Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Discussion Topics > Electrical

Reply
 
Thread Tools Display Modes
  #1   IP: 71.200.119.246
Old 03-31-2013, 01:14 PM
Hymodyne's Avatar
Hymodyne Hymodyne is offline
 
Join Date: Feb 2013
Location: Salisbury, MD
Posts: 376
Thanks: 53
Thanked 13 Times in 12 Posts
using a4 alt to charge house batteries

I currently have a small solar panel that maintians the charge on the twin marine batteries that I use for my house power. Is there a way, say, by wiring the house batteries to the Vreg from the engine, that I can use the alternator's charging power to recharge the other batteries? The solar panel has an external regulator, but I believe it would be quickly overloaded by the alternator.

James
Reply With Quote
  #2   IP: 24.74.200.178
Old 03-31-2013, 02:22 PM
Marian Claire's Avatar
Marian Claire Marian Claire is offline
Afourian MVP
 
Join Date: Aug 2007
Posts: 1,797
Thanks: 33
Thanked 129 Times in 94 Posts
I have my batteries charged by the alternator/VR via the battery selecter switch. I also have a 60 W panel that runs to a small charge controller then to the #1 bat. Never had any issues. Elecrical is not my best field so hopefully others will chime in. Dan S/V Marian Claire

Last edited by Marian Claire; 03-31-2013 at 02:25 PM.
Reply With Quote
  #3   IP: 128.183.140.38
Old 04-01-2013, 11:35 AM
edwardc's Avatar
edwardc edwardc is offline
Afourian MVP
 
Join Date: Aug 2009
Location: Laurel, MD
Posts: 2,509
Thanks: 153
Thanked 595 Times in 388 Posts
What you want is something called a charge combiner. It will connect the batteries together when charging, and isolate them the rest of the time.

There are several different types, from a simple relay style one (often sold in WM), to a simple set of high-current isolation diodes (which can cause voltage drop issues), to fancy low voltage-drop electronic ones that have the best of all worlds but cost (lookup Hellroaring Technologies to see one of the better examples of this).

Selection criteria are:
  • Manual/Automatic Operation
  • Power Consumption
  • Voltage drop and its effect on your charging system(s)
  • Cost

The thing you absolutely want to look for in a charge combiner is that it is automatic! The last thing you need is to wake-up one morning and find that both your house and starting banks are dead because you left a manual combiner turned on!

EDIT: Link to Hellroaring Technologies
__________________
@(^.^)@ Ed
1977 Pearson P-323 "Dolce Vita"
with rebuilt Atomic-4


Last edited by edwardc; 04-01-2013 at 01:50 PM.
Reply With Quote
  #4   IP: 206.125.176.5
Old 04-01-2013, 01:13 PM
sastanley's Avatar
sastanley sastanley is online now
Afourian MVP
 
Join Date: Sep 2008
Location: Solomons, MD
Posts: 7,016
Thanks: 1,134
Thanked 600 Times in 442 Posts
Quote:
Originally Posted by edwardc View Post
What you want is something called a charge combiner. It will connect the batteries together when charging, and isolate them the rest of the time.

There are several different types... to a simple set of high-current isolation diodes (which can cause voltage drop issues), ...
I have one of these types and it works great for me. I also have an adjustable voltage regulator on the alternator to compensate for the voltage loss (of approximately 0.70-0.75 volts).

On the other side of the isolator, I have a Gr 24 start battery, and two Gr 29 batteries stacked together as the house bank.

I also have a small solar panel with regulator & alligator clips..My standard practice has been to simply swap this from one battery bank to the other each visit to the boat. The little cheap regulators that go with solar panels will NOT handle the alternator...mine is max rated at 7 amps...good thing my 3.2 watt solar panel churns out a whopping ~220 mA.
__________________
-Shawn
"Holiday" - '89 Alura 35 #109
"Twice Around" - '77 C-30, #511 with original A-4 & MMI manifold - SOLD! (no longer a two boat owner!!)
http://www.moyermarine.com/forums/signaturepics/sigpic3231_6.gif
Reply With Quote
  #5   IP: 71.200.119.246
Old 04-01-2013, 05:30 PM
Hymodyne's Avatar
Hymodyne Hymodyne is offline
 
Join Date: Feb 2013
Location: Salisbury, MD
Posts: 376
Thanks: 53
Thanked 13 Times in 12 Posts
Quote:
Originally Posted by edwardc View Post
What you want is something called a charge combiner. It will connect the batteries together when charging, and isolate them the rest of the time.

There are several different types, from a simple relay style one (often sold in WM), to a simple set of high-current isolation diodes (which can cause voltage drop issues), to fancy low voltage-drop electronic ones that have the best of all worlds but cost (lookup Hellroaring Technologies to see one of the better examples of this).

Selection criteria are:
  • Manual/Automatic Operation
  • Power Consumption
  • Voltage drop and its effect on your charging system(s)
  • Cost

The thing you absolutely want to look for in a charge combiner is that it is automatic! The last thing you need is to wake-up one morning and find that both your house and starting banks are dead because you left a manual combiner turned on!

EDIT: Link to Hellroaring Technologies
Ed, can you recommend one of these for me, based on the set up I have described?

james
Reply With Quote
  #6   IP: 128.183.140.38
Old 04-01-2013, 07:07 PM
edwardc's Avatar
edwardc edwardc is offline
Afourian MVP
 
Join Date: Aug 2009
Location: Laurel, MD
Posts: 2,509
Thanks: 153
Thanked 595 Times in 388 Posts
Quote:
Originally Posted by Hymodyne View Post
Ed, can you recommend one of these for me, based on the set up I have described?

james
Yes, but I'll need to know a little more about your setup, and about what you want.

From what you've written, it sounds like you have two "marine" batteries in parallel for your house bank. I'm assuming there is a smaller, dedicated, starter battery for the engine.

Questions about your setup:
  1. Are the "marine" batteries true, deep-cycle batteries?
  2. Are they wet cells, gel-cells, or AGM?
  3. Is the starter battery Wet, gel, or AGM?
  4. What is the combined amp-hour capacity of the house bank?
  5. What is the amp hour capacity of the starter battery?
  6. What is the full-sun output of your solar charger?
  7. Do you have a "smart" 3-stage charge system on the alternator, or just the standard "automotive" type regulator?
  8. Do you have a shore-power charger?
  9. If so, is it a "smart" 3-stage charger?
  10. Does the shore power charger have multiple outputs for charging multiple batteries?

And some questions about what you want from the system:
  1. How much engine runtime do you want per day to keep your batteries charged?
  2. What is your daily amp-hour power budget for the house bank?
  3. How much do you want to spend?

All of these will affect the type of charging system you want. The charge combiner is just one piece of the system.

The very simplest system is probably a manual Off-1-Both-2 switch. It is cheap, gives you lots of flexibility, but suffers from the big flaw that you must remember to manually switch it from "Both" to just the house bank after you're done motoring. It also allows the big DC transients at starting to effect all of the electronics.

The more complicated but fully automated system would use one of the two-sided Hellroaring combiner/isolators to use all charging sources to charge all batteries, while still keeping the engine/start battery isolated from the house bank and all the electronics. And then there are hybrid systems that use the 4-way switch and a combiner/isolator. Take a look at some of the circuits on the Hellroaring page:

Simple starting battery isolation
More complicated isolation

And I strongly suggest you get & read the battery chapter in Nigel Caulder's book.
__________________
@(^.^)@ Ed
1977 Pearson P-323 "Dolce Vita"
with rebuilt Atomic-4

Reply With Quote
  #7   IP: 206.125.176.5
Old 04-02-2013, 09:27 AM
sastanley's Avatar
sastanley sastanley is online now
Afourian MVP
 
Join Date: Sep 2008
Location: Solomons, MD
Posts: 7,016
Thanks: 1,134
Thanked 600 Times in 442 Posts
Lightbulb

Quote:
Originally Posted by edwardc View Post
And I strongly suggest you get & read the battery chapter in Nigel Caulder's book.
+1! An excellent reference. This is the equivelant of the Moyer Manual for the rest of your boat.
__________________
-Shawn
"Holiday" - '89 Alura 35 #109
"Twice Around" - '77 C-30, #511 with original A-4 & MMI manifold - SOLD! (no longer a two boat owner!!)
http://www.moyermarine.com/forums/signaturepics/sigpic3231_6.gif
Reply With Quote
  #8   IP: 76.68.255.63
Old 04-06-2013, 09:07 PM
Sony2000 Sony2000 is offline
 
Join Date: Dec 2011
Location: Montreal, QC. Canada
Posts: 424
Thanks: 0
Thanked 0 Times in 0 Posts
Can someone tell me the characteristics of this battery charger for wet batteries?
For example will it supply a different rate of charge to each battery according to its needs?
Attached Images
 
Reply With Quote
  #9   IP: 24.152.131.153
Old 04-06-2013, 10:24 PM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
Quote:
Originally Posted by Sony2000 View Post
Can someone tell me the characteristics of this battery charger for wet batteries? For example will it supply a different rate of charge to each battery according to its needs?
That is a two bank three stage charger. The stages are bulk, absorption and float. If connected to two batteries or banks it works best when they are evenly discharged. If unevenly discharged it sends a greater charge rate to the battery with the most need. If connecting to a single battery, a 12 gauge jumper wire is required between output terminals 1 and 2.

Each output is capable of 5 amps output only. They call it a 10 amp charger because it has two independent 5 amp outputs. Fuzzy math if you ask me.

Because of the staging you are not supposed to have a load on the batteries during charging, it throws the stages out of whack.

Hope this helps
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others
Reply With Quote
  #10   IP: 76.68.255.63
Old 04-06-2013, 10:44 PM
Sony2000 Sony2000 is offline
 
Join Date: Dec 2011
Location: Montreal, QC. Canada
Posts: 424
Thanks: 0
Thanked 0 Times in 0 Posts
Great! Thank you. I have two batteries.
Reply With Quote
  #11   IP: 68.204.97.187
Old 04-07-2013, 07:55 AM
hanleyclifford's Avatar
hanleyclifford hanleyclifford is offline
Afourian MVP
 
Join Date: Mar 2010
Posts: 6,978
Thanks: 172
Thanked 280 Times in 226 Posts
Talking

Quote:
Originally Posted by ndutton View Post
That is a two bank three stage charger. The stages are bulk, absorption and float. If connected to two batteries or banks it works best when they are evenly discharged. If unevenly discharged it sends a greater charge rate to the battery with the most need. If connecting to a single battery, a 12 gauge jumper wire is required between output terminals 1 and 2.

Each output is capable of 5 amps output only. They call it a 10 amp charger because it has two independent 5 amp outputs. Fuzzy math if you ask me.

Because of the staging you are not supposed to have a load on the batteries during charging, it throws the stages out of whack.

Hope this helps
This is exactly why multi stage chargers are a bad idea on a boat that ever uses shore power.
Reply With Quote
  #12   IP: 76.68.255.63
Old 04-07-2013, 02:11 PM
Sony2000 Sony2000 is offline
 
Join Date: Dec 2011
Location: Montreal, QC. Canada
Posts: 424
Thanks: 0
Thanked 0 Times in 0 Posts
Quote:
Originally Posted by hanleyclifford View Post
This is exactly why multi stage chargers are a bad idea on a boat that ever uses shore power.
"ever should read never" I assume. And an independant generator (Onan) would drive the multi stage chargers when out to sea. Is that your line of thinking?
Were you out with Jack Daniels last night?
Reply With Quote
  #13   IP: 24.152.131.153
Old 04-07-2013, 02:39 PM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
I can't speak for Hanley but my interpretation was the "no load on the batteries during charging" requirement was the issue. That means no lights, refrigeration, blower, radio, instruments, nuthin', total dark territory during the charging stages.
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others
Reply With Quote
  #14   IP: 76.7.135.1
Old 04-07-2013, 02:49 PM
Marian Claire's Avatar
Marian Claire Marian Claire is offline
Afourian MVP
 
Join Date: Aug 2007
Posts: 1,797
Thanks: 33
Thanked 129 Times in 94 Posts
Same interpretation here.
On a personal note I find the "Jack Daniels" Comment uncalled for. I have had the pleasure of spending time with Hanley and he has always been thoughtful, professional and sharp as a tack. Even at 0755. Dan S/V Marian Claire
Reply With Quote
  #15   IP: 24.152.131.153
Old 04-07-2013, 03:03 PM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
The Jack Daniels comment made me a little uncomfortable as well. I gave him the benefit of the doubt, wrote it off as an attempt at humor.
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others
Reply With Quote
  #16   IP: 68.204.97.187
Old 04-07-2013, 07:36 PM
hanleyclifford's Avatar
hanleyclifford hanleyclifford is offline
Afourian MVP
 
Join Date: Mar 2010
Posts: 6,978
Thanks: 172
Thanked 280 Times in 226 Posts
Talking Allow Me to Clarify

What I mean to say is that a vessel connected to shore power when loads are present should "never" use a multi stage charger as a maintenance charger. The reason for this is that most of the multi stage chargers are keyed on voltage. Hence when a connected system experiences a load such as a refrigerator which will momentarily drop the voltage, the charger will revert to bulk charge. By the type equilibrium voltage has been restored and the refrigerator stops cycling the process is ready to repeat. The batteries thus receive consecutive blasts at very high voltage when they don't really need it. The result is battery boiling.
Reply With Quote
  #17   IP: 68.56.139.11
Old 04-07-2013, 08:18 PM
romantic comedy's Avatar
romantic comedy romantic comedy is offline
Afourian MVP
 
Join Date: May 2007
Location: florida
Posts: 1,912
Thanks: 13
Thanked 118 Times in 100 Posts
Hanley, my statpower specifically says that it is to used as a power supply, while charging batteries. It is a 3 step charger.
That is what the company says.
Reply With Quote
  #18   IP: 68.204.97.187
Old 04-07-2013, 08:27 PM
hanleyclifford's Avatar
hanleyclifford hanleyclifford is offline
Afourian MVP
 
Join Date: Mar 2010
Posts: 6,978
Thanks: 172
Thanked 280 Times in 226 Posts
Talking

http://www.moyermarine.com/forums/at...1&d=1305339750 I had the Pro Sport 20 hard wired while living aboard. It wouldn't stop overcharging the batteries. Now I use the IOTA 30 constant voltage maintainer and rarely add water.
Reply With Quote
  #19   IP: 24.152.131.153
Old 04-07-2013, 08:33 PM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
Quote:
Originally Posted by romantic comedy View Post
Hanley, my statpower specifically says that it is to used as a power supply, while charging batteries. It is a 3 step charger.
That is what the company says.
The instructions for Sony's Guest 2610 specifically say not to have loads on while charging.

Reference:
http://www.marinco.com/files/support...nuals/2610.pdf
page 3, item 2.
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others
Reply With Quote
  #20   IP: 68.56.139.11
Old 04-07-2013, 08:34 PM
romantic comedy's Avatar
romantic comedy romantic comedy is offline
Afourian MVP
 
Join Date: May 2007
Location: florida
Posts: 1,912
Thanks: 13
Thanked 118 Times in 100 Posts
I have not really used 12 volt power when the charger is plugged in. Only a few lights here and there. So I really cant say either way. My charger is 12 years old. The lights on the charger are strange. The 5 amp charge light stays on, and the lights never change. The batteries are always charged. I can see when it is charging, by a volt meter.

Always good to hear other people's experiences.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Dead Batteries after motoring all day scourge32 Electrical 7 07-10-2012 08:46 AM
Wiring spaghetti ndutton Electrical 35 09-07-2011 06:18 AM
Charging batteries in parallel? Bobgrif General Interest 23 08-28-2010 10:18 AM
ACR and Atomic 4 rigspelt Electrical 69 07-13-2009 03:58 PM


All times are GMT -4. The time now is 07:53 PM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2024 Moyer Marine Inc.

All Rights Reserved