Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Discussion Topics > Ignition System

Reply
 
Thread Tools Display Modes
  #1   IP: 108.185.116.22
Old 11-21-2022, 09:28 AM
ejay ejay is online now
Senior Member
 
Join Date: Jul 2022
Posts: 65
Thanks: 4
Thanked 18 Times in 13 Posts
Bad solenoid?

So I had a multi day trip planned with a friend, and at 5 am as we prepared to shove off, I turned the key and my late model A4 would not turn over, much like dead battery. I was crestfallen, as I had never had a problem with either dead batteries or any trouble with the starter.

My friend, who is a farmer, and works with tractors all the time, asked for a screwdriver and he jumped the solenoid connections and the engine fired up just fine. The A4 started up fine the the remainder of the trip, without any help.

Is my solenoid bad? Should I replace it?
Reply With Quote
  #2   IP: 162.245.50.171
Old 11-21-2022, 10:01 AM
Dave Neptune Dave Neptune is online now
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Grove, Oklahoma
Posts: 5,035
Thanks: 711
Thanked 1,289 Times in 839 Posts
First double check the key-switch to be sure the solenoid is getting a full voltage signal.
Did you wiggle and/or keep twisting the key to start? Sometimes a tap with a screw driver or lightly with a hammer will unstick the solenoid too. It is indicative of a sticky solenoid in need of replacement.

If voltage is good from the switch change out the solenoid, They can stick once in a while as they are in a nasty environment.

Dave Neptune
Reply With Quote
The Following User Says Thank You to Dave Neptune For This Useful Post:
TimBSmith (11-21-2022)
  #3   IP: 165.225.20.180
Old 11-21-2022, 10:07 AM
Surcouf's Avatar
Surcouf Surcouf is offline
Afourian MVP, Professor Emeritus
 
Join Date: May 2018
Posts: 361
Thanks: 328
Thanked 163 Times in 123 Posts
when you jump your solenoid this way, you do not just jump the solenoid itself, but also the contact coming from your ignition switch. Said differently, if jumping you solenoid made the trick, you could have an issue with your solenoid, or an issue with the wiring coming from your ignition key (switch if you have one). You would need to check if you get the voltage at the starting terminal of your solenoid when you turn the key to verify if the circuit works properly.

EDIT: Dave's answer is better...
__________________
Surcouf
A nostalgic PO - Previously "Almost There" - Catalina 27 (1979)
Reply With Quote
The Following User Says Thank You to Surcouf For This Useful Post:
TimBSmith (11-21-2022)
  #4   IP: 12.163.75.202
Old 11-22-2022, 12:07 PM
ejay ejay is online now
Senior Member
 
Join Date: Jul 2022
Posts: 65
Thanks: 4
Thanked 18 Times in 13 Posts
Thanks so much for the input! I definitely did not jiggle the switch when we got it going.

I will try to check the voltage going to the solenoid. Excuse my ignorance, but should I use a multimeter to check voltage between the solenoid posts when somebody turns the key?
Reply With Quote
  #5   IP: 162.245.50.171
Old 11-22-2022, 02:10 PM
Dave Neptune Dave Neptune is online now
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Grove, Oklahoma
Posts: 5,035
Thanks: 711
Thanked 1,289 Times in 839 Posts
Yes and no, use the meter from the post to ground with the key at start. To check the key there are two tests first from the hot side to ground then from the "switched to start side" of the key switch when engaged in start. Voltage should be the same voltage.

Disconnect the positive wire from from the coil OR be sure and turn the key yo off so you don't fry the coil by forgetting.

Do close the intake water valve if you do any "cranking" so there's no water encroachment.

Dave Neptune
Reply With Quote
The Following User Says Thank You to Dave Neptune For This Useful Post:
TimBSmith (11-30-2022)
  #6   IP: 32.211.38.220
Old 11-25-2022, 09:13 PM
Al Schober's Avatar
Al Schober Al Schober is offline
Afourian MVP
 
Join Date: Jul 2009
Location: Uncasville, CT
Posts: 2,002
Thanks: 16
Thanked 578 Times in 405 Posts
ejay,
Recommend you have a decent multimeter (one that you trust) on board and be familiar with its use. In the same Ziplock with the multimeter should be a ground cable, clips on each end, capable of reaching from your batteries to either end of the boat.
My meter came with probes having 45 degree points. I sharpened them to needles so I could just push them through insulation.
Our boat systems deal with a nominal 12V system. Some of the loads on the system are high current, which are sensitive to things like bad cables and bad connections.
For example, battery charging. You identify a problem (batteries take too long to charge) and want to fix the issue. Meter tells you the alternator is putting out 14.5 V but only 13.5 V is getting to the battery. A sensitive meter will allow you to check each cable and connection in the circuit. I personally have had cases of 1) too small a ground cable from the battery to the alternator, 2) a bad cable between the engine block and the battery negative, and 3) a bad ground connection between the alternator and the engine block (don't rely on the pivot bolt for a ground).
A multimeter can be your electrical friend.
Reply With Quote
The Following User Says Thank You to Al Schober For This Useful Post:
TimBSmith (11-30-2022)
  #7   IP: 138.207.177.95
Old 11-30-2022, 08:13 AM
joe_db's Avatar
joe_db joe_db is online now
Afourian MVP
 
Join Date: May 2009
Posts: 4,474
Thanks: 49
Thanked 1,026 Times in 721 Posts
FYI -
I had ongoing occasional "no starts" where the ignition was on, but the solenoid would not engage. I now have the start button controlling a relay near the starter, the relay needs very little current to pull in and I have never had a problem starting since.
Attached Images
 
__________________
Joe Della Barba
Coquina
C&C 35 MK I
Maryland USA
Reply With Quote
The Following User Says Thank You to joe_db For This Useful Post:
TimBSmith (11-30-2022)
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Pearson 30 solenoid accessibility uniexpany Electrical 6 09-16-2015 10:20 AM
Bypass Starter Solenoid sailingchance Troubleshooting 64 04-27-2014 10:19 PM
solenoid solenoid joe_db Electrical 1 05-23-2011 04:45 PM
Replacing starter solenoid jacques debauche Electrical 5 06-06-2010 12:40 PM
Solenoid problem columbia28 Troubleshooting 3 08-22-2006 08:04 AM


All times are GMT -4. The time now is 04:32 PM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2024 Moyer Marine Inc.

All Rights Reserved