#26
IP: 100.36.65.17
|
||||
|
||||
I think the apparent elongation of the mounting holes is just a photographic issue (pincushion distortion) caused by a wide-angle lens.
__________________
@(^.^)@ Ed 1977 Pearson P-323 "Dolce Vita" with rebuilt Atomic-4 |
The Following User Says Thank You to edwardc For This Useful Post: | ||
CRUX (02-24-2021) |
#27
IP: 134.41.100.227
|
||||
|
||||
Not a terrible looking pan. Suggest sanding and grinding that pitting etc off there, clean with reducer, and paint with the best paint you can afford right now. 2 part epoxy would be my choice, but I have that laying around. I understand going out and buying it costs more than the pan...unless you know someone that uses the stuff and can do it for you on the side. (you wouldn't believe how much stuff I get done like that...favor for favor).
You are doing the right thing there. Not a bad looking pan.
__________________
Mo "Odyssey" 1976 C&C 30 MKI The pessimist complains about the wind. The optimist expects it to change. The realist adjusts the sails. ...Sir William Arthur Ward. |
The Following User Says Thank You to Mo For This Useful Post: | ||
CRUX (02-24-2021) |
#28
IP: 72.10.126.197
|
|||
|
|||
Un-related to the oil pan, I have some deep scaling on the on all sides of the water jacket side plate. So deep that I am definitely wary to start chipping away. The pictures don't do it justice.
I find this odd because there have been NO indications of a leak in that area since I've owned the boat for the past couple seasons. The side plate/bolts don't look original to me, though i could be mistaken. One bolt head is gone completely, while the all the others look good. FYI I run with the bypass loop and NO thermostat at about 110-120 degrees consistently, so no issues of overheating. I imagine I will have have to swap out every bolt for studs, etc if I were to try to open up the side jacket, but I REALLY don't want to go down that road right now. Launch day is coming up quick and I'm only halfway done with the oil pan swap. Is it a terrible idea to leave as is?? |
The Following User Says Thank You to CRUX For This Useful Post: | ||
TimBSmith (04-16-2021) |
#29
IP: 134.134.137.84
|
||||
|
||||
My two cents... if you are this close to plate that is missing a bolt head, I would fix it. It's going to be a lot easier to get access to that area now.
If your motor has decent compression, oil pressure and limited blow-by... there is no reason you could not get years out of this re-install. However, if it starts to leak later... trying to get rusted side plate off in situ is not going to be fun. IMO, those side plate bolt make that pan and head bolts look easy. I broke two off even with soaking, tapping and heat. Well, at least there is one bolt that won't break off on you... so only 7 to go.
__________________
Thanks, Ron Portland, OR Last edited by ronstory; 03-02-2021 at 12:03 AM. Reason: typo, still typos |
#30
IP: 165.225.20.149
|
||||
|
||||
I had a very scaled motor, exactly where your is... This part went OK. A lot of "cold chiseling" and scrapping , then multiple cleaning and then POR painting.
But scaling only occurrs with water, so you must have one small leak potentially only when engine is hot. Be aware that the A4 head casting has a weak point below the water pump, just above your heavy scaling...
__________________
Surcouf A nostalgic PO - Previously "Almost There" - Catalina 27 (1979) |
#31
IP: 69.116.139.83
|
|||
|
|||
Making progress. Old pan is off. Only one broken bolt, hoping to be able to turn it out with some vice grips.
Sourced my "new" pan, prepping for painting now. Doing this job in the cabin, glad to have so much room in the C30 |
#32
IP: 32.211.28.40
|
||||
|
||||
Photo #1 in post #28 is REAL ugly. Is that a freeze crack?
|
#33
IP: 98.155.50.7
|
||||
|
||||
The inners look like their as suppose to, that's good news. I would clean the oil screen since it just staring you down in it's current configuration. ;^)
It just spins off and don't lose the spring and washers. Get any large deposits off with a clean non-fuzzy rag and solvent and you can stick the long nozzle of wd-40 from the inside to help get the deposits off. If you want a gold star you can take off the twisted wire and remove the screen but they are fragile and if I could get it pretty clean with WD or an air nozzle from the inside, I would call it good enough. Keep going, you are "almost there". That last phrase exclusively was for Surcouf.
__________________
Thanks, Ron Portland, OR |
The Following User Says Thank You to ronstory For This Useful Post: | ||
CRUX (03-06-2021) |
#34
IP: 69.116.139.83
|
|||
|
|||
It was a thin slab of scaled
|
#35
IP: 69.116.139.83
|
|||
|
|||
Successfully finished the job yesterday and the engine is back installed! Running like a top. Splash date is May 8.
Very thankful for the amount of room in the C30's, couldn't imagine doing the pan swap in a smaller boat. Ended up replacing the carb, fuel pump, & water pump while I was at it. Thanks for everyone's advice along the way. |
#36
IP: 134.134.139.87
|
||||
|
||||
Thanks for following up the resolution. On some thread we get "no closure" which is like reading an exciting book, only to find out its missing the last chapter.
__________________
Thanks, Ron Portland, OR |
The Following User Says Thank You to ronstory For This Useful Post: | ||
CRUX (04-18-2021) |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Accessory drive?...Elusive water pump oil leak | Mo | Troubleshooting | 4 | 10-24-2020 09:17 PM |
Finding the source of a gas leak | Minnesota_Slick | Troubleshooting | 40 | 06-16-2014 01:34 PM |
Exhaust leak? | Ajax | Exhaust System | 19 | 11-25-2011 09:49 AM |
Head Leak from Alternator Bracket | kakers | Overhaul | 12 | 09-11-2011 07:31 AM |
Mystery water leak | tartansailboat | Cooling System | 20 | 09-07-2011 08:39 AM |