|
#1
IP: 173.73.23.106
|
|||
|
|||
Shortening Transmission Shift Lever
The shift lever on my Rebuilt A-4 appears to be a few inches taller than the one it replaced and it is hitting my exhaust elbow before it can travel into forward gear. Rather than reconfigure my exhaust pipe, I am considering shortening 2 inches off the top of the lever so it clears the pipe.
Is it OK to shorten the lever by a few inches? Will it cause vibrations or reduce the force applied by the shift linkage? Any other way to modify? Appreciate any insights or experience. Thanks |
#2
IP: 107.77.97.121
|
||||
|
||||
Can't you swap the old one on?
Mine was sawn off by PO. It works. If you do cut it, I'd be sure to test it with some temporary clamp thing first to see if the leverage is still enough or too little. Russ old photo shows a little how it is
__________________
Whiskeyjack a '68 Columbia 36 rebuilt A-4 with 2:1 "Since when is napping doing nothing?" |
#3
IP: 137.200.32.22
|
||||
|
||||
If you are cutting above the attachment point you use, no worries
Not sure how it hits the exhaust, that is on the other side |
#4
IP: 32.211.28.40
|
||||
|
||||
The tranny shaft needs a certain amount of angular rotation to go into fwd/rev properly. The longer the shift arm is, the lower the forces will be but the higher the amount of cable travel needed. The standard shift cable will only give you 4" of travel (if I remember correctly).
Someone must know the correct arm length to use the 4" of travel. Anyone? I admit I'm a bit embarrassed that I don't know.. |
#5
IP: 73.132.159.159
|
|||
|
|||
The length of the lever doesn't matter as long as the attachment point remains the same distance from the transmission shifting shaft. They normally have two holes drilled through the lever, if you were and are using the second hole up, remove it from the engine and cut it off just above the holes. Hacksaw works just fine. Smooth the sharp edges with a file and touch up the paint.
If it is easier and still available, just swap the lever over from the old one. |
#6
IP: 173.73.23.106
|
|||
|
|||
Thanks for the responses. The engine, and original shaft have been returned, so too late to swap them. The shifter on my boat was always on the port side of the engine, which is also where my shift linkage is oriented.
From the responses, it seems OK to shave a little off the end of the shaft, as long as the attachment point for the linkage is not changed. Best to attach linkage and test that the linkage moves the shifter effectively before doing anything. If enough torque generated to go into reverse, just cut some from the shaft. Any other feedback is welcome. |
Tags |
hitting elbow, modifying, shifter, shortening |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Need Help With Belcrank Linkage For Cal 30 Shift Lever | captainmurph | Reversing Gear | 2 | 06-10-2015 01:44 AM |
Need Help With Belcrank Linkage For Cal 30 Shift Lever | captainmurph | Reversing Gear | 2 | 06-09-2015 10:33 PM |
shift lever is completely jammed due to poor winterizing I think | afsam94 | Reversing Gear | 8 | 07-23-2012 06:34 PM |
Shift cable/shift lever question. | Badger, C-27, N.H. | General Maintenance | 3 | 06-25-2006 08:39 PM |
Shift lever Stuck? | Getaway | Troubleshooting | 0 | 04-28-2006 04:45 PM |