Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Discussion Topics > Exhaust System

Reply
 
Thread Tools Display Modes
  #1   IP: 24.22.118.150
Old 12-02-2008, 02:11 AM
bigd14 bigd14 is offline
Frequent Contributor
 
Join Date: Oct 2008
Posts: 8
Thanks: 0
Thanked 0 Times in 0 Posts
Exhaust Riser Question

Hey everyone-

I've started to address the exhaust system on my raw-water cooled Atomic 4 in my 1972 Ericson 27. It looks like its been poorly cobbled together, with a very loose attachment to the manifold (at least it came off easily!) and no support or anchors anywhere. The exhaust exits the manifold and almost immediately enters an aluminum exhaust riser, where the cooling water is injected. It then leads aft to an old plastic water lift muffler, and then up a long length of hose to the top of the port lazarette locker and out the stern. See the attached photos.

I've been wondering if the aluminum exhaust riser/elbow (Barr Mfg model 20-0101/20-0094) has been installed backwards- it appears that the cooling water enters on the wrong side of the riser and higher than the manifold! In all the exhaust diagrams I have seen, cooling water is supposed to be injected on the downstream end below the level of the exhaust manifold, but then I have never seen this type of exhaust riser used either. Is using this type of riser even a valid installation method for a gas engine? Has anyone seen a similar setup?

If anyone has any advice on this current system or what I should do for a new system, or photos and/or descriptions of their currently functioning systems I would really appreciate it!

Thanks,


Doug
Attached Images
  
Reply With Quote
  #2   IP: 142.68.114.60
Old 12-02-2008, 08:18 AM
rigspelt's Avatar
rigspelt rigspelt is offline
Afourian MVP
 
Join Date: May 2008
Posts: 1,187
Thanks: 0
Thanked 19 Times in 17 Posts
I'm not an expert. Interesting system, great photos.
1. I wonder if the riser is correctly installed, and the cooling water only mixes with the exhaust gasses inside that riser on the far (down) side after going over the top? Perhaps there is a jacket system on the near (up) side that starts cooling the gasses before mixing with the water on the far side, before entering the pipe to the waterlift muffler?
2. I don't understand the blocked off port on the bottom of that riser. Maybe it is an optional port?

Is there a manufacturer's name or part number stamped on the riser? Googling them could help.

I did not find a riser quite like that when I searched for available options among currently available models, but it would solve my exhaust problems nicely if they are still available. I shall follow this with interest.
__________________
1974 C&C 27
Reply With Quote
  #3   IP: 66.161.32.165
Old 12-02-2008, 09:42 AM
luvmyi36 luvmyi36 is offline
Senior Member
 
Join Date: Jun 2007
Location: Carlsbad, Ca
Posts: 117
Thanks: 0
Thanked 0 Times in 0 Posts
Doug,
not sure about your question, but it looks like you are lacking an anti siphon device. On mine, it is in the rubber hose exiting the manifold before it mixes.. Adding one could save you future aggrivation. Just food for thought.
__________________
Jim
S/V Cayenne
1975 Islander 36
www.betterbmp.com
Reply With Quote
  #4   IP: 142.68.114.60
Old 12-02-2008, 10:09 AM
rigspelt's Avatar
rigspelt rigspelt is offline
Afourian MVP
 
Join Date: May 2008
Posts: 1,187
Thanks: 0
Thanked 19 Times in 17 Posts
Found it: looks like it is a Barr Marine Diesel mixing elbow: http://www.manifoldwarehouse.com/mes...rch=mani&id=18. Took about an hour. So I went to http://www.barrmarine.net/. They list two numbers for the Atomic 4: UV-1-259624, UV47-261050 but googling those numbers show they refer to the manifold and gasket, not riser. I found no other reference to that model except at manifoldwarehouse.

Here's the results of my search prior to making that hit:

Google image search:
Same riser shown here: http://www.yachtsurvey.com/exhaust_risers.htm. Notice the hose is fitted the same as yours (on the rising side).
This one makes me think it could be Westerbeke riser, since they made the Atomic 4: http://www.gulf32aeolus.blogspot.com/

So I went looking for Westerbeke or Universal exhaust riser/mixing elbows. Go here http://shop.torresen.com and search for their "universal exhaust riser" to see a similar model, though not the same.
Also http://www.go2marine.com/product.do?no=115172F

I found this information "The exhaust riser is a very common part used on many Yanmar engines up to 30 hp. Yanmar p/n 104214-13521 ($99.91). The inlet is left hand threads, so you will need an adaptor, Yanmar p/n 104214-13580 ($27.10). The riser may look strange because the water injection nipple is on the engine side. This is because there is a passage inside that dumps water out of the outlet side. This is a big advantage because the water cools the entire riser." at this page hhttp://www.ericsonyachts.org/infoex...ad.php?p=43352 which suggests how your mixing elbow/riser might be plumbed, perhaps.

The other thing I realized doing this search was that cobbling together galvanized pipe exhaust riser/mixing elbows on small sailboat engines must have come about as a cheaper solution than buying expensive elbows, and to get custom fits in some installations.
__________________
1974 C&C 27

Last edited by rigspelt; 12-02-2008 at 10:12 AM.
Reply With Quote
The Following User Says Thank You to rigspelt For This Useful Post:
W2ET (07-06-2021)
  #5   IP: 24.22.118.150
Old 12-02-2008, 09:37 PM
bigd14 bigd14 is offline
Frequent Contributor
 
Join Date: Oct 2008
Posts: 8
Thanks: 0
Thanked 0 Times in 0 Posts
Wow, Rigspelt, great info! I found the manufacturer to be Barr by Googling the numbers stamped on the side, but you've gone above and beyond- thank you! So it looks like the water intake may be in the correct position after all and this is not uncommon in diesel installations.

Jim, I'll have to look into the anti siphon issue- you're right, I have seen that in most of the diagrams too.

Now I just have to get brave and try to remove the fittings from this piece and see if its re-usable.

Thanks again.

Doug
Reply With Quote
  #6   IP: 207.200.112.99
Old 12-02-2008, 10:24 PM
adab1402 adab1402 is offline
Senior Member
 
Join Date: Mar 2007
Posts: 94
Thanks: 49
Thanked 4 Times in 2 Posts
just a tip

soak those fittings in atomic blaster for ease of deconstruction and use anti-sieze paste when reassembling . fair winds adab1402
Reply With Quote
The Following User Says Thank You to adab1402 For This Useful Post:
TimBSmith (10-10-2020)
  #7   IP: 174.31.118.47
Old 07-06-2021, 05:29 PM
wallis wallis is offline
Frequent Contributor
 
Join Date: Jun 2021
Posts: 6
Thanks: 7
Thanked 0 Times in 0 Posts
great info

I purchased an A4 with parts in a pile. This was in the pile. I had the same questions about it. Glad to have found this thread.

thanks
Attached Images
 
Reply With Quote
  #8   IP: 104.174.83.118
Old 07-06-2021, 11:16 PM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
That is a water jacketed elbow and the general design is not without liabilities, particularly internal salt crystallization and corrosion deposits. The attached picture is of a dissection of a different brand of water jacketed elbow of a similar design.
Attached Images
 
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others
Reply With Quote
The Following User Says Thank You to ndutton For This Useful Post:
Surcouf (07-07-2021)
  #9   IP: 134.41.132.177
Old 07-07-2021, 01:44 PM
Mo's Avatar
Mo Mo is offline
Afourian MVP
 
Join Date: Jun 2007
Location: Halifax NS,
Posts: 4,470
Thanks: 292
Thanked 411 Times in 272 Posts
I have an engine in my garage that came out of an Ericsson...pic attached. This particular engine is seized, was fresh water cooled but there is no oil showing on the stick. Same part is on this one though. I bought it anyway.
Attached Images
 
__________________
Mo

"Odyssey"
1976 C&C 30 MKI

The pessimist complains about the wind.
The optimist expects it to change.
The realist adjusts the sails.
...Sir William Arthur Ward.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
New exhaust system jsedivy Exhaust System 11 08-01-2011 07:50 PM
Believe I have stuck exhaust valves. Still have a question P30_889 Troubleshooting 101 06-11-2009 04:08 PM
question about removing water from the oil and smokey exhaust (yes I read the sticky) bluefreedom Troubleshooting 3 09-03-2007 10:43 PM
Bad exhaust design? raleighm Exhaust System 3 01-29-2007 08:22 AM
Stuck #4 Exhaust Valve: A special Tartan 30 problem? jellisfeingold Tartan 7 12-09-2006 03:11 PM


All times are GMT -4. The time now is 07:22 PM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2024 Moyer Marine Inc.

All Rights Reserved