Forum: Cooling System
06-01-2016, 05:20 PM
|
Replies: 26
Views: 13,042
|
Forum: Cooling System
04-29-2009, 04:05 PM
|
Replies: 27
Views: 16,134
|
Forum: General Interest
04-25-2009, 05:49 PM
|
Replies: 12
Views: 5,368
|
Forum: General Maintenance
04-23-2009, 03:12 PM
|
Replies: 2
Views: 5,540
|
Forum: General Interest
04-21-2009, 10:53 AM
|
Replies: 12
Views: 5,368
Spring prep, changing the Impellor:
I took the time to change my impellor prior to launch this season, as I had not changed it in some time. The last time was when my impellor broke and I changed it while the boat was in the water.
...
|
Forum: Cooling System
01-02-2009, 02:08 PM
|
Replies: 10
Views: 16,275
Impeller
I replace my impeller every three years, but as I read through the correspondence, the 'snap O pin' is something that I have never seen on the shaft and have never installed. As a matter of fact, I...
|
Forum: Ignition System
06-18-2007, 01:34 PM
|
Replies: 5
Views: 4,408
|
Forum: Ignition System
06-17-2007, 03:47 PM
|
Replies: 5
Views: 4,408
Possible Timing Problem
Don,
I just replaced my exhaust system which had finally cracked after some 33 years. Everything seems to be working fine.
My latest problem may be a timing problem, but I do not believe it...
|
Forum: Troubleshooting
05-08-2007, 11:56 AM
|
Replies: 5
Views: 6,222
|
Forum: Troubleshooting
05-06-2007, 10:55 AM
|
Replies: 5
Views: 6,222
Cracked Exhaust
I removed the exhaust hose from the waterlift muffler, only to discover that the metal exhaust split at the water entry point, solving the moisture and steam on the outside of the hot section of the...
|
Forum: Troubleshooting
04-30-2007, 03:34 PM
|
Replies: 5
Views: 6,222
Running rough and steaming
Don,
I cannot tell you how much I appreciate your forum and your advice; it has been an incredible resource.
I have a 1973 C&C 27 and have had great luck with my Atomic 4 until just prior to...
|
Forum: Ignition System
03-26-2007, 04:53 PM
|
Replies: 3
Views: 9,070
Idle Valve adjustments.
I have a very unusual situation where my low idle mixture needle valve has a tendency to tighten itself down. The way we found this was, the engine would idle fine, but when under power we would...
|
Forum: General Maintenance
08-09-2006, 09:28 AM
|
Replies: 11
Views: 11,521
|
Forum: General Maintenance
07-26-2006, 04:25 PM
|
Replies: 11
Views: 11,521
Oil Pressure
Don, is there another way to check oil pressure in the event of a faulty gauge?
Is there somewhere on th engine to attach a temporary oil pressue gauge?
thanks
|
Forum: Troubleshooting
07-08-2005, 09:38 PM
|
Replies: 5
Views: 4,285
|
Forum: Troubleshooting
07-04-2005, 09:58 PM
|
Replies: 5
Views: 4,285
Hi Don and John,
Well after going back and...
Hi Don and John,
Well after going back and looking at all of the ignition and tune up components with no found errors, the next step was look at the fuel service situation. We rechecked...
|
Forum: Troubleshooting
07-03-2005, 11:46 AM
|
Replies: 5
Views: 4,285
|
Forum: Troubleshooting
06-26-2005, 08:56 PM
|
Replies: 5
Views: 4,285
Where to go next?
I'm having a very frustrating experience with my engine. Starts like a charm, runs at lower RPM and cooler (120 F not 140 F) than it did and for some reason after running the engine for a long period...
|