Forum: Troubleshooting
06-15-2014, 09:14 PM
|
Replies: 40
Views: 14,001
|
Forum: Troubleshooting
06-12-2014, 07:37 PM
|
Replies: 40
Views: 14,001
|
Forum: Troubleshooting
06-11-2014, 02:36 PM
|
Replies: 40
Views: 14,001
|
Forum: Troubleshooting
06-11-2014, 01:32 PM
|
Replies: 40
Views: 14,001
|
Forum: Troubleshooting
06-11-2014, 11:47 AM
|
Replies: 40
Views: 14,001
I was out in the garage experimenting when you...
I was out in the garage experimenting when you posted, Dave, so I ended up gently prying it off with a small screwdriver. It was not loose, it was on there fairly secure. I will sand around it and...
|
Forum: Troubleshooting
06-11-2014, 11:19 AM
|
Replies: 40
Views: 14,001
Exactly how does one remove the Venturi tube?
...
Exactly how does one remove the Venturi tube?
The Moyer Manual simply says to remove it, without specifying how. It looks like it can be popped out with a flat head screwdriver, but I'd rather not...
|
Forum: Troubleshooting
06-11-2014, 09:20 AM
|
Replies: 40
Views: 14,001
Hello Dave,
The PO rebuilt the exhaust,...
Hello Dave,
The PO rebuilt the exhaust, along with most everything else, within the past two or three years. I would estimate that it has less than 100 sailing hours on it.
Is there a way to...
|
Forum: Troubleshooting
06-10-2014, 09:43 PM
|
Replies: 40
Views: 14,001
|
Forum: Troubleshooting
06-10-2014, 06:31 PM
|
Replies: 40
Views: 14,001
|
Forum: Troubleshooting
06-10-2014, 09:31 AM
|
Replies: 40
Views: 14,001
Is that the hard, copper line that screws into...
Is that the hard, copper line that screws into the block close to the carb? If so, yes, it is connected and dry.
I forget what the purpose of that tube is now, but I remember reading about it in...
|
Forum: Troubleshooting
06-10-2014, 09:08 AM
|
Replies: 40
Views: 14,001
Many thanks, seapadrik!
I have both the...
Many thanks, seapadrik!
I have both the reciprocating tool and a dremel, so I should be set to make an access panel. One thing I can't quite tell from your picture, though, is what's on the back...
|
Forum: Troubleshooting
06-10-2014, 12:21 AM
|
Replies: 40
Views: 14,001
Ha, thanks Mark!
Actually, when I get the...
Ha, thanks Mark!
Actually, when I get the gas leak fixed I'm going to take a wire brush and a can of spray paint to it to clean it up even more. The PO did a wonderful job with her, and I'm...
|
Forum: Troubleshooting
06-09-2014, 10:27 PM
|
Replies: 40
Views: 14,001
|
Forum: Troubleshooting
06-09-2014, 09:57 PM
|
Replies: 40
Views: 14,001
|
Forum: Troubleshooting
06-09-2014, 06:01 PM
|
Replies: 40
Views: 14,001
Finding the source of a gas leak
Hi folks,
My late model A4 has a gas leak somewhere around the carb. I've done a thorough inspection of the fuel lines from the electric fuel pump(which is installed on the bulkhead). The in-line...
|
Forum: Overhaul
05-21-2014, 05:11 PM
|
Replies: 35
Views: 9,634
bigal,
To post pictures to this thread, you...
bigal,
To post pictures to this thread, you first need to upload the pictures to a photo sharing site, like photobucket, or dropbox.
From there, you can copy the URL to the pic, then paste...
|
Forum: Troubleshooting
10-28-2013, 03:07 PM
|
Replies: 12
Views: 6,270
|
Forum: Troubleshooting
10-28-2013, 02:56 PM
|
Replies: 12
Views: 6,270
Well, now I'm confused even more(I know, not...
Well, now I'm confused even more(I know, not difficult in my case :rolleyes:).
Don't all late model A4's have the same size manifold drain plugs? Or are you saying that it's possible that the...
|
Forum: Troubleshooting
10-28-2013, 01:55 PM
|
Replies: 12
Views: 6,270
|
Forum: Troubleshooting
10-28-2013, 01:43 PM
|
Replies: 12
Views: 6,270
Thanks, guys!
Is this...
Thanks, guys!
Is this (http://www.moyermarine.com/cgi-bin/shopper.cgi?preadd=action&key=BRSS_05_434) the correct plug?
Shawn, does a chaser kit work only on the threads in the holes, or does...
|
Forum: Troubleshooting
10-28-2013, 12:04 PM
|
Replies: 12
Views: 6,270
Manifold drain plug is stripped
Hey guys,
My Ericson E-29 is on the hard for the winter, and I've just completed the winterizing. After removing the three drain plugs to allow the water out of the block, the plug on the carb...
|
Forum: Troubleshooting
09-30-2013, 11:11 AM
|
Replies: 21
Views: 8,034
Well, good news to report.
Went out this...
Well, good news to report.
Went out this weekend for another motoring test drive, and the oil pressure was perfect, both cold and warm.
I'll keep an eye on things, and also put cleaning up...
|
Forum: Troubleshooting
09-26-2013, 09:25 AM
|
Replies: 21
Views: 8,034
|
Forum: Cooling System
09-25-2013, 06:02 PM
|
Replies: 15
Views: 5,521
|
Forum: Cooling System
09-25-2013, 04:09 PM
|
Replies: 15
Views: 5,521
Very sound and sage advice, Shawn. And much...
Very sound and sage advice, Shawn. And much appreciated!
The first thing I really need to do is figure out what parts I have on the engine. I'm not certain if things like the water pump and...
|