Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Search Forums
Register FAQ Community Today's Posts Search

Showing results 1 to 15 of 15
Search took 0.00 seconds.
Search: Posts Made By: Oaktown27
Forum: Troubleshooting 06-19-2023, 01:50 PM
Replies: 41
Views: 3,208
Posted By Oaktown27
I did follow most of the process you outlined. I...

I did follow most of the process you outlined. I tore down the carb, cleaned the jets with a wire, cleaned the bowl, new gasket. Didn't adjust or check the spacing in the float. Perhaps this is...
Forum: Troubleshooting 06-16-2023, 04:23 PM
Replies: 41
Views: 3,208
Posted By Oaktown27
Back at it, and installed a fuel pressure gage...

Back at it, and installed a fuel pressure gage and checked for air leaks. Fuel pressure is a constant 3 psi (not under load).

I did take out the Gypsy Rose last week, and still couldn't get it...
Forum: Troubleshooting 06-06-2023, 10:31 AM
Replies: 41
Views: 3,208
Posted By Oaktown27
Prop was cleaned during the hull cleaning last...

Prop was cleaned during the hull cleaning last week. Interesting development yesterday. Looked at the distributor again to make sure the mechanical advance was free to move (is free and functioning),...
Forum: Troubleshooting 06-05-2023, 01:22 PM
Replies: 41
Views: 3,208
Posted By Oaktown27
OK, I am back as I was waiting to to get the hull...

OK, I am back as I was waiting to to get the hull scraped and prop cleaned.

Went over yesterday, and the motor started right up, but unfortunately the power issue still exists. I did check the...
Forum: Troubleshooting 05-12-2023, 02:11 PM
Replies: 41
Views: 3,208
Posted By Oaktown27
All good advice, going to take a look at the prop...

All good advice, going to take a look at the prop and check the choke plate before I do anything else. Will let you all know the outcome.
Forum: Troubleshooting 05-10-2023, 10:55 AM
Replies: 41
Views: 3,208
Posted By Oaktown27
Thanks, I did check the plugs and the wires. ...

Thanks, I did check the plugs and the wires.

Wires are in the correct order. Wish it was as simple as that. Also, the plugs looked a little "sooty", so might think this is also a function of...
Forum: Troubleshooting 05-07-2023, 07:09 PM
Replies: 41
Views: 3,208
Posted By Oaktown27
Still having power issues - Round two

I am back. I started with an overheating problem coupled with a no power problem. I did a tune up, rebuilt the hot riser on the exhaust, new impeller, and raw water valve to diver the cooling water....
Forum: Cooling System 02-25-2023, 05:59 PM
Replies: 29
Views: 4,445
Posted By Oaktown27
Yup, Krud it was. Probably going to slip a fuel...

Yup, Krud it was. Probably going to slip a fuel filter in the line. The mechanical fuel pump cup was gross, and I probably should buy a replacement. Since it is a copper line from the pump to carb,...
Forum: Cooling System 02-20-2023, 04:41 PM
Replies: 29
Views: 4,445
Posted By Oaktown27
Happy Ending

Happy to report that after pulling the carb and cleaning the jets, cleaning the pump bowl and adding the scavenge tube, power has been restored!

Thanks to all for the support and suggestions. Have...
Forum: Cooling System 02-11-2023, 10:58 AM
Replies: 29
Views: 4,445
Posted By Oaktown27
Finished building the hot exhaust riser. Thanks...

Finished building the hot exhaust riser. Thanks to the local Grainger as it seems black pipe is not a stocked item any more at the local plumbing shop.

Pulled the carburetor, and plan to clean...
Forum: Cooling System 01-31-2023, 10:29 PM
Replies: 29
Views: 4,445
Posted By Oaktown27
Black Pipe or Galvanized.

I am building a new hot section. I have seen both Galvanized used and black pile. Was leaning toward black pipe, but getting the sections are/will be a chore.

Is Black Pipe the way to go?
...
Forum: Cooling System 01-27-2023, 01:31 PM
Replies: 29
Views: 4,445
Posted By Oaktown27
Progress Update

Appreciate the help to date. Now that California has dried out a bit I have finished a bunch of other maintenance.

Put in a bypass valve and replaced the impeller.
Scraped the hull near the...
Forum: Cooling System 01-01-2023, 07:27 PM
Replies: 29
Views: 4,445
Posted By Oaktown27
Compression Test done. Waiting on parts.

Thanks. I do have a feeling the intake might be plugged, so will take the suggested approach by taking off the intake hose.

I have had this for two years, so the maintenance is needed as I didn't...
Forum: Cooling System 12-31-2022, 01:15 PM
Replies: 29
Views: 4,445
Posted By Oaktown27
Thanks Dave for the guidance. Truely appreciate...

Thanks Dave for the guidance. Truely appreciate it.

The through hull valve was open as I closed it when I pulled the pump cover. Was interesting as I see these typically have an o-ring or gasket,...
Forum: Cooling System 12-30-2022, 06:56 PM
Replies: 29
Views: 4,445
Posted By Oaktown27
No Thermostat? What...

Hi all, new to the forum, and so happy to have found it. I picked up a '72 Santana 27 during Covid to keep my sanity. The Atomic Four was running and a bit of a mystery to me on how it operated...
Showing results 1 to 15 of 15

 
Forum Jump

All times are GMT -4. The time now is 04:01 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2024 Moyer Marine Inc.

All Rights Reserved