00 PM
JOHN COOKSON JOHN COOKSON is offline
Afourian MVP, Professor Emeritus
 
Join Date: Nov 2008
Posts: 3,500
Thanks: 54
Thanked 855 Times in 629 Posts
LINKAGE PROLEM?

The first thing I would do is disconnect the shift cable and shift by hand on the trany lever. Check the outer cable cover. It needs to be held down firmly and not move.

ex TRUE GRIT
Reply With Quote
The Following 2 Users Say Thank You to JOHN COOKSON For This Useful Post:
julienrobi3 (03-15-2021), Sam (03-15-2021)
  #11   IP: 66.131.242.231
Old 03-15-2021, 08:18 AM
julienrobi3 julienrobi3 is offline
Senior Member
 
Join Date: Feb 2021
Posts: 13
Thanks: 16
Thanked 2 Times in 2 Posts
Thank for all the replies. The diameter is probably my mistake and it would make sense that it is a 10". I live in Canada and my sailboat is currently not easily reachable (cold and snow), so I cannot verify the information just yet.

So if I am not mistaken, I understand from all your answers that my propeller might not be perfect for my engine, yet it might not be the main issue (but I will definitely get in touch with the Indigo guy).

Once the snow melts I will do some more checking according to your replies, and will post a video if I still have issues!

Thanks again everyone. This Afourians community seems really friendly and helpful !
Reply With Quote
  #12   IP: 138.207.177.95
Old 03-15-2021, 09:06 AM
joe_db's Avatar
joe_db joe_db is offline
Afourian MVP
 
Join Date: May 2009
Posts: 4,474
Thanks: 49
Thanked 1,026 Times in 721 Posts
The Indigo prop is perfect for the engine more or less, it is specifically designed for A4s pushing displacement hulls.
The A4 uses a reduction gear in reverse, but not in forward. There are several things that can go wrong:
1. Lever not moving forward enough to get into forward detent.
2. Lever not moving back enough to fully engage reverse.
3. Internal adjustment issues.
1 and 2 can be fixed with cable adjustments usually.
Reply With Quote
The Following 4 Users Say Thank You to joe_db For This Useful Post:
Dave Neptune (03-15-2021), julienrobi3 (04-13-2021), ronstory (03-15-2021), Sam (03-15-2021)
  #13   IP: 165.225.20.178
Old 03-16-2021, 06:23 AM
Surcouf's Avatar
Surcouf Surcouf is offline
Afourian MVP, Professor Emeritus
 
Join Date: May 2018
Posts: 361
Thanks: 328
Thanked 163 Times in 123 Posts
I would add that the understanding if your shaft is spinning as it should, or if your gear is "slipping" when in reverse, is key here. You mentioned earlier that it seems to accelerate when you ramp up the rpm.
- Can you confirm that you keep the same ration "rpm engine" / "rpm shaft" when you hold the shift handle at "idle rpm", and at "higher rpm"? This could be checked with a cheap Harbor F**** speed gun ( I did that to tune the idle speed on mine), depending on the accessibility in your boat of course
- if it is slipping, all the items mentioned by the others on shift cable / gear adjustment apply.
- if it is not slipping, you are back to you prop... first question: how clean is it? after comes the choice of the prop, and I am useless on that
__________________
Surcouf
A nostalgic PO - Previously "Almost There" - Catalina 27 (1979)
Reply With Quote
The Following User Says Thank You to Surcouf For This Useful Post:
julienrobi3 (04-13-2021)
  #14   IP: 138.207.177.95
Old 03-16-2021, 10:01 AM
joe_db's Avatar
joe_db joe_db is offline
Afourian MVP
 
Join Date: May 2009
Posts: 4,474
Thanks: 49
Thanked 1,026 Times in 721 Posts
The Indigo prop has one weak spot - barnacles. In order to not be a huge drag under sail it does not have a lot of blade area. It only takes a few barnacles to really screw it up.
Reply With Quote
The Following 2 Users Say Thank You to joe_db For This Useful Post:
julienrobi3 (04-13-2021), sastanley (03-17-2021)
  #15   IP: 66.131.242.231
Old 05-03-2021, 12:48 PM
julienrobi3 julienrobi3 is offline
Senior Member
 
Join Date: Feb 2021
Posts: 13
Thanks: 16
Thanked 2 Times in 2 Posts
Hello everyone!
So I got to do some tests in order to investigate further my motor problem, and additionnal help from you guys would be really helpful!

So I basically did two things:
1. Test the shaft RPM with a speed gun as mentionned by Surcouf.
2. Look inside the gear box for anything weird.

1. RPM tests
I have tested the RPM at forward and reverse to see if there was some differences. And since the boat is out of the water (so less friction on the prop?) and that I have used a speed gun that I dont really know if it is well calibrated, I dont think we can use the actually absolute numbers, but we can still compare the numbers between them (that is my assumptions, I might totally be wrong about this).
So at mid power and forward, the shaft is at 3000 RPM.
At mid power and reverse, it drops to 900 RPM.
From what I've read, t is normal that the reverse RPM is lower than forward.
But the weird thing occurs when I try to add a more throttle when in reverse.
At some point, the shaft RPM drops almost completely and seems to be at neutral!

2. Opening the gear box
From the previous experiment, I suspected that there was something wrong within the transmission.
So I opened it and played a little bit with the lever to change from forward to neutral to reverse.
I've taken a small video of this:

https://photos.app.goo.gl/KgCshZdJKLfEP6Pr5

Since it is a bit fast, you can pause at different moments to see the positions:
Pause at 3 seconds to see the forward position.
Pause at 6 seconds to see the neutral position.
Pause at 15 seconds to see the reverse position (at that position, I cannot go further with the lever).

So as you can see, there is very little difference between the neutral and reverse position. From other videos of other people, I have seen that the plate fingers could go a lot further than mine.
And actually, the first thing I noticed when I started to play with the lever was that everything seemd to wobble when going from neutral to reverse, even the gear case. And I thought to myself that it probably wasnt normal.

So maybe some elements of the gear are getting loose? and I guess it would make sense that the reverse cannot be engaged properly if everything moves with the lever....
So what do you guys think?
Is there some bolts I should firsst thighten to prevent what is not supposed to move from moving?

Again, thank you very much for your help, this is really appreciated!

Julien
Reply With Quote
  #16   IP: 68.10.71.200
Old 05-03-2021, 01:02 PM
indigo indigo is offline
 
Join Date: Jun 2007
Location: Williamsburg, VA
Posts: 54
Thanks: 8
Thanked 54 Times in 28 Posts
Indigo Prop for Sure

That is indeed an indigo prop, no question about it. And it is 10” in diameter.

You should try taking the shift linkage loose from the engine and see if the lever on the engine will go farther in the reverse direction with things disconnected. It may be a simple matter of getting your cable and linkage adjusted properly.

You also need to give the engine lots of RPM in reverse as there is a 1.3:1 speed reduction in reverse.

Tom
Reply With Quote
Old 05-03-2021, 01:10 PM
JOHN COOKSON
This message has been deleted by JOHN COOKSON.
  #17   IP: 66.131.242.231
Old 05-03-2021, 01:10 PM
julienrobi3 julienrobi3 is offline
Senior Member
 
Join Date: Feb 2021
Posts: 13
Thanks: 16
Thanked 2 Times in 2 Posts
Hello Tom,
Thank you for your reply.
I have already did what you said. Please feel free to read the update I posted today at 12:48 PM. Thank you
Reply With Quote
  #18   IP: 68.10.71.200
Old 05-03-2021, 01:59 PM
indigo indigo is offline
 
Join Date: Jun 2007
Location: Williamsburg, VA
Posts: 54
Thanks: 8
Thanked 54 Times in 28 Posts
Sorry that I mis-interpreted your video. I saw linkage still attached to the engine shift lever and assumed everything was still hooked up. Upon further inspection of the video, I see a bracket of some sort flopping around as you shift so I assume you made the disconnect at the cockpit shift lever. My bad!

Tom
Reply With Quote
  #19   IP: 165.225.20.156
Old 05-03-2021, 03:25 PM
Surcouf's Avatar
Surcouf Surcouf is offline
Afourian MVP, Professor Emeritus
 
Join Date: May 2018
Posts: 361
Thanks: 328
Thanked 163 Times in 123 Posts
Quote:
Originally Posted by julienrobi3 View Post
Hello everyone!
So I got to do some tests in order to investigate further my motor problem, and additionnal help from you guys would be really helpful!

So I basically did two things:
1. Test the shaft RPM with a speed gun as mentionned by Surcouf.
2. Look inside the gear box for anything weird.
I am really not an expert on transmission but:
- it seems that your "fingers" correctly "climb" on the collar where they are supposed to go when you are in "forward" (the "forward latch" ). When you put your transmission lever on "forward", these fingers have to "climb" and stay there without you needing to hold the lever forward. My english s*** so go listen to the Boss on you tube. He is very very clearly how this system works
https://www.youtube.com/watch?v=B7Qc0HZ2juA

And just to make sure, as already noted: you need to manually hold the handle / lever n the cokpit full reverse so that the shaft turns backward. If you put it back and release it, it will come back to neutral by itself (could that explain the 0 RPM?)

good luck
__________________
Surcouf
A nostalgic PO - Previously "Almost There" - Catalina 27 (1979)
Reply With Quote
  #20   IP: 69.250.111.245
Old 05-03-2021, 09:45 PM
sastanley's Avatar
sastanley sastanley is offline
Afourian MVP
 
Join Date: Sep 2008
Location: Solomons, MD
Posts: 7,016
Thanks: 1,134
Thanked 600 Times in 442 Posts
Julien...you are pushing against the spring in the front of the case when going into reverse...this is why you need to 'lean' on the lever to keep it in reverse. As your video showed, the little fingers lock all the clutches in FWD with the 'detent'. But in reverse, there is no positive engagement, you must keep pressure on the shift lever to keep the parts engaged...and it should literally scream at you, and as Tom noted, with a reduction, you need more RPM in reverse for the same prop speed as compared to FWD. I cruise about 1,900-2,000 RPM in FWD with my Indigo prop, but in reverse, she's spinning 2,500 RPM..be careful..once you figure it out, the next thing you gotta do is hold the tiller/wheel because it will fly out of your hands while you are busy with the shift lever. I have a tiller, so I usually sit and hold the tiller with one hand, or straddle it facing backwards, and then sit in the cockpit so I can control the engine with the other hand, to keep a little pressure on the shift lever..when it starts to slip the RPMs will really go and the 'screaming' will studdenly stop..similar to a clutch in a car. If I remember how it works, the mechanicals make the sun/planetary gears inside there change direction, which makes the prop shaft reverse, hence the 'screaming' sound..Also, the drive gear system shares the engine oil for lube..

One last warning..until I saw your video, your post sounded like you'd run the engine on the hard - The rubber cutlass bearing needs seawater lubrication, so be sure not to run it on the hard, unless you can feed the engine cooling water, AND the cutlass bearing inside the prop strut with water. It did not look to me like anything was out of normal ops in there, so I think it is probably just a little education and practice once you are back in the water to figure it out.

Good luck. I like my Indigo prop...the idea of the smaller diameter allows the engine RPMs to be higher and not lug the motor so much. The redline is like 3,500 RPM, so at 1,700 with a big prop she is working hard...the Indigo helps with this. Agree with Joe_db..due to small size, the only downside is any growth degrades performance..that just means I have to clean/dive the prop/bottom more often or short haul in the middle of the season..which makes the boat happier anyway.

I just hauled today. I did not get a good picture pre-scrape/power wash, but I was still able to motor to the travel lift, but there was noticeable degradation in performance..still totally maneuverable and I even backed all the way down the fairway to the travel lift at about 1,900 RPM in reverse, against the wind.
Attached Images
 
__________________
-Shawn
"Holiday" - '89 Alura 35 #109
"Twice Around" - '77 C-30, #511 with original A-4 & MMI manifold - SOLD! (no longer a two boat owner!!)
http://www.moyermarine.com/forums/signaturepics/sigpic3231_6.gif

Last edited by sastanley; 05-03-2021 at 10:06 PM.
Reply With Quote
The Following 2 Users Say Thank You to sastanley For This Useful Post:
Sam (05-06-2021), TimBSmith (05-04-2021)
  #21   IP: 134.41.87.78
Old 05-05-2021, 06:10 PM
Mo's Avatar
Mo Mo is offline
Afourian MVP
 
Join Date: Jun 2007
Location: Halifax NS,
Posts: 4,470
Thanks: 292
Thanked 411 Times in 272 Posts
I don't see the lock ring on the reverse adjustment nut...without it adjustment may move. Thoughts guys?
__________________
Mo

"Odyssey"
1976 C&C 30 MKI

The pessimist complains about the wind.
The optimist expects it to change.
The realist adjusts the sails.
...Sir William Arthur Ward.
Reply With Quote
  #22   IP: 104.174.83.118
Old 05-05-2021, 10:52 PM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
Quote:
Originally Posted by Mo View Post
I don't see the lock ring on the reverse adjustment nut...without it adjustment may move. Thoughts guys?
I see it, not easily but it's there, the original design spring clip.
Attached Images
 
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others

Last edited by ndutton; 05-05-2021 at 10:55 PM.
Reply With Quote
The Following User Says Thank You to ndutton For This Useful Post:
Mo (05-06-2021)
Reply

Tags
propeller, reverse, reverse gear, troubleshooting

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
reverse gear adjustments gilbert landin Reversing Gear 12 10-17-2013 08:31 PM
Forward and Reverse Gear Adjustment Issues CraigRun Reversing Gear 12 05-17-2012 09:15 PM
Reverse gear overheat?? NorfolkRagbagger Reversing Gear 5 10-13-2010 09:20 AM
early model reverse gear removal sun Reversing Gear 2 07-12-2009 06:18 PM


All times are GMT -4. The time now is 09:59 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2024 Moyer Marine Inc.

All Rights Reserved