Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Testing Protocols

Reply
 
Thread Tools Display Modes
  #1   IP: 32.211.28.40
Old 12-04-2020, 07:05 PM
Al Schober's Avatar
Al Schober Al Schober is offline
Afourian MVP
 
Join Date: Jul 2009
Location: Uncasville, CT
Posts: 1,802
Thanks: 11
Thanked 401 Times in 297 Posts
Diagnosing shifting issues

Having shifting issues? If you don't know whether you have a transmission issue or a problem with the linkage, I recommend the following:
With the engine off, remove the reversing gear cover. As you (or a helper) move your shift lever, you'll see the shifter cone around the main shaft move fwd (towards the engine block) and aft.
With the shifter in fwd gear, you should see the cone move AFT and engage the three fingers that engage the fwd clutch pack. The fingers should go over the hump in the cone and kinda snap into place. If this doesn't happen, you can try loosening the adjustment for the fwd clutch pack and try again. If it still doesn't go, your shift linkage is faulty or out of adjustment. Once you get it to shift fully into fwd, you can re-tighten the clutch pack.
Move the shifter to the reverse position - you'll see the cone move fwd. It should almost come into contact with the notched ring for adjusting the fwd clutch pack. 1/32 or 1/16 of clearance is fine. If the cone contacts the notched ring, you should tighten the reverse adjusting nut. If your clearance is more than 1/16", try backing off the reverse adjusting nut a few flats and try again. If you can't get the cone to move this far fwd, your shifter is likely faulty/out of adjustment. You can alway tighten up the reverse adjustment.
Making adjustments to the reversing gear to compensate for a faulty shifter is futile and likely to damage the reversing gear. At best, you'll have little/no neutral band.
Reply With Quote
The Following 6 Users Say Thank You to Al Schober For This Useful Post:
alcodiesel (12-10-2020), chapster5 (12-06-2020), edwardc (12-05-2020), Sam (12-06-2020), Surcouf (12-06-2020), TimBSmith (12-04-2020)
  #2   IP: 12.216.108.66
Old 12-07-2020, 11:23 AM
Indy Indy is offline
Senior Member
 
Join Date: Oct 2014
Posts: 21
Thanks: 6
Thanked 0 Times in 0 Posts
Thanks for this advice. It seems like our forward clutch slips when we throttle up with the boat moving at around 5knots. The previous owner thought it was the prop cavitating- is there a way to know for sure? For what it's worth, this is the original two blade prop, which is very clean.

Also, from reading and watching the tech tip video, I assume there is no affect on reverse if I move the FWD adjusting nut by a notch. Correct?
Reply With Quote
  #3   IP: 32.211.28.40
Old 12-07-2020, 05:15 PM
Al Schober's Avatar
Al Schober Al Schober is offline
Afourian MVP
 
Join Date: Jul 2009
Location: Uncasville, CT
Posts: 1,802
Thanks: 11
Thanked 401 Times in 297 Posts
The Navy uses hydrophones to detect cavitation. I didn't have much interest in going that way but it would be fun just to see what you could hear at an anchorage in the evening. Another fun thing I've gone with the younger folk is to put a spotlight shining into the water and let them see what the light attracts. Better than video games!
I'd just tighten one notch and see the affect. And no, such an adjustment won't affect reverse.
Reply With Quote
  #4   IP: 12.216.108.66
Old 12-07-2020, 07:15 PM
Indy Indy is offline
Senior Member
 
Join Date: Oct 2014
Posts: 21
Thanks: 6
Thanked 0 Times in 0 Posts
Quote:
Originally Posted by Al Schober View Post
The Navy uses hydrophones to detect cavitation. I didn't have much interest in going that way but it would be fun just to see what you could hear at an anchorage in the evening. Another fun thing I've gone with the younger folk is to put a spotlight shining into the water and let them see what the light attracts. Better than video games!
I'd just tighten one notch and see the affect. And no, such an adjustment won't affect reverse.
Too bad my underwater recording studio idea never really took off.
Thanks for the response. I wish it were easy to get to, but the shifting cable bracket is attached via the starboard bolts on the transmission cover, plus it's a very tight squeeze. I may need a spotter on hand to pull me out by my ankles.
Reply With Quote
  #5   IP: 32.211.28.40
Old 12-07-2020, 08:01 PM
Al Schober's Avatar
Al Schober Al Schober is offline
Afourian MVP
 
Join Date: Jul 2009
Location: Uncasville, CT
Posts: 1,802
Thanks: 11
Thanked 401 Times in 297 Posts
Yeah, backing out from somewhere is always a concern. I remember crawling into a cranny on a submarine to look at something and I couldn't get back out. Turns out a valve handwheel had gotten into my pocket!
I'd suggest a) grease, and b) get naked - but then you'd have to post photos.
Reply With Quote
  #6   IP: 12.216.108.66
Old 12-08-2020, 07:12 AM
Indy Indy is offline
Senior Member
 
Join Date: Oct 2014
Posts: 21
Thanks: 6
Thanked 0 Times in 0 Posts
That is some naked you don't want to see, I assure you.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Shifting Cable System Issues Administrator Reversing Gear 0 08-01-2019 07:54 AM
Shifting Cable System Issues Administrator Announcements 0 08-01-2019 07:47 AM
Forward and Reverse Gear Adjustment Issues CraigRun Reversing Gear 12 05-17-2012 09:15 PM
New Atomic 4 owner with shifting issues lchirichigno Troubleshooting 13 08-30-2011 03:19 PM
Shifting from foward to neutral sterling8008 Troubleshooting 1 10-06-2006 10:04 AM


All times are GMT -4. The time now is 06:45 PM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2021, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2021 Moyer Marine Inc.

All Rights Reserved