Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Owner Discussion Groups > Discussion Groups > Morgan

Reply
 
Thread Tools Display Modes
  #1   IP: 69.105.31.123
Old 03-12-2009, 08:09 PM
Paul K Paul K is offline
Member
 
Join Date: Jan 2008
Posts: 2
Thanks: 0
Thanked 0 Times in 0 Posts
Vacum gauge at zero.....

I have a '72 Ranger with an Atomic motor. We took it out to fish off of this past Sunday, and during the first putt up the coast, there was a strong gas/oil smell in the cabin, to the point where we all had to sit outside. When the motor wasn't running, the smell went away. The oil pressure is at a steady 40lbs, the water temp. is at a steady 140 degrees, the amp gauge reads about 2 volts to the positive, and the vacum gauge reads zero.

First, what is the vacum used for in this application, and what should it be reading?

The boat is in So Cal, in San Pedro.

Paul K
Reply With Quote
  #2   IP: 138.88.162.86
Old 03-12-2009, 08:18 PM
msauntry's Avatar
msauntry msauntry is offline
 
Join Date: May 2008
Location: Annapolis, MD
Posts: 505
Thanks: 0
Thanked 1 Time in 1 Post
Check your oil level and see if it is unusually high and smells like gas. If you have a mechanical fuel pump, the seal may have leaked. This would allow gas from the carb to mix with the oil in the crankcase, which would then get vented to the outside through the crankcase vent (tube above the carb flame arrestor). Check the carb for obvious leaks as well. Be carefull of sparks and run the blower when working on it.

Haven't seen a vacuum gauge mounted on an a4 b4...
Reply With Quote
  #3   IP: 144.160.130.16
Old 03-13-2009, 08:24 AM
rheaton rheaton is offline
Senior Member
 
Join Date: Aug 2005
Location: Rockaway, NJ
Posts: 134
Thanks: 0
Thanked 0 Times in 0 Posts
You might want to add an inline bulp fuel pump in the line. This will allow you to preasurize the system and hopefuly detect any fuel leak.
Reply With Quote
  #4   IP: 64.203.32.52
Old 03-13-2009, 10:02 AM
Dave Neptune Dave Neptune is offline
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Lake Arrowhead Ca.
Posts: 4,533
Thanks: 571
Thanked 784 Times in 529 Posts
Smile Vacuum

Paul, the vacuum guage tells you how hard the intake manifold is working. The guage should not read "O" unless the engine is off. At idle you should show around 15-18 inches of vac. As you increase the load on the engine (throttle up) in gear the guage will drop towards zero at (your affective) full throttle. If the guage isn't moving it could be the line that feeds it is leaking or even missing. If you get the guage working it will prove to be very valuable for tuning and knowing how the engine is performing. It is a good diagnostic tool for a gas engine. We'll need a little more info to figure out the gas smell, then we can show you how to utalize the Vac-guage. I to am in So Cal and headed to Newport for a 30 plus "Wagon wheel raft-up" for the weekend. I'll chime in again on monday when I have the time to explain the use of the Vac-guage for tuning and crusing!

David
Volador E-35MkII 1970 original A-4
Reply With Quote
  #5   IP: 12.47.208.34
Old 03-13-2009, 02:31 PM
tenders tenders is offline
Afourian MVP
 
Join Date: May 2007
Location: Harlem YC, City Island, NY
Posts: 1,413
Thanks: 41
Thanked 232 Times in 153 Posts
I would be interested to know how/where to install a vacuum gage onto an A4.

Hey, Don has no kit for this already??!?
Reply With Quote
The Following User Says Thank You to tenders For This Useful Post:
twofreddy (06-02-2017)
  #6   IP: 64.203.32.52
Old 03-16-2009, 12:34 PM
Dave Neptune Dave Neptune is offline
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Lake Arrowhead Ca.
Posts: 4,533
Thanks: 571
Thanked 784 Times in 529 Posts
Thumbs up Vacuum guage

tenders, I installed mine at the "scavange line hook up port" on the side of the intake manifold. All I needed to do was install a Tee fitting and run the tube to the guage. I am truly amazed that more are not using a Vac/guage as it is the only way you can measure what the carburator is feeding the engine. I spent a few years working on a dyno and a flow bench while building racing engines anything from cosworths to big blocks single cylinder to an old V-16 (Caddy) and even a few "Rotaries". In measuring a gain in performance you need to be able to measure what you are "feeding" the engine at a given rpm to see if you made a gain with what ever you changed. Otherwise all you can evaluate is how much power you are making and not how much power you gained at a specific carb feed rate at a given rpm. The Vacuum guage is the first thing I installed when I bought mine.
I usually cruise with my engine by increasing the throttle to a specific Vacuum reading of 7" which gives me hull speed. When the speed levels off and I am at 7" of Vac. and I am at a lower rpm than before I know something is amiss dirty prop or a tuning problem is beginning to show up. If I make a modification or adjustment and gain a hundred rpm or so at the same Vac value I have made a gain or visa/versa. It is especially valuable to those who tinker to make gains in power or fuel consumption, otherwise you really don't have a baseline to measure your gains since you can just apply a little more throttle and get the same rpm. The engine should perform the same at a given rpm and vac/value or something changed via your tinkering or something is going amiss.

David
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Temperature Gauge Sending Unit Jesse Delanoy Cooling System 6 10-25-2008 08:41 AM
Stewart Warner oil pressure gauge electrical charles@pricefarrington.c General Maintenance 2 09-17-2008 05:21 PM
Sticky Gauge Pointers High Hopes General Interest 0 05-18-2008 10:33 AM
Temperature gauge problems? omec Cooling System 0 07-16-2007 01:37 PM
Nonfunctioning water temp gauge Unregistered Electrical 4 08-01-2005 12:46 AM


All times are GMT -4. The time now is 05:46 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2022, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2022 Moyer Marine Inc.

All Rights Reserved