Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Owner Discussion Groups > Discussion Groups > Tartan

Reply
 
Thread Tools Display Modes
  #1   IP: 24.61.95.61
Old 01-31-2020, 11:44 AM
ArtJ ArtJ is online now
 
Join Date: Sep 2009
Posts: 2,177
Thanks: 221
Thanked 65 Times in 50 Posts
Source of replacement for spreader T34C

I am in possible need of a replacement port spreader on my Tartan 34c

hull number 119 with double lowers

Does anyone know the exact dimensions and the original mfg source?

Thanks

Art
Reply With Quote
  #2   IP: 107.77.104.100
Old 01-31-2020, 01:20 PM
LordGothington LordGothington is offline
Senior Member
 
Join Date: Feb 2018
Posts: 26
Thanks: 4
Thanked 0 Times in 0 Posts
I had to get new spreaders fabricated for my 1965 Tartan 27. The shop was able to contact Tartan directly and get the specifications.
Reply With Quote
  #3   IP: 24.61.95.61
Old 01-31-2020, 03:36 PM
ArtJ ArtJ is online now
 
Join Date: Sep 2009
Posts: 2,177
Thanks: 221
Thanked 65 Times in 50 Posts
I will check with Tartan Thanks

The Tartan owner groups also used to have a lot of very detailed information, unfortunately, that information seems to have been lost or moved from the site
Reply With Quote
  #4   IP: 32.211.28.40
Old 01-31-2020, 10:31 PM
Al Schober's Avatar
Al Schober Al Schober is offline
Afourian MVP
 
Join Date: Jul 2009
Location: Uncasville, CT
Posts: 2,002
Thanks: 16
Thanked 578 Times in 405 Posts
I would think the new port spreader should be the same length as your current stbd spreader.
Reply With Quote
  #5   IP: 24.61.95.61
Old 02-01-2020, 07:32 AM
ArtJ ArtJ is online now
 
Join Date: Sep 2009
Posts: 2,177
Thanks: 221
Thanked 65 Times in 50 Posts
Al
That is true Spreaders are both up there , however;
I am unable to climb the mast while boat is covered until spring in N.E.
Hoping
to have a replacement on hand ahead of time to avoid delays in
spring and single trip up mast if possible

Thanks

Art
Reply With Quote
  #6   IP: 100.40.58.241
Old 02-01-2020, 10:09 AM
jcwright jcwright is offline
Afourian MVP
 
Join Date: Jul 2012
Posts: 158
Thanks: 5
Thanked 99 Times in 75 Posts
Art,

I have my spreaders in the basement, waiting for me to install new lights. They are original parts off our T34C (#266, which is the single lower shroud design). If it would help to have measurements of my spreaders, let me know.

jack.
Reply With Quote
The Following User Says Thank You to jcwright For This Useful Post:
ArtJ (02-01-2020)
  #7   IP: 24.61.95.61
Old 02-01-2020, 10:33 AM
ArtJ ArtJ is online now
 
Join Date: Sep 2009
Posts: 2,177
Thanks: 221
Thanked 65 Times in 50 Posts
Thanks Jack

Yes,

I would love to have measurements!

I am also interested in: length ,diameter, both ends dimensions and size of hole in mast end .

My port spreader is currently sitting horizontal. It should be pointing slightly upwards to bisect the shroud angles.
I asked a helper to check this and he replied that the Spreader mast end
appeared to be loose on this port side only spreader He did not remove the tape
and unfortunately his english is not too good.
I will need to go up myself and eyeball it in the Spring

My boat has double lowers yours may not, but maybe spreader is the same

Is it also possible to post a picture of the spreader?

Thank you very very much

Art
Reply With Quote
  #8   IP: 100.40.58.241
Old 02-01-2020, 02:39 PM
jcwright jcwright is offline
Afourian MVP
 
Join Date: Jul 2012
Posts: 158
Thanks: 5
Thanked 99 Times in 75 Posts
Hello again Art.

I've taken some measurements and pictures of my spreader. The first page has the sketches of the top and side view, and some notes. The second page has photos. Ignore the masking tape; I put that on so I could mark the various stations on the extrusion. Let me know if you need any other information.

Here's the link to the PDF file:

https://drive.google.com/file/d/16xj...ew?usp=sharing

jack.
Reply With Quote
The Following User Says Thank You to jcwright For This Useful Post:
ArtJ (02-02-2020)
  #9   IP: 24.61.95.61
Old 02-02-2020, 09:19 AM
ArtJ ArtJ is online now
 
Join Date: Sep 2009
Posts: 2,177
Thanks: 221
Thanked 65 Times in 50 Posts
Smile

Jack

A Fantastic document !!

Excellent


Maybe would be worth your posting to T34 Owners group to archive this valuable detailed resource information for others ?


Thank you again very much appreciated


Art
Reply With Quote
  #10   IP: 24.61.95.61
Old 02-02-2020, 09:39 AM
ArtJ ArtJ is online now
 
Join Date: Sep 2009
Posts: 2,177
Thanks: 221
Thanked 65 Times in 50 Posts
Jack


Is it possible to send this document as a ordinary pdf that can be saved or printed outside of google ?


Thanks
Reply With Quote
  #11   IP: 100.40.58.241
Old 02-02-2020, 10:28 AM
jcwright jcwright is offline
Afourian MVP
 
Join Date: Jul 2012
Posts: 158
Thanks: 5
Thanked 99 Times in 75 Posts
The MMI forum interface is not my forte, but I've tried to attach the PDF file to this response. Please let me know if the attachment fails.

I hope you are able to get the replacement spreader you need. I thought about referring you to an outfit in my area (RI) that claims to have parts that match, but then I read their recent reviews.

Let me know if you need more information.

Jack.
Attached Images
File Type: pdf Spreader diagram.pdf (356.7 KB, 919 views)
Reply With Quote
The Following User Says Thank You to jcwright For This Useful Post:
ArtJ (02-02-2020)
  #12   IP: 24.61.95.61
Old 02-02-2020, 10:40 AM
ArtJ ArtJ is online now
 
Join Date: Sep 2009
Posts: 2,177
Thanks: 221
Thanked 65 Times in 50 Posts
Jack

Thanks again
I am able to save and print this attached pdf now



Many Thanks


Art

BTW I keep my boat in Boston RI is nearby
Reply With Quote
  #13   IP: 24.152.132.140
Old 02-02-2020, 10:51 AM
ndutton's Avatar
ndutton ndutton is offline
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 9,619
Thanks: 198
Thanked 2,208 Times in 1,425 Posts
Art, now that you have it you can post it to the Tartan group yourself.
__________________
Neil
1977 Catalina 30
San Pedro, California
prior boats 1987 Westsail 32, 1970 Catalina 22
Had my hands in a few others
Reply With Quote
  #14   IP: 100.40.58.241
Old 02-02-2020, 11:25 AM
jcwright jcwright is offline
Afourian MVP
 
Join Date: Jul 2012
Posts: 158
Thanks: 5
Thanked 99 Times in 75 Posts
Hello Neil (and Art).

It's OK with me if anyone wants to post the document to the Tartan group. I stopped using that forum when it migrated from its original site to its new one. I may be out of date, but many files and other resources seem not to have survived.

I do think the spreader measurements would be more helpful if they included cross sections at a few points. I haven't figured out how to get those yet, but I'll add them when I do.

Jack.
Reply With Quote
  #15   IP: 24.61.95.61
Old 02-02-2020, 12:51 PM
ArtJ ArtJ is online now
 
Join Date: Sep 2009
Posts: 2,177
Thanks: 221
Thanked 65 Times in 50 Posts
Jack

I am not a member any longer as well .
The t34c site changed from the original
Reply With Quote
  #16   IP: 24.61.95.61
Old 02-09-2020, 09:05 AM
ArtJ ArtJ is online now
 
Join Date: Sep 2009
Posts: 2,177
Thanks: 221
Thanked 65 Times in 50 Posts
Quote:
Originally Posted by jcwright View Post
Hello Neil (and Art).

It's OK with me if anyone wants to post the document to the Tartan group. I stopped using that forum when it migrated from its original site to its new one. I may be out of date, but many files and other resources seem not to have survived.

I do think the spreader measurements would be more helpful if they included cross sections at a few points. I haven't figured out how to get those yet, but I'll add them when I do.

Jack.
Hi Jack

I noticed on your photos that there appears to be a single filled hole
inboard about a inch of the other mounting holes. Does this
filled hole exist on your other spreader as well?
Could the spreader
have been attached by a single bolt originally and possibly used on a different point of attachment?

Regards

Art
Reply With Quote
  #17   IP: 100.40.58.241
Old 02-09-2020, 09:52 AM
jcwright jcwright is offline
Afourian MVP
 
Join Date: Jul 2012
Posts: 158
Thanks: 5
Thanked 99 Times in 75 Posts
Hello Art.

I checked both spreaders. The (possibly) filled holes you mention are on both sides of both spreaders. It's difficult to measure where the center of each hole might be, as the shapes are irregular. They are approximately on the centerline of the spreader, and about 2" from the inboard edge. They are in the reinforced section I mentioned in an earlier post, which is about double the wall thickness of the rest of the spreader.

There is no evidence that the 'holes' extended through the reinforced section; inside the spreader there are no welds or other filler where a might have been.

So, it's a bit of a mystery to me what these spots are. I've attached a photo.

Let me know if you need any other information.

jack.
Attached Images
 
Reply With Quote
  #18   IP: 72.69.36.126
Old 02-09-2020, 12:45 PM
tenders tenders is offline
Afourian MVP
 
Join Date: May 2007
Location: Harlem YC, City Island, NY
Posts: 1,439
Thanks: 46
Thanked 259 Times in 170 Posts
That spreader in many ways resembles the lowers from my ‘69 Ericson 32 - which were made of Sitka spruce. The shape is not that complicated and aside from the length, very little needs to be precise as long as it fits the mounting hardware.

I made replacements of my four spreaders over a weekend from a slab of raw wood and just a few woodworking tools - borrowed my brother-in-law’s planer and router, and the rest was bandsaw, drilling, and sanding. I have no particular woodworking skills but it was all very straightforward once the wood was planed to the right thickness. Coated them all with West epoxy with UV hardener, and (initially) two coats of Brightside, then after ten years recoated them with epoxy and three coats of Perfection.

Don’t make too many assumptions about the symmetry of the port and starboard pieces. It’s possible that your aluminum part was made from a casting of a wooden version with a different attachment method, which itself may not have been identical to the piece on the other side. This could explain the phantom hole in the casting.

What are “double lower spreaders”? How many spreaders have you got on that thing?

Last edited by tenders; 02-13-2020 at 07:51 AM.
Reply With Quote
The Following User Says Thank You to tenders For This Useful Post:
ArtJ (02-09-2020)
  #19   IP: 100.40.58.241
Old 02-09-2020, 01:35 PM
jcwright jcwright is offline
Afourian MVP
 
Join Date: Jul 2012
Posts: 158
Thanks: 5
Thanked 99 Times in 75 Posts
I believe Art's earlier post about 'double lowers' was referring to double lower shrouds. Earlier T34Cs had two lower shrouds per side. The later design (like mine) had one per side. As far as I'm aware, the mast height did not change. I suspect the spreader dimensions didn't change either.
Reply With Quote
The Following User Says Thank You to jcwright For This Useful Post:
ArtJ (02-09-2020)
  #20   IP: 24.61.95.61
Old 02-09-2020, 02:28 PM
ArtJ ArtJ is online now
 
Join Date: Sep 2009
Posts: 2,177
Thanks: 221
Thanked 65 Times in 50 Posts
Thanks Jack

I was wondering about the holes and if the spreader had been repurposed.


Regarding Spreader design and placement I read a article from This Old Boat?

or Practical Sailor ?which cautioned about spreaders being the most common point of mast failure, It cautions that the shroud angle above and below the
spreader be equal to avoid a mast failure. It also cautioned that spreader design is not be be taken lightly . If I can find the article again I will post the location. I think I googled "spreaders design / failure or something similar

Regards and thanks
Art
Reply With Quote
  #21   IP: 24.61.95.61
Old 02-09-2020, 02:37 PM
ArtJ ArtJ is online now
 
Join Date: Sep 2009
Posts: 2,177
Thanks: 221
Thanked 65 Times in 50 Posts
Smile

The Spreader article is from the SEPT/Oct 2019 issue 128 of Good Old Boat
"Equal Angles Equal Forces " Pg17 " correct adjustment may save your rig"



https://goodoldboat.com/equal-angles-equal-forces/




Regards
Art

Last edited by ArtJ; 02-09-2020 at 02:42 PM.
Reply With Quote
The Following User Says Thank You to ArtJ For This Useful Post:
GregH (02-10-2020)
  #22   IP: 108.172.148.210
Old 02-09-2020, 03:50 PM
Marty Levenson Marty Levenson is offline
Senior Member
 
Join Date: Nov 2004
Location: Bowen Island, BC
Posts: 679
Thanks: 91
Thanked 42 Times in 36 Posts
Good stuff

Thanks for the information. I can imagine tugging on a stuck flag when heeled over.....!
__________________
Marty
1967 Tartan 27
Bowen Island, BC

Reply With Quote
  #23   IP: 100.40.58.241
Old 02-09-2020, 03:50 PM
jcwright jcwright is offline
Afourian MVP
 
Join Date: Jul 2012
Posts: 158
Thanks: 5
Thanked 99 Times in 75 Posts
I've attached the best copy I have of Sparkman & Stephens' sail plan for the T34C. It shows the designed length of the spreader (3') and the height of the spreader base at the mast. Let me know if there is any other information you need.

Jack.
Attached Images
File Type: pdf T34C Sail Plan.pdf (1.27 MB, 934 views)
Reply With Quote
The Following User Says Thank You to jcwright For This Useful Post:
ArtJ (02-09-2020)
  #24   IP: 24.61.95.61
Old 02-09-2020, 05:32 PM
ArtJ ArtJ is online now
 
Join Date: Sep 2009
Posts: 2,177
Thanks: 221
Thanked 65 Times in 50 Posts
Thanks Jack
That is a better copy than mine and proves that the spreaders are the same
on both single and double lowers versions

Thabks

Art
Reply With Quote
  #25   IP: 100.40.58.241
Old 02-15-2020, 11:38 AM
jcwright jcwright is offline
Afourian MVP
 
Join Date: Jul 2012
Posts: 158
Thanks: 5
Thanked 99 Times in 75 Posts
Art,

I've attached an updated drawing of the T34C spreader, this time including the cross-sections that were missing from the earlier file.

Jack.
Attached Images
File Type: pdf Tartan 34c Spreader Diagram.pdf (362.1 KB, 946 views)
Reply With Quote
The Following User Says Thank You to jcwright For This Useful Post:
ArtJ (02-19-2020)
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Throttle lever arm replacement? Clucas Fuel System 3 08-26-2019 04:45 PM
Replacement fuel tank pick up line source pdecker General Interest 10 04-15-2019 09:14 PM
Choke knob replacement? gfatula General Maintenance 7 12-29-2014 03:51 PM
Gas Shut Off Valve Replacement domagami Fuel System 8 05-07-2008 05:16 PM


All times are GMT -4. The time now is 07:50 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2024 Moyer Marine Inc.

All Rights Reserved