Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Discussion Topics > Drive Train / Propellers

Reply
 
Thread Tools Display Modes
  #1   IP: 174.55.63.120
Old 09-08-2021, 07:04 PM
jwin10143@aol.com jwin10143@aol.com is offline
Member
 
Join Date: Jun 2021
Posts: 4
Thanks: 2
Thanked 1 Time in 1 Post
Reversing gear removal Help



I need some advise in removing the reversing gear so in can put my direct drive reversing gear instead on this new A4 witch it had a V-Drive that i already remove.Has anyone remove the reversing gear with out removing the upper half rear casing? If no. How do you break loose the seals of the upper half casing? It appears that the permatex is very difficult to loosen up. I do not want to hurt or damage the engine or the housing.
Attached Images
 
Reply With Quote
  #2   IP: 134.41.132.177
Old 09-09-2021, 09:48 AM
Mo's Avatar
Mo Mo is offline
Afourian MVP
 
Join Date: Jun 2007
Location: Halifax NS,
Posts: 4,443
Thanks: 250
Thanked 379 Times in 253 Posts
Hi,
So if I understand correctly, this engine is out of the boat and you just want to change out the reversing gear. If that is the case I did it about a year ago. I had a spare engine with the reduction gear that had to be switched to a direct drive. What I did was remove all the bolts and two dowels. It popped apart with a few smacks of a huge rubber hammer.

The tricky part for me was putting it back on. You will fine two dowels that have to be tapped out. Mine moved no problem, again with the rubber hammer. Those dowels do not go back in until after you have placed the replacement drive on and bolted it up.

Putting the new drive on: You have to be very careful because there is a 90 degree angle between the reversing gear housing and the block. It is crucial that the junction there is perfect. The dowels in place caused a problem for me so I left them out. They caused the gasket to bunch up which would have resulted in an oil leak. It would then have to come back off and be done right.

So what I did after screwing up the new gasket was use permatex black heavy duty, high heat, engine gasket maker. I cleaned all surfaces, then had a friend help me place the reversing gear on perfectly so that that 90 degree corner mating surface has gasket maker. I then put in two bolts finger tight to ensure it was lined up and left it sit there for about 4 hours. After that I came back and tightened everything up. Personally, I didn't put the dowels back in because there are bolts around them as well and it's been fine.

The care of placing the new one was key as many people get leaks in the corner of the joint where the reversing gear and the engine meet.

I installed the engine in the boat a couple of days later and started it and low and behold found a leak. Initially thought I screwed up that joint at the 90 degree angle but was relieved to see oil drip from the water pump bolt. Removing the water pump again and resealing fixed it.

It's been a year and I've motored the engine about 100 hours this year. Did a 440 nautical mile trip where I motored something like 92 hours without a problem of any kind.

When I got into that it was the first time Id had the reversing gear off one of these and I spoke with Al Schober who had way more knowledge than me. It went very smooth and I was so pleased.
__________________
Mo

"Odyssey"
1976 C&C 30 MKI

The pessimist complains about the wind.
The optimist expects it to change.
The realist adjusts the sails.
...Sir William Arthur Ward.
Reply With Quote
The Following 2 Users Say Thank You to Mo For This Useful Post:
jwin10143@aol.com (09-10-2021), TimBSmith (09-09-2021)
  #3   IP: 174.55.63.120
Old 09-10-2021, 05:48 PM
jwin10143@aol.com jwin10143@aol.com is offline
Member
 
Join Date: Jun 2021
Posts: 4
Thanks: 2
Thanked 1 Time in 1 Post
Reversing gear removal Help

Thank .I will keep that in mind. Will keep everyone posted on this. The one in the pic is the new engine and it had V- drive in it.Thats what i am removing and placing the direct reversing gear and shaft with the old one.
Reply With Quote
The Following User Says Thank You to jwin10143@aol.com For This Useful Post:
Mo (09-10-2021)
Reply

Tags
reverse gear removal, reversing gear

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
still have reversing gear problems. weremeer Reversing Gear 6 06-25-2011 01:09 PM
problem with reversing gear. weremeer Reversing Gear 8 03-26-2011 03:59 PM
Replacing gaskets on reversing gear and reduction gear housings phorvati Troubleshooting 1 10-06-2008 03:10 PM
Reversing Gear Slippage Issues? SEMIJim Reversing Gear 9 07-16-2008 09:48 PM


All times are GMT -4. The time now is 10:11 PM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2021, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2021 Moyer Marine Inc.

All Rights Reserved