Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Discussion Topics > Ignition System

Reply
 
Thread Tools Display Modes
  #1   IP: 174.67.229.161
Old 12-05-2013, 02:46 AM
HalcyonS's Avatar
HalcyonS HalcyonS is offline
 
Join Date: Dec 2012
Location: LA
Posts: 493
Thanks: 35
Thanked 10 Times in 9 Posts
Ignition 101

I wrote this summary of (distributor/points) ignition, based on my recent exchanges here. Hopefully others will find it helpful.

How (old school) ignition works.
Or – what I learned from Dave Neptune, Neil Dutton, Hanley Clifford, John Cookson and others.

In a 4 stroke engine, the piston rises and falls twice for each explosion of fuel. Slightly simplistically, its like this -
TDC (Top Dead Center)
Inlet stroke – piston goes down, inlet valve open, gas in.
BDC
Compression stroke - piston goes up, valves closed
TDC - spark ignition of gas mixture
Power stroke - piston goes down, valves closed
BDC
Exhaust stroke - piston goes up, exhaust valve open.
(Both valves are open at the top of the exhaust stroke - referred to as "overlap".)

Battery voltage is supplied to the coil – intermittently- by the points, which are actuated by a cam on the distributor shaft. When the points close, power is supplied to the primary of the coil. The coil, an inductive device, produces a high voltage spike at the moment of the collapse of the induced magnetic field – called flyback voltage. Voltage in multiplied by the primary/secondary relationship.

Points gap is the maximum opening of the points, which is when the shoe rides on the highest point of the cam.

Dwell is the period of time the points are closed, measured in degrees of distributor shaft rotation. Ie this is the period during which the coil ‘charges up’.

The Condensor or capacitor. The primary winding and the capacitor form a ‘tuned circuit’. Stored energy oscillates between the inductor formed by the coil and the capacitor. The condenser, which is connected across the points, is also said to absorb back emf, protecting the points from arcing/burning.

The high voltage spike is passed to respective spark plug by the rotor of the Distributor. As the rotor rotates it contacts the contact for each spark plug lead in succession. The distributor rotates at 1/2 the speed of the crankshaft – thereby synchronizing with every second TDC of each piston!

The distributor is thus two separate machines which happen to be on the same shaft. The points supply power (12v) to the coil, the rotor supplies 20000 volts to the sparkplugs.

Timing refers to the moment of spark ignition with respect to piston TDC. Advanced timing is when ignition occurs before TDC. Retarded ignition when ignition occurs after TDC.

Centrifugal advance is caused by weights and springs under the plate in the distributor upon which the points and condenser are mounted.

There is a useful video at http://www.youtube.com/watch?v=W94iksaQwUo
This discussion is also helpful http://www.ratwell.com/mirror/users....r/ketterin.htm

Timing Adjustment
Timing can be adjusted by loosening the clamp which lock distributor body to block, turning it a few degrees - when the engine is running. Best position is maximum smooth revs for any throttle position.

The manual says - "Take the boat out for a trial run end after bringing engine to normal operating temperature and the boat running at top speed. Loosen the distributor clamp bolt and caefully advance the ignition timing by slowly rotating the distributor body counter-clockwise until the RPM begins to fall off. Then rotate the distributor body in the opposite direction to obtain the greatest number of RPMs without rough running of the engine. The timing is now set properly in the advanced position. The spark automatically adjusts as the engine speed changes."

Distributor Cam Wear
Dave says- The lobe of the cam that wears over the years as it also wears out the many sets of points contact shoes. As the lobe wears there is far less lift (opening) required for the points to come back together at the same spot on the cam lobe, so when setting the "gap" (lift) to "spec" the points will stay open much longer (more degrees of rotation) on what is left of the "cam lobe". This holds the points open longer and gives them far less degrees of rotation closed which is the dwell timing that saturates the coil. (With an EI the timing is fixed and once set does not ever need adjusting unless moved). Once you have set a set of points and set the timing the timing is constantly on the move as the cam shoe on the points and the contacts themselves wear, that is why in the old days if you really took care of your car or boat you constantly had the timing readjusted because it is constantly moving as it wears.

Hanley says- Just make sure that you set your points by means of a dwell meter without regard to point gap specification; then check the actual point gap that yields your required dwell and post that number for us. This will provide useful information about the condition of your distributor cam.

Testing Spark.
Romantic comedy says – Take (spark plug) lead and hold 1/4 inch away from a ground (block). Remember that the rubber cap that fits on the plug will hold the lead away from the ground. Many use a spark plug hooked up to a plug lead, and grounded. Any plug will do. Blue is the best spark. Nice and fat if you can get it.

You can also do a quick and dirty test to the coil. Just hook up 12 volts to the positive side. Then hook up a ground wire to the other side. (no other wires are connected) Take the ground wire and touch to ground and off ground. This will cause a spark. Maybe not the best spark, but a quick test.
__________________
"Halcyon" 36' custom sloop. 8 tons. Glass over strip plank mahoghany. Spruce mast and booms, launched 1969. Original A4.
Reply With Quote
  #2   IP: 24.152.131.153
Old 12-05-2013, 08:58 AM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
That's about it. I would add the reason for advancing the timing. There is a time lag between the introduction of spark and the complete burning of fuel that delivers the driving force. The goal is to have the peak force present at TDC which means the spark needs to initiate combustion a little before TDC. As engine RPM increases the time lag remains the same so the timing needs to advance further to keep up, the reason for the advance weight system.

Ignition 102 might be all the things that can go wrong.
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others
Reply With Quote
  #3   IP: 107.0.6.242
Old 12-05-2013, 10:09 AM
hanleyclifford's Avatar
hanleyclifford hanleyclifford is offline
Afourian MVP
 
Join Date: Mar 2010
Posts: 6,978
Thanks: 172
Thanked 280 Times in 226 Posts
Talking

Ignition 103 would be another argument over the use of a strobe light to set timing to specification before doing the "tweak".
Reply With Quote
  #4   IP: 71.118.13.238
Old 12-05-2013, 10:24 AM
Dave Neptune Dave Neptune is offline
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Grove, Oklahoma
Posts: 5,035
Thanks: 711
Thanked 1,289 Times in 839 Posts
Talking Igniyion 103~S

Forget the trouble and go EI

Dave Neptune
Reply With Quote
  #5   IP: 173.166.26.242
Old 12-05-2013, 10:48 AM
hanleyclifford's Avatar
hanleyclifford hanleyclifford is offline
Afourian MVP
 
Join Date: Mar 2010
Posts: 6,978
Thanks: 172
Thanked 280 Times in 226 Posts
Thumbs up

Quote:
Originally Posted by Dave Neptune View Post
Forget the trouble and go EI

Dave Neptune
Amen to that!
Reply With Quote
  #6   IP: 24.152.131.153
Old 12-05-2013, 10:50 AM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
Quote:
Originally Posted by hanleyclifford View Post
Ignition 103 would be another argument over the use of a strobe light to set timing to specification before doing the "tweak".
Why must there be an argument? Is there a downside to timing with a light?
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others
Reply With Quote
  #7   IP: 107.0.6.242
Old 12-05-2013, 11:09 AM
hanleyclifford's Avatar
hanleyclifford hanleyclifford is offline
Afourian MVP
 
Join Date: Mar 2010
Posts: 6,978
Thanks: 172
Thanked 280 Times in 226 Posts
Talking

Quote:
Originally Posted by ndutton View Post
Why must there be an argument? Is there a downside to timing with a light?
Not that I'm aware of.
Reply With Quote
  #8   IP: 24.152.131.153
Old 12-05-2013, 11:15 AM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
Well then, there's the difference and why I would expect universal acceptance of timing with a light. Other issues we've "discussed" typically have trade-offs, while seemingly solving one problem they introduce others that often require further band-aid fixes with problems of their own.
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others

Last edited by ndutton; 12-05-2013 at 11:22 AM.
Reply With Quote
  #9   IP: 161.213.49.150
Old 12-05-2013, 11:42 AM
JOHN COOKSON JOHN COOKSON is offline
Afourian MVP, Professor Emeritus
 
Join Date: Nov 2008
Posts: 3,500
Thanks: 54
Thanked 855 Times in 629 Posts
Quote:
Originally Posted by HalcyonS View Post
You can also do a quick and dirty test to the coil. Just hook up 12 volts to the positive side. Then hook up a ground wire to the other side. (no other wires are connected) Take the ground wire and touch to ground and off ground. This will cause a spark. Maybe not the best spark, but a quick test.
You can do the same test using the points.
Power up the coil with the points closed. Pull the wire out of the center of the distributor cap and hold it close to the engine to ground. Flick the points open and let them snap close while checking for an arc.
This procedure checks both the coil and points for proper function. If there is still no spark to the plugs the problem is after the coil. (Did you put the rotor in?)

TRUE GRIT
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
A4 original ignition schematic (basic version) rigspelt Ignition System 2 09-30-2021 12:36 PM
A few critical suggestions Don Moyer General Interest 20 02-10-2014 01:45 PM
Ignition Key Breakage Preventer rpowers Electrical 17 05-18-2011 11:46 PM
Intermittent shutdowns - ignition circuit rigspelt Troubleshooting 0 07-05-2010 06:08 AM
Motor random jumpy stuttering, rough and stalling check your electronic ignition. riphonda Troubleshooting 8 07-16-2009 08:44 PM


All times are GMT -4. The time now is 07:28 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2024 Moyer Marine Inc.

All Rights Reserved