Moyer Marine Atomic 4 Community - Home of the Afourians

Moyer Marine Atomic 4 Community - Home of the Afourians (https://www.moyermarineforum.com/forums/index.php)
-   Polls (https://www.moyermarineforum.com/forums/forumdisplay.php?f=87)
-   -   Thru hull open or closed underway? (https://www.moyermarineforum.com/forums/showthread.php?t=11652)

Ando 09-06-2020 12:39 PM

Thru hull open or closed underway?
 
Here’s a poll to ask if you religiously close the thru hull while underway or leave it open. I religiously close it...problem is that I didn’t religiously open it (while battling high winds) and I think I will leave it open while underway just to have one less thing to do under scary circumstances.

roadnsky 09-06-2020 01:14 PM

Not sure why you would close the engine intake thru hull while underway?
There is a very high probability of needing to start your engine.
I can think of other reasons for closing it... but not while out sailing.

ndutton 09-06-2020 01:23 PM

. . . and such practice dictates working anti siphon protection in the exhaust injection line for safety - either a valve or a vented loop (my preference).

Ando 09-06-2020 01:54 PM

Quote:

Originally Posted by roadnsky (Post 122736)
Not sure why you would close the engine intake thru hull while underway?
There is a very high probability of needing to start your engine.
I can think of other reasons for closing it... but not while out sailing.

The concern for me was flooding the engine

SubtoSail 09-06-2020 03:01 PM

I found a checklist on my boat when I bought it that directed closing the raw water valve once shutting down the engine underway. The procedure to start was the same for starting at the pier and underway, and included opening the valve after the engine was running.
My practice is to leave the valve shut while starting next to the pier and then leave it open underway. I also get nervous about flooding the engine, and more often than not I will get antsy while cranking underway so I shut the valve then go back to starting. I’m sure takes less than three seconds to start, but it feels like minutes to me.

joe_db 09-07-2020 01:16 PM

Bottom line - closing the thru-hull is a band-aid covering up an issue that should be fixed.

edwardc 09-08-2020 12:05 PM

When I start the engine after its been sitting a day or more, I make sure the water intake is closed before cranking, in case the engine proves difficult to start (a frequent occurance in colder weather). I open the valve as soon as the A4 starts.

When the engine is warm, or has just been run within the last few houre, it always starts right up, so I leave the valve open while sailing. And yes, I do have an anti-siphon loop.

nyvoyager 09-08-2020 11:34 PM

I do much the same. It will often stay open for an entire extended cruise. Occasionally I may close it at anchor for the night for a cold start later on.

Quote:

Originally Posted by edwardc (Post 122762)
When I start the engine after its been sitting a day or more, I make sure the water intake is closed before cranking, in case the engine proves difficult to start (a frequent occurance in colder weather). I open the valve as soon as the A4 starts.

When the engine is warm, or has just been run within the last few houre, it always starts right up, so I leave the valve open while sailing. And yes, I do have an anti-siphon loop.


joe_db 09-09-2020 01:22 PM

IMHO if cold starts take that much doing, perhaps track down why? In my case it was worn/dirty points.

edwardc 09-10-2020 12:31 PM

No points: Electronic ignition.

A properly tuned updraft carb should be a little hard to start.

Years ago, I added an oxygen sensor and an air:fuel ratio gauge. Using an adjustable main jet, I have the ratio at cruise rpm set very close to the ideal 14.7:1.
At idle, I set the mixture slightly richer in order to make starting a little easier. In summer, a cold start with full choke always takes two tries. Very predictable. This increases in the fall as temperatures go down.

I did some experimenting, and found that adjusting the idle mix so it started cold on the first try was significantly richer than 14.7:1 and resulted in more fouled looking plugs.

capnward 09-13-2020 12:57 PM

Apparently I have the mixture adjusted rich, because my A4 almost always starts on the first try with a choke when cold, and without a choke once warm. Once it's warm it starts in less than a second. Cold with choke on, it starts in 4 seconds. If I prime the fuel line with the bail on the mechanical fuel pump before I start it cold, it starts quicker. It started on the first try this spring. I used engine fogging spray when closing down for the winter, and put a little MMO into the cylinders and let it soak in for a day before starting. I have EI, and an adjustable main jet.
It seems to be running well. I haven't checked the plugs for fouling since last year, but I change plugs every year, until this year. I have a water jacketed exhaust with an anti-siphon. I like the fact I can start up on a moment's notice without closing a thru hull first. I leave the water intake thru hull open all the time, except when I leave the boat for the winter. My definition of underway includes motoring, so closing the water intake underway never occurs to me.
If the engine ever didn't start within 5 seconds, I might close the thru hull until it caught, but I think the water jacketed exhaust prevents water from backing up into the cylinders. The problem many people have of water getting into the cylinders because they cranked it too much with the thru hull open has never happened to me. I don't run the starter for more than 5 seconds at a time with the thru hull open. If it doesn't start in 5 seconds, holding the starter in longer won't help, and may overwhelm your exhaust with water if the thru hull is open. If the fuel line has run dry, it might take several 5 second pulses to draw fuel from the tank to the carb. Manually pumping the mechanical pump will speed up that process, as will bypassing the OPSS on an electrical pump.

campbdon 08-22-2021 07:17 PM

I too have learned to keep the thruhull valve closed except after the engine has started and/or while sailing. Otherwise closed. Has anyone the worry that opening and closing the thruhull this regularly could lead to the risk of a thruhull (catastrophic) failure at some time? I was thinking to leave the valve mostly opened and open/close another (new) valve in the intake hose. Just wonderin??

DonC

JOHN COOKSON 08-23-2021 03:10 PM

Quote:

Originally Posted by campbdon (Post 126727)
. Has anyone the worry that opening and closing the thruhull this regularly could lead to the risk of a thruhull (catastrophic) failure at some time? I was thinking to leave the valve mostly opened and open/close another (new) valve in the intake hose. Just wonderin??
DonC

Electrolysis is a threat to underwater metals.
A proper "marine grade" installation should last indefinately with normal use.
Gate valves are a problem waiting to happen.
If you open and close the through hull valves occasionally it will keep them from "freezing" or corroding in the open or closed position.

ex TRUE GRIT

campbdon 08-23-2021 04:42 PM

Thanks John. For a typical sail that would mean 4 open/close cycles times about 20 sailings/yr. That seems to me to be more than occasional. I thought maybe by installing a second valve in series I could alternate their usage thus reducing the number of switch cycles per valve. Anyway my thruhull uses a ball valve (lever moves 45 degrees, inline or perpendicular to the line) though I don't know if all the parts are bronze or brass. I sail only in fresh water. I think it's the original installation (43yrs).
DonC

JOHN COOKSON 08-23-2021 06:35 PM

The handles can rust off too.
I don't see any problem with a series arrangement you mentioned.
If the valves are the original and\or you have any doubts about their integrity (it sounds as if you do) I'd replace them with new. Maybe an inspection of the whole through hull fitting also?
Doubts are not good things to have when you are out on the water.

ex TRUE GRIT


All times are GMT -4. The time now is 07:16 PM.

Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2024 Moyer Marine Inc.

All Rights Reserved