Forum: Electrical
08-18-2021, 04:00 PM
|
Replies: 4
Views: 1,026
|
Forum: Electrical
08-16-2021, 05:49 PM
|
Replies: 4
Views: 1,026
Thanks for the explanation and understood.
...
Thanks for the explanation and understood.
For whatever reason, the positive lead on my blower was connected to a positive terminal on the instrument panel already. The ground was the only one...
|
Forum: Electrical
08-16-2021, 03:08 PM
|
Replies: 4
Views: 1,026
Blower motor wiring short
I had an intermittent short in my blower motor wiring that I finally resolved. Sometimes the blower would work, sometimes not, sometimes if I jiggled the throttle, the motor would come on. Often,...
|
Forum: Announcements
08-10-2020, 01:09 AM
|
Replies: 34
Views: 6,180
|
Forum: General Interest
07-01-2020, 06:01 PM
|
Replies: 167
Views: 45,689
|
Forum: Reversing Gear
06-22-2020, 05:34 PM
|
Replies: 3
Views: 1,611
|
Forum: Reversing Gear
06-22-2020, 01:56 PM
|
Replies: 3
Views: 1,611
clevis pin stuck?
I'm trying to replace my shifter cable, but can't get the clevis pin out. The cotter pin came out, but for the life of me I can't get the connecting pin out.
Am I just lame, or is there a trick?...
|
Forum: Announcements
06-18-2020, 04:32 PM
|
Replies: 18
Views: 11,332
|
Forum: Overhaul
05-06-2020, 09:34 AM
|
Replies: 20
Views: 4,465
You're right, tenders. It's coming from inside...
You're right, tenders. It's coming from inside the cylinder. I'll tighten the plugs more than I have in the past and see how that changes things.
#3 sometimes has a little oil. #1 and #2 have no...
|
Forum: Overhaul
05-06-2020, 12:01 AM
|
Replies: 20
Views: 4,465
|
Forum: Electrical
05-05-2020, 09:38 AM
|
Replies: 5
Views: 2,148
|
Forum: Electrical
05-03-2020, 02:05 PM
|
Replies: 5
Views: 2,148
Cut wire - any ideas?
This white wire behind my instrument panel looks to be heavy gauge (same as red wire to ammeter) and obviously serves no purpose other than to pose existential questions. Why is it there?
This is...
|
Forum: Ignition System
05-03-2020, 01:54 PM
|
Replies: 41
Views: 10,474
|
Forum: Overhaul
05-03-2020, 01:30 PM
|
Replies: 20
Views: 4,465
|
Forum: Overhaul
05-02-2020, 03:32 PM
|
Replies: 20
Views: 4,465
|
Forum: Overhaul
05-02-2020, 02:55 PM
|
Replies: 20
Views: 4,465
|
Forum: Overhaul
04-28-2020, 12:13 AM
|
Replies: 20
Views: 4,465
|
Forum: Overhaul
04-27-2020, 09:16 AM
|
Replies: 20
Views: 4,465
Ando: Yes, correct carb kit was installed. New...
Ando: Yes, correct carb kit was installed. New fuel filter this year.
ronstory: Q1: motor not not frequently driven hard for extended periods. New marina only takes 10-15 minutes to get to sailing...
|
Forum: Overhaul
04-26-2020, 12:41 AM
|
Replies: 20
Views: 4,465
Low compression - next steps?
Hi All,
My engine has never been "peppy" and it usually hesitates as I increase throttle. I finally completed the 2 stage compression test with the following results. Both were with a cold engine....
|
Forum: Helpful Videos
04-20-2020, 12:01 AM
|
Replies: 2
Views: 4,030
|
Forum: Ignition System
04-11-2020, 09:34 PM
|
Replies: 41
Views: 10,474
|
Forum: Ignition System
04-11-2020, 09:06 PM
|
Replies: 41
Views: 10,474
|
Forum: Troubleshooting
02-03-2020, 04:35 PM
|
Replies: 9
Views: 2,141
|
Forum: Drive Train / Propellers
08-29-2019, 08:22 PM
|
Replies: 3
Views: 1,723
|
Forum: Drive Train / Propellers
08-28-2019, 06:00 PM
|
Replies: 3
Views: 1,723
Shaft wear - tolerance?
So the stuffing box drip turned into a stream and I finally got the guts (and tools) to tackle a repack. While "in there," I measured the shaft inside and outside the stuffing box. Inside...
|