Moyer Marine Atomic 4 Community - Home of the Afourians

Moyer Marine Atomic 4 Community - Home of the Afourians (https://www.moyermarineforum.com/forums/index.php)
-   Wanted to Buy - Other items (https://www.moyermarineforum.com/forums/forumdisplay.php?f=70)
-   -   Mast spreader brackets or spreader 72 columbia 30 (https://www.moyermarineforum.com/forums/showthread.php?t=11880)

Rando1201 05-04-2021 05:57 PM

Mast spreader brackets or spreader 72 columbia 30
 
I am looking for a replacement for the spreader brackets that mount to the mast. Can't find them anywhere, my mast in on laydays in the yard, the old cast aluminum mount broke as we were prepping the mast.

Any help is appreciated.

Mo 05-05-2021 07:06 PM

If you have the pieces it can be welded. We had a guy at the club break a spreader bracket on a Tanzer 31. They dropped he mast and it broke just out from where it joins he mast. His insurance wiggled and waggled over it and the plan was to send it on a 1500 mile flatbed run to have it "repaired".

I looked at it and told him I knew a guy who could weld it no problem. He didn't want that, so he went to insurance. Their plan was to send it to Ontario and have some shop weld it "Professionally". I smiled when I heard that. The mast sat for 4 months and finally he'd had enough of the delays (covid etc). Gave him the number of the guy I know and he came to the club and welded it. These particular ones couldn't be removed from the mast.

The job was a fraction of the cost of sending it out. He also had the option to have some made up by the same guy but a simple weld was done and he sailed it all last year without issues.

Not a job for a trainee...need to find an awesome welder in your area. Doesn't take long for the right guy to do.

Edit: If you can drill rivets and remove them and bring them into shop that does a lot of aluminum work I think you'd be surprised.

Mo 05-05-2021 07:33 PM

Here's a link to check out. If yours are the same as the ones in the pic you have a few choices.

You can:
1. have them welded
2. make up a set of brackets spreaders and rivet them in place. A hole as noted in one of the pics in the link would have to be closed (plated) by preferably welding, then rivet new bracket to that. If there is no hole you just make the brakets and rivet them on.
3. you might be able to find a spreader repair kit or a spreader kit and rivet them to the mast.

https://www.cruisersforum.com/forums...ld-144119.html

Rando1201 05-07-2021 11:16 AM

Quote:

Originally Posted by Mo (Post 125441)
Here's a link to check out. If yours are the same as the ones in the pic you have a few choices.

You can:
1. have them welded
2. make up a set of brackets spreaders and rivet them in place. A hole as noted in one of the pics in the link would have to be closed (plated) by preferably welding, then rivet new bracket to that. If there is no hole you just make the brakets and rivet them on.
3. you might be able to find a spreader repair kit or a spreader kit and rivet them to the mast.

https://www.cruisersforum.com/forums...ld-144119.html

Oh man thanks, in the meantime I actually found the part, unfortunately, its $469.00 and to be thorough id probably order 2? Or do you think one is sufficient. https://www.rigrite.com/Spars/Rig-Ri...5tzE6IMXLQdjGA

Mo 05-07-2021 04:53 PM

If purchasing two isn't going to take food off the table by all means do that. You could replace just one, no problem. Most breaks are from hitting them while transporting or raising the mast. I think a loose rig wouldn't help either.

All the best.


All times are GMT -4. The time now is 02:27 PM.

Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2024 Moyer Marine Inc.

All Rights Reserved