#26
IP: 69.250.111.245
|
||||
|
||||
Oaktown...also, several of us have removed the hard copper line and gone to soft..that allows you to put polishing filters almost anywhere you want. I have one in between the mech pump and the carb, along with a fuel pressure gauge so I can be sure the pump is supplying fuel. Sorry, I don't have a good pic of that available.
__________________
-Shawn "Holiday" - '89 Alura 35 #109 "Twice Around" - '77 C-30, #511 with original A-4 & MMI manifold - SOLD! (no longer a two boat owner!!) |
The Following 2 Users Say Thank You to sastanley For This Useful Post: | ||
Dave Neptune (02-27-2023), W2ET (03-01-2023) |
#27
IP: 142.116.40.164
|
||||
|
||||
Hope this linking works.. pic of the hose, gauge and filter
https://www.moyermarineforum.com/for...1&postcount=85
__________________
Greg 1975 Alberg 30 |
#28
IP: 69.250.111.245
|
||||
|
||||
Thatch mod!
FWC'd Thatch'd motor with no bypass! (and you can just see the sideways chrome fuel pressure gauge near the carb, so it is sorta on topic!) This picture is amazingly 7 or 8 years old. I have since bumped up to the next size HX, and re-installed the t-stat. When this pic was taken (no t-stat under the housing), that little HX could barely keep up and I was running 180-190°F all the time. If anything went wrong I had no margin. I found a larger similar style SenDure HX at the salvage place in Stevensville, MD a few years ago. It is the same height, larger diameter, and probably double the cooling capacity, The reinstalled t-stat happily cycles all day long @155-165°F.
__________________
-Shawn "Holiday" - '89 Alura 35 #109 "Twice Around" - '77 C-30, #511 with original A-4 & MMI manifold - SOLD! (no longer a two boat owner!!) Last edited by sastanley; 03-01-2023 at 06:58 PM. |
#29
IP: 174.206.42.159
|
|||
|
|||
T-Stat Gasket
I'm about to install a new thermostat and gasket. There wasn't a gasket in place when the old one was removed (liquid gasket material was used.) Is the gasket installed above or beneath the thermostat? Thanks.
|
#30
IP: 76.176.224.167
|
||||
|
||||
Beneath. There's a recess in the upper thermostat housing for the thermostat flange to locate it properly.
__________________
Neil 1977 Catalina 30 San Pedro, California prior boats 1987 Westsail 32, 1970 Catalina 22 Had my hands in a few others |
The Following User Says Thank You to ndutton For This Useful Post: | ||
mhinnc (03-23-2023) |
Tags |
cooling system, power loss, thermostat, troubleshooting |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Modify Dole thermostat | Kelly | Cooling System | 11 | 06-01-2012 12:24 PM |
Thermostat installation instructions ( with spacer kit and original housing ) | seapadrik | Cooling System | 11 | 07-06-2011 02:35 PM |
Thermostat Housing Roof Too Low??? | Dana Paterson | Cooling System | 0 | 09-27-2007 10:32 PM |
New Products From Moyer Marine | Don Moyer | Cooling System | 0 | 10-05-2005 02:03 PM |
No Thermostat Action | mike7a10 | Cooling System | 0 | 09-06-2005 06:38 PM |