Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Discussion Topics > Drive Train / Propellers

Reply
 
Thread Tools Display Modes
  #1   IP: 72.220.199.69
Old 09-21-2022, 07:24 PM
Boatjoc Boatjoc is offline
Member
 
Join Date: Jun 2022
Posts: 2
Thanks: 0
Thanked 0 Times in 0 Posts
Rear Seal Replacement Questions

Name:  Rear Seal Issue.jpg
Views: 52
Size:  102.3 KB

I discovered during my last outing that I have the very issue with my rear seal that Don describes in his very helpful video, Rear Oil Seal Replacement. When I returned to my slip I looked in the engine compartment and saw that it was decorated with a ring of motor oil in a perfect 360 degree patern. So I am now faced with replacing the seal and perhaps even the coupling.

I have two important questions regarding this work. First, do I need to drain the oil, or is it at a level that it will spill out when the flange is removed? Second, in order the remove the flange that holds the seal I will need to move the prop shaft aft to create a space to pull it out of the engine compartment. Can this be done in the water or will a haul-out be required?

Any help regarding this unfortunate situation will be appreciated.
Reply With Quote
  #2   IP: 162.245.50.171
Old 09-21-2022, 07:59 PM
Dave Neptune Dave Neptune is offline
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Grove, Oklahoma
Posts: 4,718
Thanks: 626
Thanked 957 Times in 646 Posts
First welcome to the MMI forum.

Yes to draining the oil.

Yes it can be done in the water by being prepared and getting everything loose when ready to slide the shaft.

Once you have cleaned the shaft with a soft wire brush you can ease the packing and yes it will leak. Then the shaft will easily slide back. If you can get the shaft free of the coupling attach a hose clamp tightly to the end of the shaft. Then slide the shaft back to the clamp and re-tighten the packing gland. Hopefully that will give you enough room. Do all of the above when prepared and very little water will ingress. Be sure not to slide the shaft to far depending on prop to rudder clearance.

Dave Neptune
Reply With Quote
The Following User Says Thank You to Dave Neptune For This Useful Post:
W2ET (09-21-2022)
  #3   IP: 72.220.199.69
Old 09-21-2022, 09:43 PM
Boatjoc Boatjoc is offline
Member
 
Join Date: Jun 2022
Posts: 2
Thanks: 0
Thanked 0 Times in 0 Posts
Thanks for the welcome Dave, and thanks for the info. Needless to say, doing this with many gallons of ocean wanting inside my boat is intimidating. But I think I will go ahead and order the necessary parts an special tools and proceed.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Atomic 4 - Rear Oil Seal Replacement Administrator Helpful Videos 1 12-06-2020 11:32 AM
Rear oil seal replacement JackConnick Drive Train / Propellers 8 11-09-2020 10:23 PM
Leaking rear seal nesdon Troubleshooting 2 08-07-2019 12:00 PM
water pump seal replacement sailhog Cooling System 18 05-01-2015 05:00 PM
Rear shaft oil seal replacement Gari Tartan 18 11-07-2013 03:59 PM


All times are GMT -4. The time now is 08:52 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2022, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2022 Moyer Marine Inc.

All Rights Reserved