Forum: Cooling System
12-20-2021, 05:37 PM
|
Replies: 4
Views: 2,366
145 to 180 degrees, cycling up and down
Hi. I noticed recently that my engine temp is cycling between temperate ranges of around 140 or 145 F and about 180 F when run at speed (2000 rpm is about max with my folding prop on my C&C 36).
...
|
Forum: General Interest
09-03-2021, 09:44 PM
|
Replies: 4
Views: 1,510
Thank you Moyer Marine!
I needed an MMI flange water pump to be delivered next day this week and the team there got it done. The pump is beautifully made and an improvement over the Oberdorfer I had before with many special...
|
Forum: Reversing Gear
07-13-2020, 05:22 PM
|
Replies: 9
Views: 3,197
I've got reverse like I've never had it in the...
I've got reverse like I've never had it in the two years I've owned the boat. It now behaves as everyone said it should.
I had a new, hardened steel part made to remain in the shift yoke with a...
|
Forum: Reversing Gear
06-26-2020, 08:42 PM
|
Replies: 9
Views: 3,197
Thank you all for the replies. Al is a total...
Thank you all for the replies. Al is a total expert.
Has anyone ever seen a band brace that is so worn as mine?
Our next plan is to live with the alignment issue and make a reversing bar...
|
Forum: Reversing Gear
06-15-2020, 08:18 AM
|
Replies: 9
Views: 3,197
|
Forum: Reversing Gear
06-08-2020, 01:54 PM
|
Replies: 9
Views: 3,197
Reversing Ability
I've started working with a local expert to improve the reversing ability. No matter what adjustment either of us made, the boat would only hold reverse at low engine speed and only with light touch...
|
Forum: Fuel System
11-17-2019, 10:33 PM
|
Replies: 11
Views: 3,102
The advice on this forum is so good. Thank you...
The advice on this forum is so good. Thank you and thank you to Don for his video on typical carburetor issues. Well worth buying. Should have bought it earlier.
We found a missing piece in the...
|
Forum: Fuel System
11-17-2019, 12:03 PM
|
Replies: 11
Views: 3,102
|
Forum: Fuel System
11-16-2019, 11:42 PM
|
Replies: 11
Views: 3,102
|
Forum: Fuel System
11-16-2019, 11:41 PM
|
Replies: 11
Views: 3,102
Thank you, Dave. I am not sure on the float...
Thank you, Dave. I am not sure on the float valve settings. Do you know what the spec should be for it and how to set it up?
The motor now starts and runs without choke up to that high idle,...
|
Forum: Fuel System
11-16-2019, 06:54 PM
|
Replies: 11
Views: 3,102
Rebuilt carb and now will not run at cruising rpm
Hello,
I’ve worked with a friend to rebuild my carburetor after the float sometimes stuck and it got so that it would only run with partial choke.
My friend installed the Moyer rebuild kit and...
|
Forum: Troubleshooting
08-19-2019, 10:02 AM
|
Replies: 23
Views: 9,786
|
Forum: Troubleshooting
07-14-2019, 06:20 PM
|
Replies: 23
Views: 9,786
|
Forum: Troubleshooting
06-25-2019, 10:47 AM
|
Replies: 23
Views: 9,786
|
Forum: Troubleshooting
06-24-2019, 06:15 PM
|
Replies: 23
Views: 9,786
|
Forum: Troubleshooting
06-24-2019, 03:16 PM
|
Replies: 23
Views: 9,786
|
Forum: Troubleshooting
06-24-2019, 01:32 PM
|
Replies: 23
Views: 9,786
To go back, the system has never been great in...
To go back, the system has never been great in reverse since I've owned the boat for a year. I have tightened the reversing nut to help twice and have seen some benefit there. I found that I could...
|
Forum: Troubleshooting
06-24-2019, 11:26 AM
|
Replies: 23
Views: 9,786
Here is a picture of all reassembled. After...
Here is a picture of all reassembled. After taking the picture, tightened the reverse nut to pull things together, but there still is risk of the reverse bar losing the yolk.
I wonder if the...
|
Forum: Troubleshooting
06-24-2019, 09:55 AM
|
Replies: 23
Views: 9,786
|
Forum: Troubleshooting
06-24-2019, 09:41 AM
|
Replies: 23
Views: 9,786
Thank you. I was able to get the transmission...
Thank you. I was able to get the transmission all back together and working to some extent. I have the forward detent back and reverse is not tight enough.
I do worry that the reverse bar which...
|
Forum: Troubleshooting
06-23-2019, 01:38 PM
|
Replies: 23
Views: 9,786
I've reconnected the reverse bar and am finding...
I've reconnected the reverse bar and am finding that, just as Al noted, I'm still not getting the fingers over the cone for forward gear. The videos I showed were taken with the shift cable to the...
|
Forum: Troubleshooting
06-22-2019, 08:44 AM
|
Replies: 23
Views: 9,786
Jack,
Thank you very much. I realized the...
Jack,
Thank you very much. I realized the shift bar had become disconnected while waiting for the post to be approved.
Im researching now how to repair and the link you provided looks quite...
|
Forum: Troubleshooting
06-21-2019, 10:50 PM
|
Replies: 23
Views: 9,786
Can’t shift into forward detent or get reverse
I have an Atomic 4 in a C&C 36 with pedestal shift and a friend left it in reverse for a week. My shift handle is stiff and so it remained in reverse after he shut off the engine even though there...
|