Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Discussion Topics > Reversing Gear

Reply
 
Thread Tools Display Modes
  #1   IP: 176.22.251.50
Old 07-19-2020, 08:14 AM
ChristianBF ChristianBF is offline
Member
 
Join Date: Jul 2020
Posts: 4
Thanks: 0
Thanked 3 Times in 2 Posts
Reverse Gear selector jumps out of gearselector?

Hello all, hello from Haderslev, Denmark, where we run an Atomic engine from 1979. In a sailboat bought and custom build by my great-granddad in 1935.

please see the two pictures in the post or the imgur link, this little “tap” for pulling the reverse gear lever jumps out of the hole again and again. We have tried to move the “gear selector” below, over to the right side, and fix it, but it does not help,
we have also tightened the revers nut but without luck, it continues to jump out. any advice out there?

kind regards Christian Fuglsang from denmark

https://imgur.com/a/oMjen99

PS i have noticed the pictures are being turned 90 deg counter clock wise by the forum. For correct orientation please use the Imgur link
Attached Images
   
Reply With Quote
  #2   IP: 32.211.28.40
Old 07-19-2020, 03:53 PM
Al Schober's Avatar
Al Schober Al Schober is offline
Afourian MVP
 
Join Date: Jul 2009
Location: Uncasville, CT
Posts: 1,779
Thanks: 11
Thanked 377 Times in 281 Posts
The cross shaft for adjusting reverse has been modified. Usual install has a pin (swaged in place) that hold a roller. On yours I see a hex head. I suspect the adjustment was made too tight, the pin sheared, and the roller fell into the sump. Repair was not properly done.
I also suspect if you look at the piece the actuating cam bears against, you'll find it is heavily worn.
Reply With Quote
  #3   IP: 32.211.28.40
Old 07-20-2020, 12:26 PM
Al Schober's Avatar
Al Schober Al Schober is offline
Afourian MVP
 
Join Date: Jul 2009
Location: Uncasville, CT
Posts: 1,779
Thanks: 11
Thanked 377 Times in 281 Posts
Here are a few more photos that may help.
First shows an assembled view with labels. With the adjusting nut removed, the adjusting rod can be slid to the right, allowing removal of the actuating bar.
The next photo shows the end of the adjusting rod with the roller in the slot. At this point, you can use your finger to feel if there is a groove worn into the side of the brace.
In the next photo the adjusting rod has been removed and you can see the cross pin in the adjusting rod. This pin is about 6mm diameter. The roller measures 12.4mm.
Attached Images
   
Reply With Quote
The Following User Says Thank You to Al Schober For This Useful Post:
ronstory (01-22-2021)
  #4   IP: 176.22.251.50
Old 07-21-2020, 05:06 AM
ChristianBF ChristianBF is offline
Member
 
Join Date: Jul 2020
Posts: 4
Thanks: 0
Thanked 3 Times in 2 Posts
Thanks, for Measurements.

Quote:
Originally Posted by Al Schober View Post
The cross shaft for adjusting reverse has been modified. Usual install has a pin (swaged in place) that hold a roller. On yours I see a hex head. I suspect the adjustment was made too tight, the pin sheared, and the roller fell into the sump. Repair was not properly done.
I also suspect if you look at the piece the actuating cam bears against, you'll find it is heavily worn.
Your knowledge has led to great ideas, the 12.4mm is an interesting number which we could not find in the instruction manual, the bolt is an M7 (7mm), I will get our factory smith to make a new roller on the Lathe today. This will hopefully help, this is at least a start to a solution.

My dad has also noticed that the "brace" as you call it has a hole in it, is this for fastening the brace? because the brace has also become loose, the whole Clutch mechanism can then move freely up and down on the planetary gear assembly, which is very concerning.

but this is probably a problem connected to the missing roller sins everything is a bit more lose the intended.

I will write again regarding this when the new roller has been fitted.

Thanks again from Denmark.
Reply With Quote
  #5   IP: 32.211.28.40
Old 07-21-2020, 11:06 AM
Al Schober's Avatar
Al Schober Al Schober is offline
Afourian MVP
 
Join Date: Jul 2009
Location: Uncasville, CT
Posts: 1,779
Thanks: 11
Thanked 377 Times in 281 Posts
Fitting a roller to the M7 bolt seems like a reasonable way to go.
The brace is meant to hold the planetary brake band in a fixed fore/aft position. The aft end of a brace has a large hole in it and goes around the shifter cross shaft. The fwd end of the brace has a smaller hole that fits over a pin in the brake band.
Removing the brace requires removing the transmission cover. Same for the cross shaft unless the cover is modified to provide a hole - photo shows mine with the hole.
I checked into Haderslev, and find I was quite near there about 20 months ago. We were visiting relatives - spent some time on Bornholm, a couple of days in Copenhagen, stop in Middelfart, up to Ry for two days, a visit to Ribe, and finally a visit to Flensburg (used to be Danish). Had a good time!
Attached Images
 
Reply With Quote
The Following User Says Thank You to Al Schober For This Useful Post:
sastanley (08-11-2020)
  #6   IP: 147.78.29.28
Old 08-07-2020, 09:12 AM
ChristianBF ChristianBF is offline
Member
 
Join Date: Jul 2020
Posts: 4
Thanks: 0
Thanked 3 Times in 2 Posts
Quote:
Originally Posted by Al Schober View Post
Fitting a roller to the M7 bolt seems like a reasonable way to go.
The brace is meant to hold the planetary brake band in a fixed fore/aft position. The aft end of a brace has a large hole in it and goes around the shifter cross shaft. The fwd end of the brace has a smaller hole that fits over a pin in the brake band.
Removing the brace requires removing the transmission cover. Same for the cross shaft unless the cover is modified to provide a hole - photo shows mine with the hole.
I checked into Haderslev, and find I was quite near there about 20 months ago. We were visiting relatives - spent some time on Bornholm, a couple of days in Copenhagen, stop in Middelfart, up to Ry for two days, a visit to Ribe, and finally a visit to Flensburg (used to be Danish). Had a good time!
So we installed the new roller a couple of weeks ago, and until now it seems to have fixed the problem, but we will make a better-fitted roller in the winter as a more longterm fix.

again thanks for the help
Reply With Quote
The Following User Says Thank You to ChristianBF For This Useful Post:
sastanley (08-11-2020)
  #7   IP: 176.22.251.50
Old 01-22-2021, 07:17 AM
ChristianBF ChristianBF is offline
Member
 
Join Date: Jul 2020
Posts: 4
Thanks: 0
Thanked 3 Times in 2 Posts
The long term repair has been made!

Hello again, after some time.
We have now done the long term repair has been hade. As you can see on the picture a new roller has been made, and a new bolt.

Special thanks to [QUOTE=Al Schober;122101] for helping us to get the right measurement on some of the components.

When covid is over and you are in Denmark feel free to contact us if you want to know anything.
christian@fuglsang.dk

Best regards.
The whole Fuglsang Family.
Attached Images
  
Reply With Quote
The Following 2 Users Say Thank You to ChristianBF For This Useful Post:
Surcouf (01-22-2021), TimBSmith (01-29-2021)
  #8   IP: 32.211.28.40
Old 01-26-2021, 10:08 PM
Al Schober's Avatar
Al Schober Al Schober is offline
Afourian MVP
 
Join Date: Jul 2009
Location: Uncasville, CT
Posts: 1,779
Thanks: 11
Thanked 377 Times in 281 Posts
Glad your reversing gear is working again, and glad to have been of assistance. That's what this forum is about - people helping each other.
Reply With Quote
  #9   IP: 69.250.111.245
Old 01-27-2021, 11:57 AM
sastanley's Avatar
sastanley sastanley is online now
Afourian MVP
 
Join Date: Sep 2008
Location: Solomons, MD
Posts: 6,788
Thanks: 800
Thanked 441 Times in 333 Posts
Thumbs up

Al, I don't know how I missed your detailed and labeled pictures earlier in this thread from 2020, but a couple minutes studying it clears up (for me anyway) some of the mysteries of the reversing gear.

Learn something new every day!

Thanks again!

Also, thanks to Christian for following up. A few years from now, someone will see your fix and have a path to repair!!
__________________
-Shawn
"Twice Around" - '77 Catalina 30, #511 with original A-4 & MMI manifold.
She is even happier with fresh paint on the topsides!

http://www.moyermarine.com/forums/signaturepics/sigpic3231_6.gif

Last edited by sastanley; 01-27-2021 at 12:02 PM.
Reply With Quote
The Following User Says Thank You to sastanley For This Useful Post:
TimBSmith (01-29-2021)
Reply

Tags
gear box, problem, reverse gear

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Forward and Reverse Gear Adjustment Issues CraigRun Reversing Gear 12 05-17-2012 09:15 PM
Reverse gear overheat?? NorfolkRagbagger Reversing Gear 5 10-13-2010 09:20 AM
early model reverse gear removal sun Reversing Gear 2 07-12-2009 06:18 PM
How far to adjust the adjusting nut on the reverse gear? dsimon1044 Reversing Gear 4 03-10-2009 02:37 AM


All times are GMT -4. The time now is 10:15 PM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2021, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2021 Moyer Marine Inc.

All Rights Reserved