Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Search Forums

Showing results 1 to 12 of 12
Search took 0.01 seconds.
Search: Posts Made By: C&C32
Forum: Troubleshooting 07-06-2021, 08:08 PM
Replies: 5
Views: 1,439
Posted By C&C32
Thanks for the reply. Will have a look at the...

Thanks for the reply.
Will have a look at the alignment this weekend. As for the stuffing box, I have not done much to it. Seemed to be working well with a very slight drip underway. So assumed it...
Forum: Troubleshooting 07-05-2021, 04:39 PM
Replies: 5
Views: 1,439
Posted By C&C32
New propeller vibration?

Hi
I have a 1980 c&c 32. It had a plastic/composite prop on it when I bought it. It had a slight chip in it on one of the blades ( two blade prop). Boat ran great with it. No vibration so I left...
Forum: Troubleshooting 03-24-2021, 06:55 AM
Replies: 7
Views: 1,521
Posted By C&C32
Mine is the same. So wondering the same thing. ...

Mine is the same. So wondering the same thing.
Sometimes I end up putting the gear selector slightly in reverse position to put it in true neutral.
Looking forward to the responses.
Forum: Troubleshooting 02-25-2021, 02:20 PM
Replies: 5
Views: 1,316
Posted By C&C32
Thanks for the info. I do run a mixed coolant....

Thanks for the info.
I do run a mixed coolant. And will fully inspect the strainer and the water muffler.
cheers
Forum: Troubleshooting 02-24-2021, 11:12 AM
Replies: 5
Views: 1,316
Posted By C&C32
Coolant leak in cold temps?

Hi
I live in Toronto Canada. In the winters we can drop to -20C at certain times. I winterize the A4 with automotive glycol antifreeze each winter. Raw water cooled motor.
I run a dry bilge all...
Forum: General Maintenance 01-09-2021, 10:59 AM
Replies: 4
Views: 1,436
Posted By C&C32
Great input, Thanks. One on the boat is a...

Great input, Thanks.
One on the boat is a 80's A4 the one in garage is 1974.
I realized the difference when I had practised adjusting the clearance on the one on the work bench. Once I went to...
Forum: General Maintenance 01-08-2021, 04:05 PM
Replies: 4
Views: 1,436
Posted By C&C32
Top Picture is the older motor, bottom the one in...

Top Picture is the older motor, bottom the one in boat. As you can see the lifters sit quite a bit higher and the old motor sit flush with block. ?
Forum: General Maintenance 01-08-2021, 04:03 PM
Replies: 4
Views: 1,436
Posted By C&C32
2 motors so differnt?

Hi
Been working on my A4 on the boat. Its a newer model then the one in my garage. And noticed the valve lifters sit so different in the seats.
Is this normal?
Forum: General Interest 12-24-2020, 08:58 AM
Replies: 3
Views: 1,183
Posted By C&C32
Thanks. I have allot left to do and find parts...

Thanks.
I have allot left to do and find parts
- have to locate and install a reverse gear
- install a distributor and re wire
- find a carb and electronic fuel pump and install
-...
Forum: Electrical 12-23-2020, 05:00 PM
Replies: 5
Views: 1,073
Posted By C&C32
Thanks for the reply. Was wondering what it was...

Thanks for the reply. Was wondering what it was for. So I may just remove it to clean up the wiring.
Cheers
Stephen
Forum: Electrical 12-23-2020, 01:09 PM
Replies: 5
Views: 1,073
Posted By C&C32
Alternator switch?

Hi
This boat is fairly new to me. Atomic4 runs well. But a question I have is this alternator controller? Anyone know how it works? Why you would have one?
I have not touched it since owning the...
Forum: General Interest 12-23-2020, 01:00 PM
Replies: 3
Views: 1,183
Posted By C&C32
Winter project

Hi
My first post here. But this site has been a fantastic place for information for my winter project.
Spare A4 build. Been putting it together with spare parts and a couple generous donations. ...
Showing results 1 to 12 of 12

 
Forum Jump

All times are GMT -4. The time now is 02:14 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2024 Moyer Marine Inc.

All Rights Reserved