Forum: Troubleshooting
09-17-2021, 06:09 PM
|
|
Replies: 38
Views: 7,124
Oil pressure issue resolved
Yes, I solved the oil pressure problem...the 3/4" nut at the oil pan was loosely fitted. I found out when I went to do an oil change. Did the oil change from straight 30 to three quarts of 20-50...
|
|
Forum: Troubleshooting
08-31-2021, 02:00 AM
|
|
Replies: 38
Views: 7,124
|
|
Forum: Troubleshooting
06-29-2021, 03:37 AM
|
|
Replies: 38
Views: 7,124
|
|
Forum: General Interest
01-02-2021, 03:20 PM
|
|
Replies: 5
Views: 1,877
|
|
Forum: General Interest
09-17-2020, 07:11 PM
|
|
Replies: 167
Views: 43,743
|
|
Forum: General Interest
09-16-2020, 04:09 AM
|
|
Replies: 167
Views: 43,743
|
|
Forum: General Interest
09-07-2020, 08:55 PM
|
|
Replies: 11
Views: 2,061
1. Torquing wrench obtained to re-torque the...
1. Torquing wrench obtained to re-torque the head bolts to 35 foot pounds;
2. Ordered the MMI 502 pump impeller (and impeller extractor tool);
3. Ordered the anti-siphon loop attachment (new...
|
|
Forum: General Interest
07-30-2020, 12:15 PM
|
|
Replies: 167
Views: 43,743
Yes, flow sensor is installed
Water pump is...
Yes, flow sensor is installed
Water pump is brand new
Yes, muriatic acid wash was done recently
Yes as to the bypass valve. Ok I’ll try removing the thermostat and closing the valve and report...
|
|
Forum: General Interest
07-30-2020, 12:30 AM
|
|
Replies: 167
Views: 43,743
|
|
Forum: General Maintenance
07-26-2020, 01:46 PM
|
|
Replies: 7
Views: 2,261
|
|
Forum: Overhaul
07-22-2020, 01:28 AM
|
|
Replies: 2
Views: 1,850
I just tore into it :D
I did however make...
I just tore into it :D
I did however make notes, took lots of pics and arraigned the lifters and springs in order from 1-8 from flywheel to aft.
I'm sure a more learned approach will by posted for...
|
|
Forum: General Interest
06-21-2020, 12:55 PM
|
|
Replies: 28
Views: 6,617
|
|
Forum: Overhaul
05-28-2020, 01:40 PM
|
|
Replies: 185
Views: 47,132
|
|
Forum: Overhaul
05-12-2020, 09:22 PM
|
|
Replies: 185
Views: 47,132
|
|
Forum: Fuel System
05-12-2020, 03:38 AM
|
|
Replies: 13
Views: 3,983
|
|
Forum: Reversing Gear
05-10-2020, 11:09 PM
|
|
Replies: 3
Views: 1,980
|
|
Forum: Cooling System
05-09-2020, 03:47 AM
|
|
Replies: 7
Views: 2,494
14999
This is my set up.
Re your...
14999
This is my set up.
Re your question as to whether it is advisable to run fresh water through the cooling system using a hose that is connected to a fresh water spout, the answer (based...
|
|
Forum: General Interest
05-09-2020, 03:33 AM
|
|
Replies: 167
Views: 43,743
Two tone painting of the top deck: Phase 2
After Phase 1, I have to admit that I had to take some time away from the lil yachty...I was burnt out. But I’m back. Phase 2 has begun. I got a late start today. I started at noon. By 5pm, I...
|
|
Forum: Overhaul
05-06-2020, 10:12 AM
|
|
Replies: 185
Views: 47,132
|
|
Forum: General Interest
04-28-2020, 04:04 PM
|
|
Replies: 167
Views: 43,743
|
|
Forum: General Interest
04-26-2020, 07:18 PM
|
|
Replies: 167
Views: 43,743
|
|
Forum: General Interest
04-26-2020, 11:43 AM
|
|
Replies: 167
Views: 43,743
From reading the directions on the paint can,...
From reading the directions on the paint can, reading articles on painting and watching YouTube videos, I learned to do the following:
*For previously painted surfaces
1. Clean the surface
2. ...
|
|
Forum: Introductions
04-25-2020, 02:13 AM
|
|
Replies: 22
Views: 8,250
What the others said about the float needle. As...
What the others said about the float needle. As for that nut: there are areas on the engine that, from rust and condensation etc, get fused. Be patient with it. Use the right size wrench first and...
|
|
Forum: Introductions
04-23-2020, 10:04 PM
|
|
Replies: 22
Views: 8,250
|
|
Forum: Polls
04-14-2020, 04:24 AM
|
|
Replies: 67
Views: 68,209
14883
??/28/74...it’s a ‘74, same as my boat...
14883
??/28/74...it’s a ‘74, same as my boat and about 45 (about the same age as me). Got an older one at home I am disassembling and rebuilding. I’ll look and report back at the date. Thx for...
|
