Forum: Electrical
07-26-2021, 03:32 PM
|
Replies: 5
Views: 1,549
|
Forum: Ignition System
06-27-2021, 07:51 PM
|
Replies: 3
Views: 4,707
Welcome to the forum. :)
The resistor...
Welcome to the forum. :)
The resistor normally looks like a long lego made out of ceramic and having wires or terminal on it. it usually measure out 1.5-2.0 ohms-ish. To see if you had one,...
|
Forum: Troubleshooting
06-25-2021, 11:42 AM
|
Replies: 17
Views: 2,689
Ok, Confessions of an idiot
Just got up to the boat yesterday and found the problem. In my enthusiasm to replace the leaking manifold i forgot to block the 1/8” NPT port immediately above the carb flange, causing the engine to...
|
Forum: General Interest
06-22-2021, 02:22 PM
|
Replies: 0
Views: 1,467
Off-Topic: I Love the pitch on some amazon items
OK, I know this off-topic for A4s... but it both made me smile and shake my head. That said, in my defense... it does say it's waterproof. :p
Take the look at the first pic, the one with the...
|
Forum: Troubleshooting
06-15-2021, 02:09 PM
|
Replies: 38
Views: 7,550
Ando--
Following Jerry's update above, when...
Ando--
Following Jerry's update above, when I swapped from the "modern" (eg. more cost effective, cheap) version with the ball bearing, spring and bolt/washer/nut to the original integrated...
|
Forum: Troubleshooting
06-15-2021, 01:11 PM
|
Replies: 17
Views: 2,689
|
Forum: Fuel System
06-15-2021, 01:04 PM
|
Replies: 11
Views: 1,531
I've had good luck with Earl's fuel supply...
I've had good luck with Earl's fuel supply components. The nice thing about Earl's is they are aluminum, anodized and have smooth retention for the hose clamp. However, a well placed and tightened...
|
Forum: Fuel System
06-15-2021, 12:49 PM
|
Replies: 22
Views: 15,619
I just did that for my boat. While I'll never...
I just did that for my boat. While I'll never have to worry about rust again and can now see the tank level by just looking, you will pick up a hint of gasoline smell if the boat has been bundled up...
|
Forum: Overhaul
05-23-2021, 07:48 PM
|
Replies: 123
Views: 29,384
Greg--
You should be able to grab the crank...
Greg--
You should be able to grab the crank and rotate the assembly by hand. There will be resistance getting it moving but one it's moving it should feel smooth.
Just grab one the connecting...
|
Forum: Good Guys
05-15-2021, 12:05 PM
|
Replies: 9
Views: 3,776
|
Forum: Cooling System
05-15-2021, 11:56 AM
|
Replies: 10
Views: 2,231
|
Forum: Cooling System
05-15-2021, 10:11 AM
|
Replies: 10
Views: 2,231
You should be fine. The slot-end of the shaft...
You should be fine. The slot-end of the shaft mates with a pin in accessory drive. The entire inner accessory drive is part of the crankcase oil system, so it fully possible that a bit of oil left...
|
Forum: Cooling System
05-14-2021, 12:31 PM
|
Replies: 6
Views: 1,930
|
Forum: Ignition System
05-14-2021, 10:38 AM
|
Replies: 20
Views: 4,305
|
Forum: Reversing Gear
05-08-2021, 09:13 PM
|
Replies: 6
Views: 1,731
|
Forum: Reversing Gear
05-06-2021, 09:03 PM
|
Replies: 6
Views: 1,731
|
Forum: Cooling System
05-04-2021, 01:03 PM
|
Replies: 5
Views: 1,963
|
Forum: Fuel System
04-30-2021, 05:41 PM
|
Replies: 16
Views: 3,160
|
Forum: Troubleshooting
04-30-2021, 05:35 PM
|
Replies: 21
Views: 3,052
|
Forum: Troubleshooting
04-30-2021, 01:34 AM
|
Replies: 6
Views: 1,663
|
Forum: Exhaust System
04-28-2021, 10:55 AM
|
Replies: 9
Views: 2,349
It there is slack in the hoses so you can pull...
It there is slack in the hoses so you can pull them together without too much tension, just look for a hose repair coupling (not plastic) with the correct inside diameter. That said, I would look at...
|
Forum: General Maintenance
04-26-2021, 01:09 PM
|
Replies: 18
Views: 4,990
|
Forum: General Maintenance
04-25-2021, 07:56 PM
|
Replies: 18
Views: 4,990
|
Forum: General Maintenance
04-25-2021, 05:42 PM
|
Replies: 18
Views: 4,990
|
Forum: Cooling System
04-24-2021, 11:10 AM
|
Replies: 7
Views: 1,507
|