Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Discussion Topics > Cooling System

Reply
 
Thread Tools Display Modes
  #1   IP: 174.206.65.172
Old 07-22-2021, 10:24 AM
edminor edminor is offline
Frequent Contributor
 
Join Date: Jul 2021
Location: Oldhams, VA
Posts: 5
Thanks: 0
Thanked 0 Times in 0 Posts
Wrench size for 1/2" temperature sensor

Does anyone know the wrench size required to remove the 1/2" water temperature sending unit? Have searched to forum, but have not been able to find it. Thanks in advance.
Reply With Quote
Old 07-22-2021, 10:45 AM
joe_db
This message has been deleted by joe_db. Reason: www
  #2   IP: 138.207.177.95
Old 07-22-2021, 10:49 AM
joe_db's Avatar
joe_db joe_db is offline
Afourian MVP
 
Join Date: May 2009
Posts: 4,474
Thanks: 49
Thanked 1,026 Times in 721 Posts
I can't recall offhand, but I do remember buying in impact socket to get it out. The standard socket was going to round it off.
Reply With Quote
  #3   IP: 47.142.141.196
Old 07-22-2021, 01:28 PM
JOHN COOKSON JOHN COOKSON is offline
Afourian MVP, Professor Emeritus
 
Join Date: Nov 2008
Posts: 3,500
Thanks: 54
Thanked 855 Times in 629 Posts
DO NOT GO AFTER THE SENDING UNIT WITH A OPEN END WRENCH. It will round the soft brass. I used a long closed end wrench and a hammer and the sending unit loosened fairly easily. Start the engine and let it warm up to operating temperature then, while the engine is running, try to loosen the sending unit. The heat + vibration will help it loosen.
I don't remember the wrench size. You can span the sending unit with a open end adjustable wrench then measure the jaw opening to get a rough idea of the proper wrench size.

ex TRUE GRIT
Reply With Quote
  #4   IP: 172.56.23.194
Old 07-22-2021, 01:30 PM
jcwright jcwright is offline
Afourian MVP
 
Join Date: Jul 2012
Posts: 158
Thanks: 5
Thanked 99 Times in 75 Posts
My temp sending unit (stamped ‘8D17’) pairs with an Isspro gauge. I believe it is the 1/2” npt version. It takes a 7/8” wrench.
Reply With Quote
  #5   IP: 146.168.151.69
Old 07-22-2021, 01:50 PM
edminor edminor is offline
Frequent Contributor
 
Join Date: Jul 2021
Location: Oldhams, VA
Posts: 5
Thanks: 0
Thanked 0 Times in 0 Posts
Thanks to everyone for the replies. Leaving tomorrow to work on the boat, and needed to know which wrenches to pack. I have a deep 7/8” six-point socket and a strong bar, will be sure to include them
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Faulty Temperature Sensor? heinzb Cooling System 1 07-04-2019 08:05 PM
Broken temperature sensor MightyMike Cooling System 5 08-31-2018 11:10 AM
temperature gauge and alarm sensors on same fitting capnward Electrical 5 05-17-2013 10:33 AM
Misc Stories and Removing that stuck temperature sensor... marthur General Maintenance 5 07-22-2012 03:16 PM
What size screw for the oil pressure sensor fuel switch? Baltimore Sailor General Maintenance 1 04-11-2008 10:51 AM


All times are GMT -4. The time now is 05:49 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2024 Moyer Marine Inc.

All Rights Reserved