Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Discussion Topics > General Maintenance

Reply
 
Thread Tools Display Modes
  #1   IP: 68.9.169.239
Old 04-25-2021, 04:58 PM
tritonyawl2 tritonyawl2 is offline
Senior Member
 
Join Date: Apr 2007
Location: Bristol, RI, US
Posts: 18
Thanks: 12
Thanked 5 Times in 3 Posts
Relocate the Water Pump

For over 20 years the location of the water pump on my boat has been a torture. There are only 2 bolts and 2 hoses that must be removed to get this water pump out. Years ago I installed the long bolt Moyer offered for the bottom bolt. I even put in a much larger hatch (17 x 24) to have better access. Both improvements helped, but it is still a bear of a job.

So this year I bought the impeller puller with high hopes. So far the four screws holding the cover are not cooperating after 2 days of PB Blaster. In my case the gear shift is in the way as well as the intake seacock and some plumbing. But the screws are not moving.

I'd be willing to pay a lot if the pump could be relocated near the front of the engine. The flywheel shaft or the alternator belt are a couple possible sources of power. Or even an electric pump would be a godsend.

Replacing the impeller is by far the worst job on my boat. It can take a couple hours. And I don't want to think about the impeller ever letting go while motoring with no wind. You'd have to remove the pump no matter the conditions.

Sorry for the rant. My boat may have this worse than others. The Atomic 4 and Moyer's service are great and I'm grateful for both. And I'm hopeful the 4 screws will eventually turn. Anyone else tired of dealing with this problem?
Reply With Quote
  #2   IP: 67.169.215.221
Old 04-25-2021, 05:42 PM
ronstory's Avatar
ronstory ronstory is offline
Afourian MVP
 
Join Date: Feb 2016
Posts: 404
Thanks: 106
Thanked 208 Times in 152 Posts
Regarding the stubborn screws, do you have space to use a good old impact screwdriver?

https://www.harborfreight.com/6-bit-...caAlfVEALw_wcB

Also, while changing the impeller does qualify as a yoga class session, it's a 30-40 min job for me on our boat. That said, I'm using a Moyer pump with sealed bearings (no grease cup ) and captive thumbwheels on the cover.

I just remove the cover using fingers only (and a towel), grab the impeller with a short a needlenose, wiggle and yank. Note the orientation of the slot during removal for easy installation. The shaft comes out and I replace the impeller from the comfort of the counter put a touch a synthetic grease on the shaft and then slide back in.

The only tricky thing is making sure the rubber O-ring in the cover stays in the groove. I help with retention using a bit of synthetic grease to keep things in place and on the threads of the thumbscrews.

The thumbscrew cover is simply a godsend.

I also wondered if you really need the retention clip with the impeller being captive in the chamber, as is the shaft via aux drive. That said, I still haven't be brave enough to skip it.
__________________
Thanks,
Ron
Portland, OR

Last edited by ronstory; 04-28-2021 at 10:59 AM. Reason: typos
Reply With Quote
The Following User Says Thank You to ronstory For This Useful Post:
tritonyawl2 (04-25-2021)
  #3   IP: 68.9.169.239
Old 04-25-2021, 06:07 PM
tritonyawl2 tritonyawl2 is offline
Senior Member
 
Join Date: Apr 2007
Location: Bristol, RI, US
Posts: 18
Thanks: 12
Thanked 5 Times in 3 Posts
Thanks, Ron. Very good suggestions. Will get that impact driver tomorrow. I think it might fit. And when I get the pump or cover out, will replace with the thumb screw cover. I like finger screws.

Just discovered there is an electric replacement. Still requires raw sea water. Expensive but may be a good idea. Why not a closed system - radiator with fan like a car?
Reply With Quote
  #4   IP: 67.169.215.221
Old 04-25-2021, 07:56 PM
ronstory's Avatar
ronstory ronstory is offline
Afourian MVP
 
Join Date: Feb 2016
Posts: 404
Thanks: 106
Thanked 208 Times in 152 Posts
It does not take much force on the impact drives. Just spin counter-clockwise on the screw to take up any slack in the rotation before you whack it.

Interesting. Who makes an electric version? I would be curious of the design since with a waterlift muffler, the flow likely needs to vary with engine RPM. With one a constant speed, you could risk flooding the motor due to not enough exhaust pressure (eg. idle) or alternatively too low of flow for high RPM cooling.
__________________
Thanks,
Ron
Portland, OR
Reply With Quote
The Following User Says Thank You to ronstory For This Useful Post:
tritonyawl2 (04-25-2021)
  #5   IP: 104.174.83.118
Old 04-25-2021, 09:30 PM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
  1. Relocate the pump: More like abandon the inaccessible engine mounted pump and install a PTO pedestal mounted pump driven off the flywheel, same as the Moyer fresh water cooling system uses. There is nothing to re-engineer, all the parts are available. If I were considering this, I'd remove the original pump for good and fashion a blank plate in its place, gasketed of course.
  2. Electric raw water pump: I'll repeat the point Ron made, depending on exhaust type you may require proportionate flow to the engine RPM and corresponding exhaust flow. If your exhaust is a straight pipe, stand pipe or water jacketed, no problem with full flow regardless of engine RPM. If it's a waterlift, proportionate flow becomes critical.
  3. Automotive cooling system with a radiator: You won't have sufficient air flow to keep up with the engine heat. It's not like your radiator is cruising down the highway with 80 MPH worth of air running through it.
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others
Reply With Quote
The Following 3 Users Say Thank You to ndutton For This Useful Post:
sastanley (04-26-2021), TimBSmith (04-26-2021), tritonyawl2 (04-25-2021)
  #6   IP: 68.9.169.239
Old 04-25-2021, 10:57 PM
tritonyawl2 tritonyawl2 is offline
Senior Member
 
Join Date: Apr 2007
Location: Bristol, RI, US
Posts: 18
Thanks: 12
Thanked 5 Times in 3 Posts
Thanks! the PTO pedestal mounted pump is worth investigation. Electric sounds possible, but would require more engineering.

Last edited by tritonyawl2; 04-28-2021 at 08:58 AM.
Reply With Quote
  #7   IP: 47.142.139.236
Old 04-26-2021, 12:26 AM
JOHN COOKSON JOHN COOKSON is offline
Afourian MVP, Professor Emeritus
 
Join Date: Nov 2008
Posts: 3,500
Thanks: 54
Thanked 855 Times in 629 Posts
I finally gave up on the cover screws on the H2O pump and went to bolts that I could get a 1/4" socket on. Life was much happier afterwards.

ex TRUE GRIT

Last edited by JOHN COOKSON; 04-26-2021 at 12:29 AM.
Reply With Quote
The Following User Says Thank You to JOHN COOKSON For This Useful Post:
tritonyawl2 (04-26-2021)
  #8   IP: 69.250.111.245
Old 04-26-2021, 10:41 AM
sastanley's Avatar
sastanley sastanley is online now
Afourian MVP
 
Join Date: Sep 2008
Location: Solomons, MD
Posts: 7,016
Thanks: 1,134
Thanked 600 Times in 442 Posts
What Ron & Neil said. You can simply abandon that pump and let it spin away, and either mount something to run off the flywheel (Moyer has the bracket, https://moyermarine.com/product/seaw...nting-bracket/), or Indigo makes a mount to hold a Moyer pump in between the alternator and accessory drive pulley (part of one of their FWC system), but I assume you can buy just the bracket if you didn't want to fabricate something.
__________________
-Shawn
"Holiday" - '89 Alura 35 #109
"Twice Around" - '77 C-30, #511 with original A-4 & MMI manifold - SOLD! (no longer a two boat owner!!)
http://www.moyermarine.com/forums/signaturepics/sigpic3231_6.gif
Reply With Quote
The Following User Says Thank You to sastanley For This Useful Post:
TimBSmith (04-26-2021)
  #9   IP: 68.9.169.239
Old 04-26-2021, 11:54 AM
tritonyawl2 tritonyawl2 is offline
Senior Member
 
Join Date: Apr 2007
Location: Bristol, RI, US
Posts: 18
Thanks: 12
Thanked 5 Times in 3 Posts
FWC is sounding better if you can just abandon the existing Oberdorfer pump and run the hoses to the new system which is in a easier to reach location.

The FWC they offer here does not provide a lot of detail. I'd like to see a very detailed article on how to plan and install it.
Reply With Quote
  #10   IP: 67.169.215.221
Old 04-26-2021, 01:09 PM
ronstory's Avatar
ronstory ronstory is offline
Afourian MVP
 
Join Date: Feb 2016
Posts: 404
Thanks: 106
Thanked 208 Times in 152 Posts
Indigo has two FWC systems, one mechanical and one with an electric pump.

I'm using the electric version and I just upgraded to their latest electic pump during my rebuild a few months back.
__________________
Thanks,
Ron
Portland, OR

Last edited by ronstory; 04-26-2021 at 01:12 PM. Reason: typo, always typos
Reply With Quote
The Following 3 Users Say Thank You to ronstory For This Useful Post:
sastanley (04-26-2021), TimBSmith (04-26-2021), tritonyawl2 (04-27-2021)
  #11   IP: 104.174.83.118
Old 04-26-2021, 05:34 PM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
FWC requires two pumps (1@ raw water and 1@ antifreeze) any way you decide to go therefore the previous proportional raw water concerns apply.
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others
Reply With Quote
The Following 2 Users Say Thank You to ndutton For This Useful Post:
sastanley (04-26-2021), tritonyawl2 (04-27-2021)
  #12   IP: 69.250.111.245
Old 04-26-2021, 08:43 PM
sastanley's Avatar
sastanley sastanley is online now
Afourian MVP
 
Join Date: Sep 2008
Location: Solomons, MD
Posts: 7,016
Thanks: 1,134
Thanked 600 Times in 442 Posts
sorry..didn't mean to confuse the issue. I was thinking about taking the MMI pump that Indigo makes a mount for, and install it in the alternator loop to help with your access issue. If you wanted FWC you'd need a 2nd pump regardless. The belt driven for raw water, and an electric pump for antifreeze is a definite possibility.
__________________
-Shawn
"Holiday" - '89 Alura 35 #109
"Twice Around" - '77 C-30, #511 with original A-4 & MMI manifold - SOLD! (no longer a two boat owner!!)
http://www.moyermarine.com/forums/signaturepics/sigpic3231_6.gif

Last edited by sastanley; 04-26-2021 at 08:46 PM.
Reply With Quote
  #13   IP: 67.169.215.221
Old 04-27-2021, 12:11 AM
ronstory's Avatar
ronstory ronstory is offline
Afourian MVP
 
Join Date: Feb 2016
Posts: 404
Thanks: 106
Thanked 208 Times in 152 Posts
This is just my opinion, but one of the things I really like about our A4 is in its base form, is there are zero exposed spinning parts on the "front" of the motor.

We've all had to debug issues on running motors, and for me, a cat in a roomful of rocking chairs comes to mind. With the A4, being able to lean over and fiddle with things where the only thing I have to worry about is the alternator belt on the back of the engine... is IMO an understated plus.

I never have the worry of "pulling a Frodo" and ending up with less than 10.
__________________
Thanks,
Ron
Portland, OR

Last edited by ronstory; 04-27-2021 at 12:28 PM. Reason: grammar
Reply With Quote
  #14   IP: 68.9.169.239
Old 04-28-2021, 08:59 AM
tritonyawl2 tritonyawl2 is offline
Senior Member
 
Join Date: Apr 2007
Location: Bristol, RI, US
Posts: 18
Thanks: 12
Thanked 5 Times in 3 Posts
The more I think of it, relocating the pump is the best solution. I would like to remove the Oberdorf and move it to the flywheel. Connect the flywheel shaft directly to the water pump shaft and lengthen the two hoses.

Why add a second pump?

Think you'd have to bolt the pump to the flywheel cover, but the main challenge is connecting the two shafts. What do think? Some minor carpentry would be required. Checking the impeller would take 5 minutes and would be laughably easy.
Reply With Quote
  #15   IP: 104.174.83.118
Old 04-28-2021, 09:48 AM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
Quote:
Originally Posted by tritonyawl2 View Post
Why add a second pump?
The two pump discussion had to do with FWC only.

Quote:
Originally Posted by tritonyawl2 View Post
Think you'd have to bolt the pump to the flywheel cover, but the main challenge is connecting the two shafts.
If your flywheel cover is the heavy casting, that sounds like a viable plan to me. Also, transferring the pump's torque load to all of the smaller flywheel cover bolts would be good. If the flywheel cover is the newer sheet metal design, a heavier bracket will need to be fabricated and would do well to be fastened (again) by ALL the flywheel cover bolts.

MMI offers a crankshaft PTO adapter that may be a good place to start.
https://moyermarine.com/product/pto-shaft-cfwc_10_184/
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others
Reply With Quote
The Following User Says Thank You to ndutton For This Useful Post:
tritonyawl2 (04-28-2021)
  #16   IP: 69.250.111.245
Old 04-28-2021, 01:09 PM
sastanley's Avatar
sastanley sastanley is online now
Afourian MVP
 
Join Date: Sep 2008
Location: Solomons, MD
Posts: 7,016
Thanks: 1,134
Thanked 600 Times in 442 Posts
I don't know this for sure, but I think you risk exposing the oil system if there is no pump attached to the back of the accessory drive. I am pretty sure engine oil lubricates the shaft up to the first shaft seal inside the pump.

A block off plate, similar to what is used when the mech. fuel pump is removed in favor of electric, may fix that problem. You'd have to fabricate something I think..not sure a 'water pump delete plate' exists.
__________________
-Shawn
"Holiday" - '89 Alura 35 #109
"Twice Around" - '77 C-30, #511 with original A-4 & MMI manifold - SOLD! (no longer a two boat owner!!)
http://www.moyermarine.com/forums/signaturepics/sigpic3231_6.gif

Last edited by sastanley; 04-28-2021 at 01:13 PM.
Reply With Quote
The Following User Says Thank You to sastanley For This Useful Post:
tritonyawl2 (04-28-2021)
  #17   IP: 68.9.169.239
Old 04-28-2021, 04:40 PM
tritonyawl2 tritonyawl2 is offline
Senior Member
 
Join Date: Apr 2007
Location: Bristol, RI, US
Posts: 18
Thanks: 12
Thanked 5 Times in 3 Posts
I think that plate would be easy to make and I would use the same gasket that is used for the pump. One question is whether the pump can turn counter clockwise as I believe the flywheel turns? If not, my plan won't work.
Reply With Quote
The Following User Says Thank You to tritonyawl2 For This Useful Post:
sastanley (04-28-2021)
  #18   IP: 104.174.83.118
Old 04-28-2021, 05:01 PM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
The pump can turn either way but your inlet and outlet ports reverse.
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others
Reply With Quote
The Following User Says Thank You to ndutton For This Useful Post:
tritonyawl2 (04-28-2021)
  #19   IP: 68.9.169.239
Old 06-13-2021, 03:30 PM
tritonyawl2 tritonyawl2 is offline
Senior Member
 
Join Date: Apr 2007
Location: Bristol, RI, US
Posts: 18
Thanks: 12
Thanked 5 Times in 3 Posts
Moyer PTO pump is the answer

I finally installed the Moyer PTO pump and removed the very hard-to-reach leaking Oberdorffer pump. Had a 1/4 inch steel plate custom-made to cover that hole (a rectangle would not fit). Had to tap the bottom bolt hole (had been using Moyer's long bolt). Replaced and re-routed all the hoses. To replace the hose that goes into the water jacket, I had to remove the water jacket. Discovered two water jacket bolts that were stripped. So installed two Moyer replacements (unfortunately at two different times

Replaced the pipe that goes into the water jacket with a longer one so I can actually reach the hose clamp. This makes checking the oil a little harder, but much peace of mind that I can now tighten or replace the hose clamp anytime.

The engine runs great on the hard. Just waiting for the truck to splash the boat. The Moyer kit to mount the PTO pump is very well designed. I should have done this years ago. All these years of worrying about and cursing the old waterpump and it's location. Now I can check or replace the impellar or even the pump in a few minutes without swearing. I'm half way to a fresh water cooling system, but am in no hurry at least not this year.

Just wanted to wrap up this story and thank all those who helped including those on the forum and Don Moyer and Ken and Tom Stevens. Ready for a summer of sailing fun and adventures!
Reply With Quote
Reply

Tags
impeller, water pump

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Water Pump Mystery - Running out of ideas Clucas Troubleshooting 15 05-16-2013 09:16 PM
Leaking MMI Water Pump Bruce A Cooling System 5 08-24-2011 12:25 PM
leaking water pump rogers jolly General Interest 9 04-25-2011 08:49 PM
universal UJ-61 water pump Dromo General Interest 5 05-09-2010 10:37 AM
Raw Water pump failure in FWC system Tom Witzel Cooling System 0 07-25-2006 11:21 AM


All times are GMT -4. The time now is 07:58 PM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2024 Moyer Marine Inc.

All Rights Reserved