Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Discussion Topics > General Maintenance

Reply
 
Thread Tools Display Modes
  #26   IP: 72.69.36.126
Old 10-30-2020, 05:58 PM
tenders tenders is offline
Afourian MVP
 
Join Date: May 2007
Location: Harlem YC, City Island, NY
Posts: 1,391
Thanks: 37
Thanked 214 Times in 143 Posts
Quote:
Originally Posted by Peter View Post
PS - sort of like when I loaned my car to someone and half-way through explaining that the hockey stick through the hole in the floor is the brakes, I realized that maybe there IS something wrong with the car that should get fixed and that hockey stick brakes, while they were normal for me, are in fact not normal.
Wow, that is VERY Canadian.
Reply With Quote
The Following User Says Thank You to tenders For This Useful Post:
Peter (10-30-2020)
  #27   IP: 131.162.64.3
Old 10-30-2020, 08:49 PM
Peter's Avatar
Peter Peter is online now
Senior Member
 
Join Date: Jul 2016
Location: Nova Scotia, Canada
Posts: 253
Thanks: 97
Thanked 112 Times in 80 Posts
sorry...
Reply With Quote
  #28   IP: 69.172.163.17
Old 10-31-2020, 10:24 PM
cowlum cowlum is online now
Senior Member
 
Join Date: Aug 2020
Posts: 16
Thanks: 0
Thanked 7 Times in 4 Posts
Hi again

Today was sunny and we ended up going on a last minute cruise. I ran the engine for an hour, all running perfectly. My partner allowed me 20 minutes after to play with the engine while the kid slept.

So I decided to test some of my assumptions.

After running the engine for an hour on our cruise I poured a little antifreeze in cylinder 3 and a little engine oil in cylinder 4 after. The antifreeze did not boil as I had assumed, but it did not mix with the fluid on the surface of the piston. The oil mixed straight in.

This test lead me to believe the engine simple doesn't produce the heat to burn the motor oil. So I ran the engine at WOT for 30 seconds which produced the heat to brown the oil on the surface (i think).

Of interest, cylinder 3's spark plug and exhaust valve had been 'cleaned' by the antifreeze. cylinder 4's spark plug is still charcoal black.
I also tested antifreeze in C4 but dont have a good photo, it didnt mix same as cylinder 3.

I now think what I took a picture of in C4 a week ago was a piston cleaned by seafoam, which received the lions share due to gravitiy. Then covered in oil from the compression test.
That or it came in with the fuel with c4 getting the lions share due to gravity again.

My learning from these experiment is its not as hot inside the cylinder as I had originally assumed.
I also set up a antifreeze evaporation test.

Yes, Ill still be performing the pressure test sometime in the next month but thought maybe someone finds this as interesting as I do.
Attached Images
   

Last edited by cowlum; 10-31-2020 at 10:38 PM.
Reply With Quote
The Following User Says Thank You to cowlum For This Useful Post:
Surcouf (11-02-2020)
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Piston rod replacement / matching BryanLee Overhaul 13 03-07-2011 10:36 AM
Piston Oil Ring Damage Found - relacement ? Mike Jenkins Overhaul 4 12-09-2008 09:48 PM
Water in piston 4 Herman Boermans Troubleshooting 2 10-01-2007 04:26 PM
Water in piston 4 Herman Boermans Troubleshooting 0 09-27-2007 04:53 PM


All times are GMT -4. The time now is 04:53 PM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2020, vBulletin Solutions, Inc.


Universalģ is a registered trademark of Westerbeke Corporation

Copyright © 2004-2020 Moyer Marine Inc.

All Rights Reserved