Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Discussion Topics > Cooling System

Reply
 
Thread Tools Display Modes
  #1   IP: 73.234.59.26
Old 08-12-2020, 07:18 AM
southcoasting's Avatar
southcoasting southcoasting is offline
Senior Member
 
Join Date: Nov 2011
Location: Fairhaven, MA
Posts: 141
Thanks: 15
Thanked 22 Times in 13 Posts
Overheating due to coolant loss

I have searched the threads and have some ideas on what to look for but posting this so that others and myself could go through some learning of my process.

First off, this has been really frustrating! I have a brand new engine rebuild do at a local machine shop. New head, new exhaust manifold, new pistons, rings, bearings, heat exchanger, etc.

Been through a whole mess of things for since launching my boat with this new engine. Most recently, I am struggling with milky oil and me putting constant antifreeze into the system. Obviously, the antifreeze is getting into the oil at this point. I now have to figure out how/why...��

I know the typical steps but let me share some of my symptoms:

1. Engine is hard to start. Takes a lot of cranking before running
2. Plugs look black if taken out
3. Runs great after turning on but I have to keep putting af into heat exchanger due to leak

Obvious next steps will have to be pressure tests.

Could be my water pump...but doubt it since I have the Oberdorfer with the weep hole...but it just seems like the leak is substantial...like I have to fill heat exchanger every 10 mins or it runs dry...

Going to boat today but super frustrated at this point...
__________________
1971 Tartan 34C Sloop "NOVA LUNA", Rebuilt (2019) Fresh Water Cooled A4 (Bought boat in 2014)
1968 Tartan 27 Yawl "Destinada", rebuilt Old Lyme freshwater A4 (Sold boat in 2014)

Last edited by southcoasting; 08-12-2020 at 08:09 AM.
Reply With Quote
  #2   IP: 137.103.82.227
Old 08-12-2020, 08:46 AM
joe_db's Avatar
joe_db joe_db is online now
Afourian MVP
 
Join Date: May 2009
Posts: 4,474
Thanks: 49
Thanked 1,026 Times in 721 Posts
Yikes
Pressure test and compression test stat!
The best thing to find would be a head gasket needing replacement or maybe a hole in the manifold.
Reply With Quote
  #3   IP: 207.32.168.30
Old 08-12-2020, 09:04 AM
capnward's Avatar
capnward capnward is offline
Afourian MVP
 
Join Date: Aug 2012
Location: Deer Harbor WA
Posts: 335
Thanks: 41
Thanked 147 Times in 107 Posts
If your HX is draining in 10 minutes, that water has to be going somewhere, like into your crankcase. When it is running, check to see if your water pump is leaking out of the weep hole underneath the seals. I had mine leak so bad that it forced water into the crankcase through the accessory drive, as well as out the weep hole. The engine ran anyway, but overheated due to reduced coolant flow, as water was going other places besides the water jacket. The seals were shot. The bearings and shaft were replaced as well. If your local shop worked on the water pump, they may have installed the seals inside out, a common mistake. The engine being hard to start could be a different problem.
Attached Images
 
Reply With Quote
The Following User Says Thank You to capnward For This Useful Post:
TimBSmith (09-11-2020)
Old 08-12-2020, 09:17 AM
capnward
This message has been deleted by capnward.
  #4   IP: 155.186.124.219
Old 08-12-2020, 09:46 AM
Dave Neptune Dave Neptune is online now
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Grove, Oklahoma
Posts: 5,035
Thanks: 711
Thanked 1,289 Times in 839 Posts
First, how much is the oil level going up? It should be about as much as you are adding coolant.
The first check I would do is a compression check to check the head-gasket. If the compression check does not show a low cylinder it will be time for a leak-down test of the manifold and block. First check the manifold as it is easy to isolate then the block.
Since you stated that all the plugs are black I would suspect the manifold as the culprit.

Dave Neptune
Reply With Quote
  #5   IP: 155.186.124.219
Old 08-12-2020, 09:53 AM
Dave Neptune Dave Neptune is online now
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Grove, Oklahoma
Posts: 5,035
Thanks: 711
Thanked 1,289 Times in 839 Posts
Part II

If it is the pump leaking there should be a bit in the bilge and the plugs would look no different than usual as the coolant would be dumped directly into the oil pan.
In your case I suspect a breech as in my post above since your plugs are compromised. That indicates the coolant going through the combustion cycle and not just leaking into the oil.

Dave Neptune
Reply With Quote
  #6   IP: 137.103.82.227
Old 08-12-2020, 10:02 AM
joe_db's Avatar
joe_db joe_db is online now
Afourian MVP
 
Join Date: May 2009
Posts: 4,474
Thanks: 49
Thanked 1,026 Times in 721 Posts
If the engine was RWC you might see a different result,. It would not run out of coolant and overheat, it would just keep filling the crankcase.
*If* if is just a leaky pump, try re-plumbing to RWC with the non-leaky pump
Reply With Quote
  #7   IP: 174.255.69.70
Old 08-12-2020, 12:30 PM
southcoasting's Avatar
southcoasting southcoasting is offline
Senior Member
 
Join Date: Nov 2011
Location: Fairhaven, MA
Posts: 141
Thanks: 15
Thanked 22 Times in 13 Posts
Quote:
Originally Posted by Dave Neptune View Post
First, how much is the oil level going up? It should be about as much as you are adding coolant.
The first check I would do is a compression check to check the head-gasket. If the compression check does not show a low cylinder it will be time for a leak-down test of the manifold and block. First check the manifold as it is easy to isolate then the block.
Since you stated that all the plugs are black I would suspect the manifold as the culprit.

Dave Neptune
Oil level went up a lot! See dipstick pic attached. Twice over the full level. I looked underneath water pump and don’t see a big enough leak to indicate it is that

Thanks for the heads up Dave. Yeah, I had read in one of the billetins that hard starting are causes for a leaky manifold...so attached is a pic of the number 1 plug. Also, how do I pressure test manifold? It is as easy as plugging up the exhaust section and pumping in from the intake of manifold? If so, I just did a few pumps and I could hear swirling inside towards block and no pressure being held...bad manifold then? Do I have this correct?
Attached Images
  
__________________
1971 Tartan 34C Sloop "NOVA LUNA", Rebuilt (2019) Fresh Water Cooled A4 (Bought boat in 2014)
1968 Tartan 27 Yawl "Destinada", rebuilt Old Lyme freshwater A4 (Sold boat in 2014)

Last edited by southcoasting; 08-12-2020 at 12:33 PM.
Reply With Quote
  #8   IP: 174.255.69.70
Old 08-12-2020, 12:34 PM
southcoasting's Avatar
southcoasting southcoasting is offline
Senior Member
 
Join Date: Nov 2011
Location: Fairhaven, MA
Posts: 141
Thanks: 15
Thanked 22 Times in 13 Posts
Posted pic of dipstick
Attached Images
 
__________________
1971 Tartan 34C Sloop "NOVA LUNA", Rebuilt (2019) Fresh Water Cooled A4 (Bought boat in 2014)
1968 Tartan 27 Yawl "Destinada", rebuilt Old Lyme freshwater A4 (Sold boat in 2014)
Reply With Quote
  #9   IP: 155.186.124.219
Old 08-12-2020, 12:58 PM
Dave Neptune Dave Neptune is online now
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Grove, Oklahoma
Posts: 5,035
Thanks: 711
Thanked 1,289 Times in 839 Posts
Thumbs up

First do a compression check!! f the compression is good it will be time to pressure check the manifold. The manifold is easy to check as all you need to do is plug one end of the water jacket and pressurize the other. Those points are where the coolant goes in and out of the manifold.

There are many links as to how to set up the manifold test with a "schrader valve", pressure gage and a bicycle pump.

Once the results of BOTH tests are negative then time to test the block.

Dave Neptune
Reply With Quote
The Following User Says Thank You to Dave Neptune For This Useful Post:
TimBSmith (09-11-2020)
  #10   IP: 174.255.69.70
Old 08-12-2020, 01:02 PM
southcoasting's Avatar
southcoasting southcoasting is offline
Senior Member
 
Join Date: Nov 2011
Location: Fairhaven, MA
Posts: 141
Thanks: 15
Thanked 22 Times in 13 Posts
Quote:
Originally Posted by Dave Neptune View Post
First do a compression check!! f the compression is good it will be time to pressure check the manifold. The manifold is easy to check as all you need to do is plug one end of the water jacket and pressurize the other. Those points are where the coolant goes in and out of the manifold.

There are many links as to how to set up the manifold test with a "schrader valve", pressure gage and a bicycle pump.

Once the results of BOTH tests are negative then time to test the block.

Dave Neptune
Ok, but do I still need to if the manifold holds no pressure and I could hear air escaping back into exhaust?
__________________
1971 Tartan 34C Sloop "NOVA LUNA", Rebuilt (2019) Fresh Water Cooled A4 (Bought boat in 2014)
1968 Tartan 27 Yawl "Destinada", rebuilt Old Lyme freshwater A4 (Sold boat in 2014)
Reply With Quote
  #11   IP: 155.186.124.219
Old 08-12-2020, 01:52 PM
Dave Neptune Dave Neptune is online now
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Grove, Oklahoma
Posts: 5,035
Thanks: 711
Thanked 1,289 Times in 839 Posts
With the amount of coolant you are losing I doubt it's the manifold as that liquid would have to get past the rings to get into the oil. I think the compression check will yield your problem due to the amount of loss.

The water passage is sealed inside the manifold and only gets in & out via the two fittings on the top.

Save time do a compression check first.

Dave Neptune
Reply With Quote
  #12   IP: 137.103.82.227
Old 08-12-2020, 03:32 PM
joe_db's Avatar
joe_db joe_db is online now
Afourian MVP
 
Join Date: May 2009
Posts: 4,474
Thanks: 49
Thanked 1,026 Times in 721 Posts
WARNING - oil floats on water.
At first startup you are trying to lubricate the engine with pure water. After it runs a bit, you are trying to lubricate with oatmeal mush. Neither one works well.
Reply With Quote
  #13   IP: 174.255.68.4
Old 08-12-2020, 05:25 PM
southcoasting's Avatar
southcoasting southcoasting is offline
Senior Member
 
Join Date: Nov 2011
Location: Fairhaven, MA
Posts: 141
Thanks: 15
Thanked 22 Times in 13 Posts
Running compression test now...tons of water shooting up through plug holes...around 80 psi on all 4...cold engine
Attached Images
  
__________________
1971 Tartan 34C Sloop "NOVA LUNA", Rebuilt (2019) Fresh Water Cooled A4 (Bought boat in 2014)
1968 Tartan 27 Yawl "Destinada", rebuilt Old Lyme freshwater A4 (Sold boat in 2014)
Reply With Quote
  #14   IP: 174.255.68.4
Old 08-12-2020, 05:43 PM
southcoasting's Avatar
southcoasting southcoasting is offline
Senior Member
 
Join Date: Nov 2011
Location: Fairhaven, MA
Posts: 141
Thanks: 15
Thanked 22 Times in 13 Posts
After replacing oring on pressure gauge, I got closer to 85-90 psi on 3 cylinders and 65 on cylinder 3
Attached Images
 
__________________
1971 Tartan 34C Sloop "NOVA LUNA", Rebuilt (2019) Fresh Water Cooled A4 (Bought boat in 2014)
1968 Tartan 27 Yawl "Destinada", rebuilt Old Lyme freshwater A4 (Sold boat in 2014)
Reply With Quote
  #15   IP: 155.186.124.219
Old 08-12-2020, 05:53 PM
Dave Neptune Dave Neptune is online now
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Grove, Oklahoma
Posts: 5,035
Thanks: 711
Thanked 1,289 Times in 839 Posts
Did more moisture come out of #3?

Dave Neptune
Reply With Quote
  #16   IP: 174.255.68.4
Old 08-12-2020, 05:59 PM
southcoasting's Avatar
southcoasting southcoasting is offline
Senior Member
 
Join Date: Nov 2011
Location: Fairhaven, MA
Posts: 141
Thanks: 15
Thanked 22 Times in 13 Posts
Quote:
Originally Posted by Dave Neptune View Post
Did more moisture come out of #3?

Dave Neptune
There was so much on all that I really could not tell...
__________________
1971 Tartan 34C Sloop "NOVA LUNA", Rebuilt (2019) Fresh Water Cooled A4 (Bought boat in 2014)
1968 Tartan 27 Yawl "Destinada", rebuilt Old Lyme freshwater A4 (Sold boat in 2014)
Reply With Quote
  #17   IP: 155.186.124.219
Old 08-12-2020, 06:08 PM
Dave Neptune Dave Neptune is online now
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Grove, Oklahoma
Posts: 5,035
Thanks: 711
Thanked 1,289 Times in 839 Posts
Southcoasting, I "see" you have the water line into the manifold cut off. If you can just plug one end and blow into the other it should hold against you, if the pressure goes away quickly IE you have to keep blowing ~~ BINGO. This is not a good test but with the amount of liquid you are loosing the oral test might be fine. As a practice whenever I go to pressure check anything I do the same either by blowing or sucking. In many cases I did not have to hook up the gauge and stuff as the leak was obvious.

At 25lbs low it could well be the gasket but I would expect it to be lower.

Dave Neptune
Reply With Quote
The Following User Says Thank You to Dave Neptune For This Useful Post:
TimBSmith (09-11-2020)
  #18   IP: 137.103.82.227
Old 08-12-2020, 06:23 PM
joe_db's Avatar
joe_db joe_db is online now
Afourian MVP
 
Join Date: May 2009
Posts: 4,474
Thanks: 49
Thanked 1,026 Times in 721 Posts
Seeing as this is a fresh overhaul, is there a plug or something somewhere someone forgot to put back
Reply With Quote
  #19   IP: 174.255.68.4
Old 08-12-2020, 06:33 PM
southcoasting's Avatar
southcoasting southcoasting is offline
Senior Member
 
Join Date: Nov 2011
Location: Fairhaven, MA
Posts: 141
Thanks: 15
Thanked 22 Times in 13 Posts
Quote:
Originally Posted by joe_db View Post
Seeing as this is a fresh overhaul, is there a plug or something somewhere someone forgot to put back
I don’t know but I read about the plug on the valve side on one of the bulletins...the main thing to note though it that the leak at the manifold is significant...as soon as I pump my tire inflator I could hear a good amount of hissing shooting out in manifold. It does not hold any kind of pressure not ever for a millisecond
__________________
1971 Tartan 34C Sloop "NOVA LUNA", Rebuilt (2019) Fresh Water Cooled A4 (Bought boat in 2014)
1968 Tartan 27 Yawl "Destinada", rebuilt Old Lyme freshwater A4 (Sold boat in 2014)
Reply With Quote
  #20   IP: 174.255.68.4
Old 08-12-2020, 06:36 PM
southcoasting's Avatar
southcoasting southcoasting is offline
Senior Member
 
Join Date: Nov 2011
Location: Fairhaven, MA
Posts: 141
Thanks: 15
Thanked 22 Times in 13 Posts
Quote:
Originally Posted by Dave Neptune View Post
Southcoasting, I "see" you have the water line into the manifold cut off. If you can just plug one end and blow into the other it should hold against you, if the pressure goes away quickly IE you have to keep blowing ~~ BINGO. This is not a good test but with the amount of liquid you are loosing the oral test might be fine. As a practice whenever I go to pressure check anything I do the same either by blowing or sucking. In many cases I did not have to hook up the gauge and stuff as the leak was obvious.

At 25lbs low it could well be the gasket but I would expect it to be lower.

Dave Neptune
Yes, I had already indicated in previous posts that the manifold has a big hole somewhere and that is the culprit. I plugged it so that I can blow air in the other end via a tire inflator...holds no pressure at all and I could hear air/water gurgling into exhaust...I will be replacing it in the next few days...
__________________
1971 Tartan 34C Sloop "NOVA LUNA", Rebuilt (2019) Fresh Water Cooled A4 (Bought boat in 2014)
1968 Tartan 27 Yawl "Destinada", rebuilt Old Lyme freshwater A4 (Sold boat in 2014)
Reply With Quote
  #21   IP: 155.186.124.219
Old 08-12-2020, 07:14 PM
Dave Neptune Dave Neptune is online now
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Grove, Oklahoma
Posts: 5,035
Thanks: 711
Thanked 1,289 Times in 839 Posts
Then the manifold is the culprit for the gobs of water.

Important, get the coolant sucked out of the engine and be ready to flush the oil a couple of times once you get the new manifold on. Be careful removing the exhaust, old exhaust systems that have a year or 2 left can easily snap off with not much effort.

If you "hydrauliced" the engine you still may have a small breech in the head-gasket thus the low #3. Had you done a compression check any time before this incident? If so was #3 low?

Dave Neptune
Reply With Quote
The Following User Says Thank You to Dave Neptune For This Useful Post:
southcoasting (08-12-2020)
  #22   IP: 155.186.124.219
Old 08-12-2020, 07:17 PM
Dave Neptune Dave Neptune is online now
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Grove, Oklahoma
Posts: 5,035
Thanks: 711
Thanked 1,289 Times in 839 Posts
Sorry, I missed part of your #7 post. Been a busy day.

Best

Dave Neptune
Reply With Quote
  #23   IP: 137.103.82.227
Old 08-12-2020, 07:57 PM
joe_db's Avatar
joe_db joe_db is online now
Afourian MVP
 
Join Date: May 2009
Posts: 4,474
Thanks: 49
Thanked 1,026 Times in 721 Posts
That is good news, a new manifold and problem solved
Reply With Quote
  #24   IP: 73.234.59.26
Old 08-12-2020, 10:34 PM
southcoasting's Avatar
southcoasting southcoasting is offline
Senior Member
 
Join Date: Nov 2011
Location: Fairhaven, MA
Posts: 141
Thanks: 15
Thanked 22 Times in 13 Posts
Quote:
Originally Posted by Dave Neptune View Post
Then the manifold is the culprit for the gobs of water.

Important, get the coolant sucked out of the engine and be ready to flush the oil a couple of times once you get the new manifold on. Be careful removing the exhaust, old exhaust systems that have a year or 2 left can easily snap off with not much effort.

If you "hydrauliced" the engine you still may have a small breech in the head-gasket thus the low #3. Had you done a compression check any time before this incident? If so was #3 low?

Dave Neptune
I had not run a compression test but I know I had a couple valves that were stuck...it could be a stuck valve?
__________________
1971 Tartan 34C Sloop "NOVA LUNA", Rebuilt (2019) Fresh Water Cooled A4 (Bought boat in 2014)
1968 Tartan 27 Yawl "Destinada", rebuilt Old Lyme freshwater A4 (Sold boat in 2014)
Reply With Quote
  #25   IP: 73.234.59.26
Old 09-11-2020, 08:15 AM
southcoasting's Avatar
southcoasting southcoasting is offline
Senior Member
 
Join Date: Nov 2011
Location: Fairhaven, MA
Posts: 141
Thanks: 15
Thanked 22 Times in 13 Posts
Just wanted to update on this...I had a spare manifold from my old engine which I had sandblasted and painted it...pressure was good on this one...

After about 9 hours or runtime most of which was a 5 day cruise to Martha’s Vineyard and Nantucket, all is good! There is an unusual amount of heat buildup on the aft end of manifold but maybe it’s normal...I will post something on this...all is good on this main issue though!
__________________
1971 Tartan 34C Sloop "NOVA LUNA", Rebuilt (2019) Fresh Water Cooled A4 (Bought boat in 2014)
1968 Tartan 27 Yawl "Destinada", rebuilt Old Lyme freshwater A4 (Sold boat in 2014)
Reply With Quote
The Following 2 Users Say Thank You to southcoasting For This Useful Post:
Surcouf (09-11-2020), TimBSmith (09-11-2020)
Reply

Tags
fresh water cooling, fwc, overheating, rebuild

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Controlling and affecting proper operating temp ILikeRust Troubleshooting 88 02-02-2016 01:36 PM
coolant loss wsulli For Sale - Other Items 4 01-06-2014 03:47 PM
Sporadic coolant loss jhwelch Cooling System 11 11-24-2011 04:28 AM
Gradual Loss of Power, Overheating forcenine Fuel System 5 03-03-2008 09:00 PM
Overheating problems jdaly986 Cooling System 1 01-16-2008 10:32 AM


All times are GMT -4. The time now is 04:47 PM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2024 Moyer Marine Inc.

All Rights Reserved