Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Discussion Topics > General Maintenance

Reply
 
Thread Tools Display Modes
  #1   IP: 174.95.199.245
Old 01-08-2021, 05:03 PM
C&C32's Avatar
C&C32 C&C32 is offline
Frequent Contributor
 
Join Date: Oct 2020
Posts: 7
Thanks: 0
Thanked 1 Time in 1 Post
2 motors so differnt?

Hi
Been working on my A4 on the boat. Its a newer model then the one in my garage. And noticed the valve lifters sit so different in the seats.
Is this normal?
Attached Images
  
Reply With Quote
  #2   IP: 174.95.199.245
Old 01-08-2021, 05:05 PM
C&C32's Avatar
C&C32 C&C32 is offline
Frequent Contributor
 
Join Date: Oct 2020
Posts: 7
Thanks: 0
Thanked 1 Time in 1 Post
Top Picture is the older motor, bottom the one in boat. As you can see the lifters sit quite a bit higher and the old motor sit flush with block. ?
Reply With Quote
  #3   IP: 69.250.111.245
Old 01-08-2021, 10:51 PM
sastanley's Avatar
sastanley sastanley is offline
Afourian MVP
 
Join Date: Sep 2008
Location: Solomons, MD
Posts: 6,749
Thanks: 750
Thanked 426 Times in 320 Posts
Hello there..I have had my head in the valve train, but I don't know the answer to your question.
However, since you on that side of the engine..between the flywheel and the valve opening there should be an embossed 6 digit date...i.e. 041976,, which is the date the block was cast on my '77 boat. Ignore the more prominent embossing number directly inboard of the flame arrestor...I am not sure what that is but maybe the mold for the block..it is usually 288xxx or something.

Folks that know more than me may know some details based on the age of the engine.
__________________
-Shawn
"Twice Around" - '77 Catalina 30, #511 with original A-4 & MMI manifold.
She is even happier with fresh paint on the topsides!

http://www.moyermarine.com/forums/signaturepics/sigpic3231_6.gif

Last edited by sastanley; 01-08-2021 at 10:54 PM.
Reply With Quote
  #4   IP: 155.186.122.195
Old 01-09-2021, 11:36 AM
Dave Neptune Dave Neptune is offline
Afourian MVP, Professor Emeritus
 
Join Date: Jan 2007
Location: Lake Arrowhead Ca.
Posts: 4,365
Thanks: 513
Thanked 620 Times in 431 Posts
Could just be a casting difference, no biggie~~seen lots of those. Could be longer lifters so they sit higher for easier adjustment~~no biggie. Could also be a "reground cam" which would drop the lifters deeper into the bores for the smaller diameter cam~~again no biggie. I have played with "cam base diameters" when stroking many "V" style motors. The reduction was needed to clear the main journal throughs and rod connections because the now larger diameter would hit the "std" cam causing nasty failures.

My guess is it is just a different casting when the basic block was "changed". We know of many changes and some are even interchangeable and/or adaptable.

Dave Neptune
Reply With Quote
  #5   IP: 174.95.199.245
Old 01-09-2021, 11:59 AM
C&C32's Avatar
C&C32 C&C32 is offline
Frequent Contributor
 
Join Date: Oct 2020
Posts: 7
Thanks: 0
Thanked 1 Time in 1 Post
Great input, Thanks.
One on the boat is a 80's A4 the one in garage is 1974.
I realized the difference when I had practised adjusting the clearance on the one on the work bench. Once I went to the boat and using the same tools realized they didn't fit the same. The thick wrenches I was using on the old engine didn't fit on the new one very well. So sourced some thinner ones so I could see what I was doing.

cheers
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Good guys in Richmond, VA for starter motors, alternators, pumps, carbs ILikeRust Good Guys 3 05-27-2015 08:32 AM
One of Don's A4 exchange motors Derek Hewson General Interest 1 09-08-2014 07:35 PM
New & some rebuilt parts - LOTS - 3 motors SeattleIanReilly For Sale - Engines and Engine Parts 2 02-11-2013 01:07 AM
A history of Universal Motors marthur General Interest 1 05-09-2010 05:02 PM
How likely to damage motors are cold overnight temps.? Paul_NY General Interest 1 04-05-2007 07:42 AM


All times are GMT -4. The time now is 07:25 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2021, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2021 Moyer Marine Inc.

All Rights Reserved