In reading this forum, I noticed a large number of comments to spare parts carried on board. Does anyone have a recommended spare parts list?
Spare Parts
Collapse
This is a sticky topic.
X
X
-
This is a really good question, and one that is fraught with myriad variables and personal preferences. For this reason, every time I propose a spare parts list, I feel like I'm raising a flag out of a foxhole that everyone starts shooting at, e.g. why do I list this, but not that, etc.
So, with all my scars, I'm probably in the best position to make the first posting of a list and offer others to jump in and comment. Perhaps our Forum can finally come up with a sensible spare parts list.
I would only offer one suggestion, which is that we consider in this first list the needs of a cruising experience, which I would define as being out of range of our home port for at least two or three weeks. Feel free to comment even on this logic, but my thought is that dealing with a major breakdown (of boat or engine) that one might encounter after being "on the road" for six months to a year, would be beyond the scope of most or our readers.
I'll try to look in now and then, and when all the ideas are in, I'll consolidate the list.
Here's my list:
SUGGESTED SPARE PARTS AND TOOLS FOR CRUISING
The following items should only be considered as a starting point in devising a list of spare parts and tools. Please add or detract from the list as appropriate in meeting your specific needs. Remember, your best assurance against being caught in a threatening situation (or working your way out of one) depends not only on the spare parts that you might have on board, but on a thorough understanding of the different systems in your engine.
SPARE PARTS:
1) Coil.
2) Four new spark plugs.
3) Spare fuel pump.
4) Spare water pump (a spare impeller may suffice if no snap ring is required and the pump is less than 5 seasons old or has less than 500 operating hours).
5) Three or four feet of engine water hose, fuel line (with appropriate sized hose clamps), and a small roll of electrical wire (12 or 14 gauge).
6) A roll of good quality electrical tape.
7) Spare elements for any filters you have on board.
8) Spare fuses.
9) Spare alternator (optional).
RECOMMENDED TOOLS (In addition to normal hand tools):
1) A small digital volt/ohmmeter.
2) A three-foot length of 14 gauge wire with a ring terminal on one end and a clip on the other. This wire can be used to "hot wire" the ignition system in the event of a failure of the primary circuit within the boat's electrical system.
3) Electrical crimping tool and a small supply of ring terminals, butt splices, etc.
4) Remote starter switch (available for about $10 at most auto parts stores).
5) A 12 volt light with alligator clips to use for checking continuity.
6) MMI Service and Overhaul Manual
-
-
Spare Parts and Tools
I would add an alternator belt (probably more important than an alternator, especially if you stay fairly close to home). Suggestion for "normal hand tools: sufficient tools to install any spare parts you carry. Add anything to that basic list you think might be useful for troubleshooting.
Comment
-
-
Clint,
The hose sizes on a Moyer Marine rebuilt engine are 5/16" (Coast Guard Type A) for the fuel line, and 1/2" water hose. The hose size between the back of the manifold and the exhaust inlet fitting would depend on your particular boat, but this hose is usually 5/8" or 3/4".
Regards,
DonLast edited by Don Moyer; 06-24-2005, 06:14 PM.
Comment
-
-
I would add a spark plug socket
and some way to prime your fuel lines (a bulb type, Tempo?)
________
Honda VF400FLast edited by 1973 Ericson; 01-28-2011, 12:59 AM.
Comment
-
-
Besides tools arleady mentioned (voltmeter, etc.), tools I've found valuable are:
1) 'Short' SAE cresent wrench set. Good for getting nuts off in tight quarters, especially for carburator. Minimal length of wrenches facilitates working in tight spaces. Also pack a short adjustable cresent wrench.
2) Basic SAE 1/4" socket set.
3) Elecrical wire tool for removing sheathing and crimping up to 16G wire
4) Lockjaw pliers
5) Plenty of screwdrivers (if your clumsy like me, you'll drop of few into areas beyond immediate reach)
6) Sharp razor
Hardware to have onboard:
1) collection of #6, #8, #10, 1/4", 5/16", & 3/8" nuts and bolts. Stainless definitely, panhead AND oval preferably, of different lengths. This can become quite an extensive collection of fasteners, but I've found them invaluable in repairing problems at sea.
2) Cotter pins, clevis pins, and rings, and hose clamps of various diameters.
3) Electrical terminals for 10G to 18G wire, with adequate diameter of terminal ends to fasten onto battery, coil, alternator, and devices.
4) Spare gaskets for Carb to manifold, Carb upper to carb lower, and waterpump. In extreme instances, water jacket, head and manifold gaskets would also be desireable to have onboard, and they're inexpensive.
5) Marval Mystery Oil and Carb CleanerJohn Kenan
Ericson 29, Carried Away
Efland, NC
Comment
-
-
#9 UnapprovedTools Tip: Costco has a great set of rachetable SAE wrenches on sale for about $20 right now. Those are worth the money for quick and dirty work in tossing seas... or any work, come to that.
Add a hacksaw, adjustable wrenches, an inspection mirror, and some needle nose pliers. Plus twine, a spool of wire, and duct tape. And bring along that stubby screwdriver that you filed down to a smooth oval for tapping into the gasket and seperating old metal parts.
I would also like to have a list of "quick tips" for temporary get-back-to-land fixes for patching up fuel leaks, fixing compression, overriding electrical failures, improving a leaky gasket, giving an impeller a little more life, clearing a blockage etc. etc. The last thing I would enjoy was getting all queazy over the engine on a tossing sea. If anyone has such a list, pass it on, would you?
PS: Not strictly A4, but one sailing buddy, who taught me the word "redundancy" takes fully-charged power tools (saw and drill) in case he needs to patch a hole with a piece of teak bulkhead (or cut greater access through to the engine). He also has a nice Honda generator ready to go, gasoline powered.
Comment
-
-
Not quite off topic but...
I carry a 24" bolt cutter which can be used for cutting away the rigging (among other things) in an emergency. Off topic because I can't think how having this tool would help with the A4.Tartan 27 #328 owner born 1958
A4 and boat are from 1967
Comment
-
-
how to ID my engine
Hi, there peoples. It's my first post here. I just bought E27(1978) with a4 in it.
My question is how do I know which model of engine I have? If I don't know what I got, how do I make list of spare parts to get?
I am not familiar with A4s at all...it looks nice and simple, but, I'm sure there are tricks to run and tune it.
I have uploaded a couple of pix that might help identifying it...can you tell me which gaskets are most likely need to be changed if I have water in the oil???
Thanks,
Mac
Comment
-
Comment