Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Discussion Topics > Troubleshooting

Reply
 
Thread Tools Display Modes
  #1   IP: 69.158.71.200
Old 08-24-2019, 08:05 PM
splashlog splashlog is offline
Senior Member
 
Join Date: Aug 2019
Posts: 56
Thanks: 22
Thanked 3 Times in 3 Posts
Electronic Igition Test

Had spark off the ignition coil with really old points/condenser but no spark at plugs.
Removed points and condenser (prestolite/autolite), replaced with EI pertronix, nothing.
Had to remove distro to do the change over, marked rotor position, replaced rotor and cap with new.
Checked coil voltage OK, coil ohms Ok.
No spark anywhere now
What did I miss?
Did I mess up timing? Is there a way to check if EI is OK?
Bueller?
Reply With Quote
  #2   IP: 70.186.108.69
Old 08-24-2019, 10:40 PM
CajunSpike's Avatar
CajunSpike CajunSpike is offline
Senior Member
 
Join Date: Jan 2018
Location: New Orleans, LA
Posts: 240
Thanks: 222
Thanked 41 Times in 31 Posts
Not to long ago, I installed EI into my late model A4. Pulled points/plate and installed EI plate. Installed ring around the shaft..put it back together. Cranked, got nothing.
Pulled cap off again and figured out I hadn't put the ring low enough on the shaft. Due to my error, the rotor was not being fully seated. The shaft had stripped the rotor positioning slot and the rotor was not turning.

Tapped the sensor ring lower on the shaft, fully seated the rotor(later replaced), reassembled cap.
Checked spark, and got it. Engine started shortly after.
__________________
Bill L.
1972 Ericson 27
Hull #61
Atomic 4
Reply With Quote
The Following User Says Thank You to CajunSpike For This Useful Post:
splashlog (08-24-2019)
  #3   IP: 24.152.132.140
Old 08-24-2019, 10:47 PM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
Rotor-distributor cap problem.
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others
Reply With Quote
The Following User Says Thank You to ndutton For This Useful Post:
splashlog (08-24-2019)
  #4   IP: 216.145.121.132
Old 08-25-2019, 11:28 AM
roadnsky's Avatar
roadnsky roadnsky is offline
Afourian MVP
 
Join Date: Dec 2008
Location: Lake Mead, NV
Posts: 3,104
Thanks: 24
Thanked 467 Times in 309 Posts
One other thought; and I'm not trying to offend by pointing out basics.

Since the new EI has TWO wires...
Are they connected correctly?
__________________
-Jerry

'Lone Ranger'

1978 RANGER 30
Reply With Quote
  #5   IP: 69.158.71.200
Old 08-25-2019, 06:07 PM
splashlog splashlog is offline
Senior Member
 
Join Date: Aug 2019
Posts: 56
Thanks: 22
Thanked 3 Times in 3 Posts
Trust me, I grieved over making sure I had the wiring all sorted out. If people could just stick to standard wire codes the world would be a much better place...

Anyway, still no fun/spark. I rechecked the installation, as I was concerned that the physical install may not have been correct, but it is. I looked at the rotor and cap and no damage, there is .25" from the top of the cam shaft to the top of the encoder ring as specified.

I am going on the notion that even if the timing is off, I would at least still get a spark off the HT coil cable IF the EI, Coil and Power are good while starting. Could it be a bad ground? I cleaned up the Distro when I removed it and sanded near where the old point connection was, should I try taking the ground to somewhere else?

I am wondering if it's possible that even with 12+V at the coil that when the iginition is on that for whatever reason the circiut is not getting enough current? Would running a jumper direct from the battery (+) to the coil be a good idea to test?

I do have a brand new coil, but it's 1.5 ohm and I have a ballast resistor to go with it, but I am trying to keep the troubleshooting as simple as possible.

Thoughts?
Reply With Quote
The Following User Says Thank You to splashlog For This Useful Post:
tenders (08-27-2019)
  #6   IP: 70.185.132.167
Old 08-26-2019, 01:01 AM
JOHN COOKSON JOHN COOKSON is offline
Afourian MVP, Professor Emeritus
 
Join Date: Nov 2008
Posts: 3,500
Thanks: 54
Thanked 855 Times in 629 Posts
Has the cooling water inlet valve been closed while you have been no start cranking?

TRUE GRIT
Reply With Quote
  #7   IP: 71.38.107.125
Old 08-26-2019, 09:24 AM
roadnsky's Avatar
roadnsky roadnsky is offline
Afourian MVP
 
Join Date: Dec 2008
Location: Lake Mead, NV
Posts: 3,104
Thanks: 24
Thanked 467 Times in 309 Posts
Take a look at the attached procedure.
Might be worth a try.
Attached Images
File Type: pdf Ignitor Module Check.pdf (278.0 KB, 926 views)
__________________
-Jerry

'Lone Ranger'

1978 RANGER 30
Reply With Quote
The Following User Says Thank You to roadnsky For This Useful Post:
splashlog (08-26-2019)
  #8   IP: 69.158.71.200
Old 08-28-2019, 11:06 AM
splashlog splashlog is offline
Senior Member
 
Join Date: Aug 2019
Posts: 56
Thanks: 22
Thanked 3 Times in 3 Posts
@John. How would the water intake O/C affect ignition? It was closed.
Reply With Quote
  #9   IP: 108.34.253.10
Old 08-28-2019, 12:01 PM
jcwright jcwright is offline
Afourian MVP
 
Join Date: Jul 2012
Posts: 158
Thanks: 5
Thanked 99 Times in 75 Posts
Hello Splashlog.

The suggestion about closing the water intake is that, with certain types of exhaust systems, excessive cranking without starting can lead to water back-siphoning into the engine.

You can find a detailed discussion of this in the thread linked below; see especially the diagram by Neil at entry #3 (I believe):

http://www.moyermarineforum.com/foru...ad.php?t=10787

Best regards,

jack
Reply With Quote
  #10   IP: 69.158.71.200
Old 08-28-2019, 06:09 PM
splashlog splashlog is offline
Senior Member
 
Join Date: Aug 2019
Posts: 56
Thanks: 22
Thanked 3 Times in 3 Posts
I don't think that is a factor in this case. I never crank more than 5 seconds at a time and I let things cool between cycles ( I am predicting the next failure will be the starter and or alternator, which I plan to remove and clean/rebuild over the layup this winter). I did a check for water in the oil and it's all good.

Saturday is my next chance to get a spark. I will run a jumper direct from the battery to the coil as well, try to verify the EI is good.
Reply With Quote
  #11   IP: 70.185.132.167
Old 08-28-2019, 07:44 PM
JOHN COOKSON JOHN COOKSON is offline
Afourian MVP, Professor Emeritus
 
Join Date: Nov 2008
Posts: 3,500
Thanks: 54
Thanked 855 Times in 629 Posts
Just To Be Sure

Take a voltage reading at coil + while cranking.

TRUE GRIT
Reply With Quote
  #12   IP: 24.152.132.140
Old 08-28-2019, 07:49 PM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
Multiple issues

In post #1 you reported good spark out of the coil with points but nothing out of the spark plug leads. The rotor is supposed to receive the coil spark on its center tab from the distributor cap center post and deliver it to one of four contacts at the distributor cap perimeter. Either the rotor center tab was not making contact with the center post or all four perimeter contacts were not making contact with the rotor shoe. I suspect the former, solved by making certain the distributor cap is properly seated on the distributor body and if necessary, slightly bending the rotor tab up to be certain it makes contact.

Also in post #1 you report no spark out of the coil after the switch to electronic ignition. The possibilities are no input voltage to the coil '+' post or the magnetic ring is not in proper proximity to the EI module - - or both. At this point it doesn't much matter because even if you had spark out of the coil it doesn't make it to the plugs.

If it were me, I'd revert back to the old points to regain coil spark and resolve the rotor-distributor cap interface issue. Once that is done and successful, proceed to electronic ignition.

Quote:
I never crank more than 5 seconds at a time and I let things cool between cycles
Water volume in the muffler is cumulative and letting it cool does not remove the water within. Without exhaust pressure of a running engine the muffler will continue to fill even at 5 second intervals. 12 cycles of 5 second no-start efforts equals a 60 second no-start period in terms of water volume.
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others

Last edited by ndutton; 08-28-2019 at 07:55 PM.
Reply With Quote
  #13   IP: 69.158.71.200
Old 08-30-2019, 09:01 PM
splashlog splashlog is offline
Senior Member
 
Join Date: Aug 2019
Posts: 56
Thanks: 22
Thanked 3 Times in 3 Posts
I agree reverting to points is a sensible next move, my concern however is that it will force me to remove the distro again, which means there is a good chance now that I will have screwed up the timing. Is this a lgititimate concern?
Reply With Quote
  #14   IP: 24.152.132.140
Old 08-30-2019, 09:22 PM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
If the timing is already suspected to be off, removing the distributor again won't make any difference. When it is replaced a start from scratch timing exercise will have to be done. Read up on the forum for a lot of detailed information on how to do it properly including a very cool balloon tool for finding Top Dead Center.

http://www.moyermarineforum.com/foru...06&postcount=1
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others

Last edited by ndutton; 08-31-2019 at 10:10 AM.
Reply With Quote
  #15   IP: 69.158.71.200
Old 09-04-2019, 12:20 AM
splashlog splashlog is offline
Senior Member
 
Join Date: Aug 2019
Posts: 56
Thanks: 22
Thanked 3 Times in 3 Posts
simple coil test

TIL that the original coil is good.
Coil test; get 12v+ to coil from good power source (I used an old utility power supply, but a decently charged 12v battery would be just as good). Make a wire that fits into the output (CT/HT), I did this to bypass the usual distro wire. Make - (on coil) to GND but make it temporary, clip, bare end wire, etc. With power on, you will see a small spark as you contact the (-) to the coil. This is good. Now take your (CT/HT) wire and place a bare end close to the (-) terminal of the coil. Now interupt the (-) wire at the coil and look for fire. Just use one hand to break the (-) on and off the terminal (you are now a human Distro) and use the other hand to hold the CT/HT close to the (-) (GND) terminal. If power is good and coil is good you will see the spark and hopefully as well, the light...

Doing it this way bypasses all existing boat wiring, I got a nice blue light show that jumped a good 3/4". Coil is not the problem..

So, in my case, I will have to now look at the wiring from the battery to the ignition switch and back to the coil. I was not getting any spark at all even though my meter was indicating proper voltage.

I hope this makes sense.
Reply With Quote
  #16   IP: 24.152.132.140
Old 09-04-2019, 12:45 AM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
The (-) coil terminal is NOT a ground. You secondary lead spark test should have been to the block or head.
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others
Reply With Quote
  #17   IP: 69.158.71.200
Old 09-04-2019, 10:08 PM
splashlog splashlog is offline
Senior Member
 
Join Date: Aug 2019
Posts: 56
Thanks: 22
Thanked 3 Times in 3 Posts
Quote:
Originally Posted by ndutton View Post
The (-) coil terminal is NOT a ground. You secondary lead spark test should have been to the block or head.
Sure, however doing that was impossible as I did this test in the comfort of my shop bench. In my set up, the coil (-) terminates on the Distro via a screw that would have held the condenser in place. A meter check verifies that this point on the distro is GND/(-). Either way, my test proves that the coil is OK.

I was also able to verify that the EI is good by powering up the IGN power and metering the Vdrop while I truned the motor over.

Really all that there is left to try is; A) jumping new wire from the BATT/IGN switch to coil, (bypass the switch) and B) Changing out the IGN coil wire (Secondary)

I should have this wrapped up by Haulout..
Reply With Quote
Reply

Tags
Bueller, coil, electronic ignition test, no spark, timing

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Spark Test ndutton Testing Protocols 10 10-02-2019 01:13 AM
Test pressures ndutton Cooling System 8 08-25-2013 09:05 PM
Coil troubleshooting with a test light? JonnyQuest Ignition System 2 05-04-2013 09:33 AM
Any other way to test for secondary discharge with electronic ignition Baltimore Sailor Ignition System 3 04-15-2008 09:54 AM
Compression test baileyem General Maintenance 2 06-18-2007 03:16 PM


All times are GMT -4. The time now is 08:48 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2024 Moyer Marine Inc.

All Rights Reserved