Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Discussion Topics > General Maintenance

Reply
 
Thread Tools Display Modes
  #1   IP: 64.137.150.147
Old 07-19-2021, 10:44 AM
donoharm donoharm is offline
Frequent Contributor
 
Join Date: Oct 2020
Posts: 5
Thanks: 1
Thanked 0 Times in 0 Posts
Is this safe?

Hello, Iím the new owner of an Atomic 4 powered C&C 30. While looking around in the engine bay, I noticed some corrosion on the engine block. The engine works like a champ, but Iím a little concerned about the level of corrosion on the block. My questions for the forum are:

1) Is this normal?
2) is this safe?
3) what, if anything should be done to remediate it?
Attached Images
   
Reply With Quote
  #2   IP: 207.32.171.10
Old 07-19-2021, 11:23 AM
capnward's Avatar
capnward capnward is offline
Afourian MVP
 
Join Date: Aug 2012
Location: Deer Harbor WA
Posts: 285
Thanks: 25
Thanked 109 Times in 84 Posts
Rust like that is normal with people who don't take care of their engine. It is safe for now, as long as it doesn't spray water in that area. You are right to be concerned about the level of corrosion. As long as your engine runs well, and is not leaking water from that corroded water jacket side plate, you might as well enjoy it this summer. But you will eventually need to remove the engine from the boat to deal with all that rust and repaint the engine. It would make a good winter project. There is probably plenty of metal left under the rust, but you will need a new water jacket plate. I suspect the reason for the rust is the side plate has leaked in the past, or the hose fitting into it. I am guessing you have a raw water cooled engine, and the side plate has been leaking salt water for a while. The block is probably still ok, but you will have to make sure. Change to fresh water cooling and corrosion like this is less likely.
Reply With Quote
  #3   IP: 138.207.177.95
Old 07-19-2021, 12:34 PM
joe_db's Avatar
joe_db joe_db is online now
Afourian MVP
 
Join Date: May 2009
Posts: 3,878
Thanks: 49
Thanked 629 Times in 463 Posts
Safe as in won't blow up - sure.
You do need to get rid of the leaks causing that rust and then fix the rust
Reply With Quote
  #4   IP: 32.211.28.40
Old 07-19-2021, 04:53 PM
Al Schober's Avatar
Al Schober Al Schober is offline
Afourian MVP
 
Join Date: Jul 2009
Location: Uncasville, CT
Posts: 1,815
Thanks: 11
Thanked 409 Times in 302 Posts
That leakage at the side plate is common, and is caused by the 8 bolts. It's nigh impossible to get the threads of the bolts to seal. Best fix is to change to studs and nuts. Our host sells a kit for this job. When the plate is off, you can evaluate the degree of corrosion on the back side (plan on replacing it).
I notice our host is sold out on the stud kits. Make up your own kit from some stainless set screws, stainless nuts, and some JB Weld.

Last edited by Al Schober; 07-19-2021 at 04:57 PM.
Reply With Quote
  #5   IP: 165.225.20.156
Old 07-19-2021, 05:39 PM
Surcouf's Avatar
Surcouf Surcouf is online now
Afourian MVP
 
Join Date: May 2018
Posts: 312
Thanks: 251
Thanked 126 Times in 97 Posts
Welcome!

as mentioned by the others:
- not unsafe
- can "easily" be recovered to a very good state: at the end of the season (do not waste a single day out of 2021), be ready with the proper material (new plate + stud kit etc...). Remove alternator + starter, clean / brush / chisel out the rust, treat rust, paint, and install new plate with Permatex etc.. There are many threads on this forum that will show much more rust (way more sometimes), and help you perform that very satisfactory repair.

the absolute key on the A4 is to treat and solve any leak, to prevent sea water from rusting the block.

our host will also help you on supply, parts etc...
Good luck
__________________
Surcouf
A nostalgic PO - Previously "Almost There" - Catalina 27 (1979)
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
De-winterizing- When is it safe? Ajax General Interest 25 04-21-2015 08:25 PM
Just when I thought it was safe... Skywalker Troubleshooting 10 08-03-2014 04:08 PM
Be safe out there! roadnsky Fuel System 2 09-29-2012 01:44 PM
Reply to safe operating temperature ArtJ Troubleshooting 30 07-23-2010 05:59 AM
Safe Operating Temps Paul Clarke General Interest 0 07-19-2010 11:29 PM


All times are GMT -4. The time now is 10:04 PM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2021, vBulletin Solutions, Inc.


Universalģ is a registered trademark of Westerbeke Corporation

Copyright © 2004-2021 Moyer Marine Inc.

All Rights Reserved