Forum: For Sale - Engines and Engine Parts
02-14-2014, 09:55 PM
|
Replies: 11
Views: 3,795
Carbs
I have at least 2 of the 4-bolt carbs.
|
Forum: For Sale - Engines and Engine Parts
02-12-2014, 09:43 PM
|
Replies: 11
Views: 3,795
|
Forum: For Sale - Engines and Engine Parts
01-06-2014, 11:39 PM
|
Replies: 11
Views: 3,795
Flame arrest
Maybe, how would I identify an early model one from a late model one? I have several.
|
Forum: For Sale - Engines and Engine Parts
01-06-2014, 02:41 PM
|
Replies: 11
Views: 3,795
Update - more parts
I dug into the box a little bit and also found an entire transmission/gearbox and housing, a distributer and accessory gear drive, 2 starters, access plates for both sides of the engine, and flame...
|
Forum: For Sale - Engines and Engine Parts
01-05-2014, 03:13 PM
|
Replies: 11
Views: 3,795
Large box of A4 parts
Hi all-
I have a VERY large box of A4 parts including several carbs, exhaust manifolds, an oil pan (yes, the whole bottom half of the motor casing), a water cooled exhaust pipe, a standpipe style...
|
Forum: For Sale - Engines and Engine Parts
05-05-2012, 01:09 AM
|
Replies: 4
Views: 3,248
Exhaust manifolds
I have two early model exhaust manifolds (which I got in a lot of misc. parts I purchased). They are useless to me since my exhaust exits the engine at the front and I'd be happy to mate them up with...
|
Forum: Wanted to Buy - Engines and Engine Parts
05-05-2012, 01:08 AM
|
Replies: 3
Views: 2,837
Exhaust manifold
I'd be interested in a used exhaust manifold if anyone has one lying around. I would need the late model version with the block off plate since my exhaust exits out the front of the engine.
On...
|
Forum: Exhaust System
06-08-2010, 08:56 PM
|
Replies: 10
Views: 8,187
Yes, it is just as you describe. I have a...
Yes, it is just as you describe. I have a straight (4 inch I think) piece of pipe out of the flange to a 45, then about an 8 inch piece which goes under the bulkhead and to a 90. From the 90 I have...
|
Forum: General Interest
06-06-2010, 02:06 PM
|
Replies: 7
Views: 3,705
You didn't mention if you had disconnected the...
You didn't mention if you had disconnected the exhaust pipe from the flange, but if you did, this is another potential spot for leakage. I was suprised to find that I could go another full turn...
|
Forum: Tartan
06-06-2010, 01:57 PM
|
Replies: 8
Views: 13,998
Jacques -
How much did Don charge you for the...
Jacques -
How much did Don charge you for the standpipe? Do you have pictures? Just curious at this point, since I believe I have solve my problems with a slightly different approach. It never...
|
Forum: Exhaust System
06-06-2010, 01:51 PM
|
Replies: 10
Views: 8,187
I had a similar installation to yours on my...
I had a similar installation to yours on my Tartan 30 (#518) when I bought it 6 months ago. You can see my progression through this process on the thread titled "A developing story" in the general...
|
Forum: Electrical
05-07-2010, 03:05 PM
|
Replies: 25
Views: 18,426
|
Forum: General Interest
05-03-2010, 11:01 PM
|
Replies: 7
Views: 4,586
|
Forum: Electrical
05-03-2010, 08:35 PM
|
Replies: 30
Views: 54,282
|
Forum: General Interest
05-03-2010, 08:02 PM
|
Replies: 7
Views: 4,586
|
Forum: Fuel System
04-29-2010, 09:53 AM
|
Replies: 3
Views: 3,163
My oil safety switch is attached (via the oil...
My oil safety switch is attached (via the oil filter kit) to the forward (flywheel side) oil port. There shouldn't be any problem with it. I also have a mechanical oil pressure gauge in the middle...
|
Forum: General Interest
04-28-2010, 11:28 AM
|
Replies: 38
Views: 14,773
|
Forum: Overhaul
04-27-2010, 10:46 AM
|
Replies: 5
Views: 3,693
|
Forum: Cooling System
04-26-2010, 11:09 PM
|
Replies: 14
Views: 6,488
If you can spread the snap ring like you said,...
If you can spread the snap ring like you said, try having someone pull the shaft out while pushing on the back of the impeller. If you can slide the shaft out, the snap ring should no longer be a...
|
Forum: General Interest
04-26-2010, 10:43 PM
|
Replies: 38
Views: 14,773
|
Forum: General Interest
04-26-2010, 12:34 AM
|
Replies: 38
Views: 14,773
Continuation
As an aside, everything I'm doing is from the engine, manually operating the choke and throttle.
Searching the forums convinced me that my problem was either a vacuum leak or a cruddy carb. I...
|
Forum: General Interest
04-25-2010, 11:59 PM
|
Replies: 38
Views: 14,773
Another continuation
Well, hopefully I won't regret saying this, but I feel that my most recent saga is nearly at its end. I took the boat out today and it ran beautifully! It ran at idle for over an hour without the...
|
Forum: Exhaust System
04-25-2010, 12:02 AM
|
Replies: 16
Views: 7,809
|
Forum: Cooling System
04-19-2010, 10:37 AM
|
Replies: 115
Views: 26,234
Hanley -
Are you referring to the groove...
Hanley -
Are you referring to the groove that the belt rides in? If I wanted to try to pull it, how would a puller attach? It would have to grab the sheave somehow, right?
Thanks for the...
|
Forum: Cooling System
04-19-2010, 12:17 AM
|
Replies: 115
Views: 26,234
|