|
#1
IP: 24.152.132.140
|
||||
|
||||
Finding TDC the easy way
A while back we had a tool concept for finding the compression stroke in a cylinder, critical when setting timing from scratch, without peering or inserting anything into the spark plug hole. Remember this?
Well it struck me as a pretty cool idea so I finally got around to making one and testing it out. I sacrificed an old spark plug by breaking off the porcelain, drilling out the electrode and grinding off the arm on the bottom, added a balloon to the top, threaded it into the #1 spark plug hole finger tight only and turned the engine over by hand. Once you know you're on the compression stroke you view the crankshaft roll pin for vertical alignment. Way cool.
__________________
Neil 1977 Catalina 30 San Pedro, California prior boats 1987 Westsail 32, 1970 Catalina 22 Had my hands in a few others |
#2
IP: 141.239.218.236
|
||||
|
||||
Neil-
IF you decide to mass produce... can we have a variety of color choices on the balloons?
__________________
-Jerry 'Lone Ranger' 1978 RANGER 30 |
#3
IP: 24.152.132.140
|
||||
|
||||
Yes, you may . . .
__________________
Neil 1977 Catalina 30 San Pedro, California prior boats 1987 Westsail 32, 1970 Catalina 22 Had my hands in a few others |
#4
IP: 141.239.218.236
|
||||
|
||||
__________________
-Jerry 'Lone Ranger' 1978 RANGER 30 |
#5
IP: 67.176.202.26
|
|||
|
|||
Very cool. Only thing I can add is that on this site you will either "learn" or get "entertained".
|
#6
IP: 76.66.159.112
|
||||
|
||||
Quote:
And that is why they call it enterlearnment! |
#7
IP: 137.103.82.227
|
||||
|
||||
Quote:
|
#8
IP: 32.211.28.40
|
||||
|
||||
Well, this has been an amusing thread!
Just what I needed during this isolation. Spring trip to NOLA cancelled, instead we got to visit Loch Down. I hear that even Nessie is now in Loch Down. So, all this is just to keep from putting your thumb over the spark plug hole? No, the idea of acetylene balloons is new to me. Haven't tried one. Do they make your voice funny?? Another week or two of this and we can start a thread on vegetable guns. I've still got my potato cannon out in the shed - SpudZooka! I had the design for a radish pistol, but never made one. |
#9
IP: 24.152.132.140
|
||||
|
||||
One thing I noticed with the balloon indicator - - you can turn the engine very slowly by hand and still get a good indication. Oh yeah, you can turn the engine with TWO hands.
__________________
Neil 1977 Catalina 30 San Pedro, California prior boats 1987 Westsail 32, 1970 Catalina 22 Had my hands in a few others |
#10
IP: 137.103.82.227
|
||||
|
||||
Quote:
|
#11
IP: 76.176.224.167
|
||||
|
||||
Interesting glitch
With this foolproof compression stroke indicator I recently performed a from-scratch timing exercise that was 180° out. Embarrassed, how could I have possibly messed up something as simple as this? I removed the spark plugs, installed the balloon indicator in cylinder #1, turned the crank by hand CCW facing the flywheel, balloon inflated, continued turning the crank until the roll pin was vertical, set the distributor rotor to #1. What could be easier?
Babbling in disbelief it took me an hour to figure it out. The engine had not run in a very long time, like years. The crank was not frozen, compression test showed good numbers on all cylinders, water jacket pressure test was successful so the conclusion was we had a viable block and air pump worthy of an effort to get her to run again. After replacement and rebuilding of several components, with the coil wire removed I cranked for about 30 seconds to get some oil pressure without combustion. This cranking was done with the raw water intake thru-hull open. In a perfect world I would not have done that but the thru-hull valve was stuck open and I did not want to risk a bigger problem by breaking it trying to close. [Mis]setting the timing as described above followed. It turned out that there was enough water in the waterlift muffler to seal off the muffler exit. This caused a backpressure to develop in the cylinder on the exhaust stroke thereby inflating the balloon indicator and a false result. I removed the water hose to the exhaust water injection fitting and extended it into a bucket to stop the waterlift from filling any more until I had the engine running. This also vented the exhaust so an accurate TDC could be determined and the timing reset. I therefore recommend removing the water injection hose to vent the exhaust when using the balloon indicator to avoid the mistake I made.
__________________
Neil 1977 Catalina 30 San Pedro, California prior boats 1987 Westsail 32, 1970 Catalina 22 Had my hands in a few others |
The Following 4 Users Say Thank You to ndutton For This Useful Post: | ||
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Finding TDC the easy way | ndutton | Ignition System | 26 | 05-14-2020 10:02 AM |
Finding TDC (top dead center) | jpian0923 | Drawings and Schematics | 4 | 09-18-2016 06:25 PM |
Easy distributor question | positron | Ignition System | 15 | 03-15-2012 05:29 PM |
If torqueing was easy , | Laker | General Interest | 14 | 01-27-2011 02:51 PM |
An Easy Fix | rpowers | Troubleshooting | 3 | 07-26-2010 04:58 PM |