Forum: Overhaul
03-06-2008, 04:31 PM
|
Replies: 1
Views: 4,067
|
Forum: Cooling System
01-09-2008, 09:51 AM
|
Replies: 18
Views: 8,075
Dual Pump
Johnson makes a dual pump P/N's F4B-9 10-35098-2 &
F4B-9 10-24144-1 piggy backed together. We are using them on our S2
11A with Volvo Penta MD17C engine. One supplies the frest water cooling and...
|
Forum: General Maintenance
09-12-2007, 03:54 PM
|
Replies: 2
Views: 5,231
Parts Cataloge
Look here, I think you will find what you are looking for.
http://www.pearsonvanguard.homestead.com/files/Atomic_Four_Parts_Catalogue.pdf
Zack
|
Forum: Troubleshooting
07-29-2007, 12:27 AM
|
Replies: 5
Views: 6,761
I have found that even when you think you have...
I have found that even when you think you have all the passages in the carb clean they are sometimes not. Take a thin wire and run down the passages and see if you can see the other end. Then you...
|
Forum: Ranger
07-13-2007, 11:10 AM
|
Replies: 4
Views: 11,435
|
Forum: Ranger
11-13-2006, 08:27 PM
|
Replies: 4
Views: 11,435
Moving Main Sheet on R29
I want to move the traveler to just aft of the Companion way Hatch. I do not like having to trim the main from behind me and I can not add a bimini with the current set up. Has anyone else done ...
|
Forum: General Interest
10-16-2006, 09:34 AM
|
Replies: 3
Views: 5,301
|
Forum: General Maintenance
10-10-2006, 09:26 AM
|
Replies: 2
Views: 5,165
|
Forum: General Maintenance
10-08-2006, 11:46 AM
|
Replies: 2
Views: 5,165
Oil Regulator Sealing washer
I see that you have a entire kit for sale as item #OOIL_06_122. I need the washer with the rubber on it. Mine is gone from age and leaking a small amount of oil.
Do you offer only the washer...
|
Forum: Fuel System
10-07-2006, 03:13 PM
|
Replies: 6
Views: 4,306
Fixed idle problem
Don, thanks for you help. I found some blockage in the Idle passage. While it was apart, again, I cleaned the upper and lower idle ports. Now it purrs along at 800 rpm. I can get it lower but I...
|
Forum: Fuel System
10-06-2006, 05:36 PM
|
Replies: 6
Views: 4,306
Follow up - Took the carb off again and in...
Follow up - Took the carb off again and in checking things out, I notice when the butterfly was closed I could see light. I did not think this was the way it should be. I have another old carb that...
|
Forum: Fuel System
10-06-2006, 02:42 PM
|
Replies: 6
Views: 4,306
|
Forum: Fuel System
10-06-2006, 01:35 PM
|
Replies: 6
Views: 4,306
Facet Fuel Pump
My Facet fuel pump will not keep the polishing filter full. While running the engine at idle on the hard, I can see only a few drops per second coming into the clear filter. The filter is never...
|
Forum: Ignition System
10-06-2006, 01:29 PM
|
Replies: 3
Views: 6,097
|
Forum: Ignition System
10-06-2006, 09:37 AM
|
Replies: 3
Views: 6,097
Magnetic ring for Ignitor ignition
The top of my Magnetic ring is broken and what appears to be a piece of metal is separated from the ring. Would this have an adverse effect of the running of the engine. I must have broken it while...
|
Forum: Overhaul
10-04-2006, 09:27 AM
|
Replies: 0
Views: 5,001
Load Testing on the Hard
I have my rebuilt engine on the hard and am trying to design some method of putting a load on it. I feel sure some of you have done the same and have some ideas that would shorten the process. I do...
|
Forum: Fuel System
10-03-2006, 03:21 PM
|
Replies: 1
Views: 4,444
Vacuum Testing
Where do you connect the vacuum guage to? I can seem to find a place.
Thanks,
Zack
|
Forum: Wanted to Buy - Engines and Engine Parts
06-20-2006, 11:41 AM
|
Replies: 2
Views: 3,243
|
Forum: Overhaul
05-25-2005, 09:32 PM
|
Replies: 5
Views: 7,478
Idler Gear Shaft
I have removed the 2 set screws. I was planning on have the machine shop remove the shaft before cleaning the block. Now I am wondering if it is necessary to remove it for cleaning. It does not...
|
Forum: General Interest
05-19-2005, 04:31 PM
|
Replies: 13
Views: 60,271
Measurements
I will get full measurements tonight and post a couple more pictures tomorrow.
I put the tool in the boat, then hookup the chain hoist(on the U-Bolt), then hook the engine lifting eye/point...
|
Forum: Ranger
05-19-2005, 04:31 PM
|
Replies: 7
Views: 26,759
Measurements
I will get full measurements tonight and post a couple more pictures tomorrow.
I put the tool in the boat, then hookup the chain hoist(on the U-Bolt), then hook the engine lifting eye/point...
|
Forum: Ranger
05-17-2005, 03:14 PM
|
Replies: 7
Views: 26,759
Lever Arm Tool
Don, I made a lever arm tool to assist in installing and removing my A4 from a Ranger 29. With the use of the tool I installed my A4 from the back of a pickup onto the motor mounts in fifteen...
|
Forum: General Interest
05-17-2005, 03:14 PM
|
Replies: 13
Views: 60,271
Lever Arm Tool
Don, I made a lever arm tool to assist in installing and removing my A4 from a Ranger 29. With the use of the tool I installed my A4 from the back of a pickup onto the motor mounts in fifteen...
|
Forum: Overhaul
05-13-2005, 11:31 AM
|
Replies: 1
Views: 7,405
Valve Guide Removal
I am going to have my block cleaned and tested before continuing with the rebuild. Is it necessary to remove the valve guides before having this done. I have noticed that you recommend removing the...
|
Forum: Overhaul
05-10-2005, 05:24 PM
|
Replies: 2
Views: 6,071
Never Mind
I found the answer in similar posts. Sorry.
Zack
|